Steelcraft 415029BP User guide

Steelcraft
Brand
Steelcraft
Model
415029BP
Type
User guide

This manual is also suitable for

Steelcraft 415029BP is a set of 5-inch oval bent end sidebars compatible with the 2021 Ford Bronco 4-door model. These sidebars are designed to provide both functionality and style to your vehicle, enhancing its off-road capabilities and aesthetic appeal. With their robust construction and durable finish, they offer reliable protection against potential damage from obstacles encountered during off-road adventures. The sidebars also serve as convenient steps, making it easier to enter and exit the vehicle, especially when carrying gear or equipment.

Steelcraft 415029BP is a set of 5-inch oval bent end sidebars compatible with the 2021 Ford Bronco 4-door model. These sidebars are designed to provide both functionality and style to your vehicle, enhancing its off-road capabilities and aesthetic appeal. With their robust construction and durable finish, they offer reliable protection against potential damage from obstacles encountered during off-road adventures. The sidebars also serve as convenient steps, making it easier to enter and exit the vehicle, especially when carrying gear or equipment.

5INCH OVAL BENT END SIDEBARS
2021 FORD BRONCO 4DR
Page 1 of 3 REV1 4/29/22 (CC)
PARTS LIST:
1
Driver/Left Sidebar
12
10mm x 30mm Hex Bolts
1
Passenger/Right Sidebar
12
10mm Lock Washers
2
Front Mounting Brackets
12
10mm x 27mm OD x 3mm Flat Washers
2
Center Mounting Brackets
12
8mm x 25mm Combo Bolts
2
Rear Mounting Brackets
PROCEDURE:
1. REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ INSTRUCTIONS
CAREFULLY BEFORE STARTING INSTALLATION.
2. Starting from underneath the Passenger/Right body panel, locate the front mounting location and the
threaded holes in the body panel, (Figure 1). Remove the plastic plugs covering the holes.
3. Select the Passenger/Right Front Mounting Bracket. Attach the Mounting Bracket to the front location
with (2) 10mm Hex Bolts, (2) 10mm Lock Washers and (2) 10mm Flat Washers, (Figure 2). Do not
tighten hardware.
4. Repeat Steps 2 & 3 to attach (1) Center Mounting Bracket and (1) Rear Mounting Bracket to the center
and rear locations, (Figures 3—6). Do not tighten hardware.
5. Select the Passenger/Right Sidebar. Place the Sidebar onto the cradles of the Mounting Brackets.
IMPORTANT: Do not rotate or slide the Sidebar front to back or damage to the finish may result. Attach
the Sidebar to the Mounting Brackets with (6) 8mm Combo Bolts, (Figure 7). Do not tighten hardware.
6. Level and adjust the Sidebar and tighten all hardware.
7. Repeat Steps 1—6 to attach the Driver/Left Sidebar.
8. Do periodic inspections to the installation to make sure that all hardware is secure and tight.
To protect your investment, Do not use any type of polish or wax that may contain abrasives that could damage the
finish. Mild soap may be used to clean the Sidebars.
Front
Passenger/Right
Sidebar
(2) Front Mounting
Brackets
(2) Center Mounting
Brackets
*Notice: Rear Bracket contains a circle while center bracket does not
(2) Rear Mounting
Brackets
5INCH OVAL BENT END SIDEBARS
2021 FORD BRONCO 4DR
Page 2 of 3 REV1 4/29/22 (CC)
Passenger/Right side Installation Pictured
(Fig 1) Passenger/Right Front mounting location
Front
Front
(Fig 2) Attach the Passenger/Right Front
Mounting Bracket to the front location
(2) 10mm Hex Bolts
(2) 10mm Lock Washers
(2) 10mm Flat Washers
5INCH OVAL BENT END SIDEBARS
2021 FORD BRONCO 4DR
Page 3 of 3 REV1 4/29/22 (CC)
Passenger/Right side Installation Pictured
(Fig 5) Passenger/Right Rear mounting location
Rear
(Fig 7) Attach the Passenger/Right
Sidebar to the Mounting Brackets
(2) 10mm Hex Bolts
(2) 10mm Lock Washers
(2) 10mm Flat Washers
(Fig 4) Attach (1) Passenger/Right Center
Mounting Bracket to the Center location
Front
(2) 8mm Combo Bolts
(Fig 6) Attach (1) Passenger/Right Rear
Mounting Bracket to the Rear location
(2) 10mm Hex Bolts
(2) 10mm Lock Washers
(2) 10mm Flat Washers
  • Page 1 1
  • Page 2 2
  • Page 3 3

Steelcraft 415029BP User guide

Steelcraft
Brand
Steelcraft
Model
415029BP
Type
User guide
This manual is also suitable for

Steelcraft 415029BP is a set of 5-inch oval bent end sidebars compatible with the 2021 Ford Bronco 4-door model. These sidebars are designed to provide both functionality and style to your vehicle, enhancing its off-road capabilities and aesthetic appeal. With their robust construction and durable finish, they offer reliable protection against potential damage from obstacles encountered during off-road adventures. The sidebars also serve as convenient steps, making it easier to enter and exit the vehicle, especially when carrying gear or equipment.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents