Lightolier 1094 User manual

Lightolier
Brand
Lightolier
Model
1094
Category
Wall & ceiling mounts accessories
Type
User manual
\
,, ;
,-
.,’
.,
—.
d
READ AND UNDERSTAND T“HESE INSTRUCTIONS BEFOf+E INSTALLING FIXTURE
INSTRUCTION SHEET NO.
This fixture is intended forinskdlation in accordance with the National
Electrical Code and Iocaf
regulations.To assure full complian= with local maes and regulations, check witt your iocai elee~icai
IS:4910
inspector before installation. To prevent eleckk=al shack, turnoff electriaty at fuse box before proceeding.
,. ..2. . .-. ? ..=
Retain these instructions
for maintenance reference.
, -1094+AGE-I–”OF: --2
5
I
INSTRUCTIONS FOR lNSTAtLATION
I
I
., .,. ,.,
...- -
I
I
I
,.
A.”:”~o~’ (j&~Go~fi: ‘oTJiLET BOX MOUNTING.
1...Loosen and remove BATTERY NUT that secures MOUNTING PLATE” to
. .
.FIXT~E BODY. Remove MOUNTING PLATE from;>FIXTURE BODY.
.:?.
..!:’,
Screw COVER PLATE to the backside, of MOUNTING PLATE with SCREWS
provided.
~’3. Pull supply wires from OUTLET BOX through WIREWAY HOLE in
MOUNTING PLATE.
“,,’4.’Using outlet box screws (provided’ with outlet box) secure
“MOUNTING PLATE to outlet box using appropriate slots in MOUNT-
%.
ING PLATE.
n;:&
,.
B::FOR VERTICALLY MOUNTED RECTANGULAR GEk OR SWITCH BOXES.
1. Loosen and remove BATTERY NUT that secures MOUNTING PLATE to
i
FIXTURE BODY. Remove MOUNTING PLATE from FIXTURE BODY.
Pull supply wires from outlet box through the WIREWAY HOLE in
MOUNTING PLATE.
2.
Using OUTLET BOX SCREWS: (provided with outlet box) secure the
MOUNTING PLATE to OUTLET BOXusing the two horizontal slots.
c. INSTALLATION OF FIXTURE BODY.
1.
While supporting fixture, make Connections.
Black fixture lead
or fixture lead without tracer marks to black (ho:) supply lead
white fixture lead or fixture lead with tracer marks to white
.,
(neutral) supply lead.
Uninsulated fixture wires are ground
wires and all must be connected to grounding terminal or wire
in outlet box.
Use wirenuts (local hardware item) .
OL’TLEEBOXq
\
!40UNTING
COVER
\
P
a
I_
HORIZONTAL
SLOT
/
THREADED
BALLS
?!!!!!! -
THREADED
-% > II
STUDS
):
1.
GLASS
\
SLOT
“.
.“
,“
“O
/’
.“
\
-BATTERY
.“
NUT
::’ZR;;5--I
EECTANGUMR SLOTS
FIXTUREBODY
WIRE NUT
HOUSINGTAB
..
/
\
READ AND UNDERSTAND THESE iNSKiUCTIONS BEFORE INSTALLING FIXTURE
INSTRUCTION SHEET NO.
~~1~ fi~re i5 jntended for installation in
amrdancz with tie National Eiectrirzl Code and 10d
~eoula~ons.To assure full campliancevfi!! local
males and regulations, Cheti with you; Iod elecrrd
“[s:a9 ,10
inspector
beroreinstallation. To preventelecbical shock,turnoff,electriaty atfuseboxbeiore proceeding.
Retain these instructions for maintenance reference.
“--1094 PAGE”2 “OF 21:
——.,,———...—... .- .—-—.
I
I
I
.-
. . .. . .
.
,. -.. .
NOTE :
For supply connections use wire rated for “at least 75° C.
__.._:-——-J
WARNING-RISK OF FIRE.. Most dwellings built before 1985 have supply
wire rated 60° C.
~consult”.a,.qualified electrician before
installation.
;’.7.
CAUTIO.~: Push SUPPIY wires.and wir”enut c~nriections back into j-box
:?
2. Mount FIXTURE BODY to MOUNTING PLATE by aligning HOUSING TABS
up ,,through RECTANGULAR SLOTS in MOUNTIN~ PLATE.
CAUTION: Make certain that no wires are pinched between mounting
plat,e and fixture body.
.3.
Gen$ly push fixture body against wall until MOUNTING STUD comes
thcough SLOT in FIXTURE BODY.
Secure in place using battery nut
4.
Install recommended lamp.
CAUTION: Maximum wattage marked on fixture must not be exceeded.
5.
Install GLASS
over two THEADED STUDS WITH etched pattern on
glass facing down,
tighten two THREADED BALLS onto THREADED
STUDS to secure glass. Do not overtighten!’
Note: glass should be
sure on front portion
-.
1
!
I
1
---
I
removed for cleaning as undue downward pres-
could cause glass support bracket to bend.
,..,
.. -
.
;
..:,
,,
. . . .
-...’
.-
.—.—. .—-. .
. . . . .-_— ... - .-
—
r
,..
(
-L-.
  • Page 1 1
  • Page 2 2

Lightolier 1094 User manual

Lightolier
Brand
Lightolier
Model
1094
Category
Wall & ceiling mounts accessories
Type
User manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents