BABYSTYLE LUX TWIN CLASSIC Operating Instructions Manual

Brand: BABYSTYLE

Model: LUX TWIN CLASSIC

Category: Strollers

Type: Operating Instructions Manual

This manual is also suitable for

BABYSTYLE LUX TWIN CLASSIC is a versatile stroller designed for the comfort and safety of your little ones. With its adjustable backrest, footrest, and handle, this stroller offers multiple positions to accommodate your growing children. The stroller features a spacious seat unit or pram body that can be easily attached or removed, making it suitable from birth. It also includes a sit-up board for the pram body, allowing your child to sit up comfortably when ready.

This manual applies to the following models

LUX 3 in 1, LUX 2 in 1 & LUX TWIN CLASSIC

OPERATING INSTRUCTIONS

IMPORTANT: Read these instructions carefully before use and keep them for further

reference. Your child’s safety may be affected if you do not follow these instructions.

5406_F_Implast_ lux.indd 1 2006-11-22 08:37:33

www.implast.com.pl

IMPORTANT – Please read these instructions carefully before using your new

pram / pushchair. Keep this manual in a safe place for future reference. This

product complies with TÜV and British Standard BS 7409: 1996.

Important Safety Information

• WARNING: A child’s safety is your responsibility

• WARNING: Children should never be left unattended in this vehicle.

• It is important that any person intending to use this vehicle fully understands

the instructions.

• WARNING: Children should be harnessed in this vehicle at all times. Use the

ve point harness that is provided, make sure the harness is securely fastened

to the “D-rings” situated on the chassis either side of the seat. Adjust the

harness to its correct position with the use of the adjustable straps.

• WARNING: Children should always be kept clear of moving parts while

making adjustments to the vehicle.

• Never overload the vehicle. Maximum weight of child should not exceed 15

kg. The weight limit for the shopping tray is 3 kg. Always place articles in the

centre of the tray provided. Any load attached to the handle will adversely

affect the stability of the vehicle.

• WARNING: Incorrect assembly, folding or use of this vehicle may cause

damage and affect the safety of the vehicle.

• It may be unsafe to use accessories (e.g. child seats, bag hooks, rain covers

etc.) other than those approved by the manufacturer.

• WARNING: Never leave the vehicle without rst engaging the parking device.

Avoid uphill or downhill parking.

• Avoid using the vehicle on steps, stairs or escalators as it may be dangerous

to your child/children.

• Check on a regular basis to make sure that all essential components &

locking devices are functioning correctly.

• When the pram body is used , the depth from the top of the mattress to the

top of the side of a body at, or at any position within 300 mm from, the har-

ness attachment points, should not be reduced to less than 140mm when the

mattress is in position. Any mattress purchased separately should conform to

BS1877: Part 10 .

• Do not use replacement parts other than those supplied by the manufacturer

or distributor.

• Never use this vehicle as a permanent bed for your child / children.

BS 7409: 1996 label

WARNING: A CHILDS SAFETY IS YOUR RESPONSIBILITY.

Children should be harnessed in at all times and should never be left unattended. The child

should be clear of moving parts while making adjustments. This vehicle requires regular

maintenance by the user. Overloading, incorrect folding and the use of non-approved

accessories may damage or break this vehicle. Read the manufacturer’s instructions.

5406_F_Implast_ lux.indd 2 2006-11-22 08:37:33

www.implast.com.pl

WARNING: This pram has been designed to be operated as shown in the instructions.

Failure to follow these instructions may cause damage and render the guarantee void.

Fitting/Removing the wheels

• To t the wheels. Turn the chassis on its

side and gently slide the wheel on to the

axle until it stops, now depress the steel

clip (found in the centre hub of the wheel)

until the wheel drops further on to the axle

and stops. Release the steel clip and slide

the wheel back (as if removing) until the

wheel locks into position (Picture 1).

Check that the wheels are tted securely

before use.

• To remove the wheels, depress the

metal clip while simultaneously easing

the wheel off with a twisting action. Care

should always be taken when tting &

removing wheels.

Unfolding the chassis

• To erect the chassis apply the parking

device; pull the handle upwards

and over following the direction of the

arrow (Picture 2). Check that the two

sliders on either side of the chassis are

locked in position (Picture 3).

PNEUMATIC TYRES: Please note that pneumatic tyres; by their nature are prone to

puncture, punctures can be repaired with a standard puncture repair kit or the inner-tube

can be replaced. Remember that rubber tyres can leave marks on some surfaces (see

General Care & Maintenance).

5406_F_Implast_ lux.indd 3 2006-11-22 08:37:34

www.implast.com.pl

Attaching the seat unit or pram body

• Tilt the seat unit or pram body

forward and locate the two front

pegs in the attachment mechanism

(no. 1, Picture 4). Gently push

down until the two pegs lock into

position; now tilt the unit backward

until the rear attachment pegs lock

into the rear attachment mechanism

(no.2, Picture 4). ENSURE THAT

THE SEAT UNIT OR THE PRAM

BODY IS SECURELY FITTED

BEFORE USE.

• To remove the seat unit

or pram body. Gently apply

downward pressure to the seat

frame or pram body & then

push the red attachment

mechanism lever (no.1,

Pictrue 5) forward until it stops,

repeat this action on the opposite

side. Standing in the pushing position;

tilt the seat or bassinet unit upward

until the two forward attachment

pegs are released from the attachment

mechanism; now slide the two rear

pegs from their attachments and lift

the unit clear of the chassis.

Pram body sit-up board

The pram body is equipped with a sit-up

board. The sit-up board is for use as

a back rest when your child is ready to sit

up. The sit-up board can be

erected/reclined to three positions

or folded at into the sleeping position.

To erect the sit-up board lift the top

of the sit-up board and locate

the support bar (at the back of the sit-up

board) in the desired position.

The support bar locates in the plastic

housings on the inside base of the pram

body. To recline the sit-up board;

release the support bar and recline the

sit-up board back rest (Picture 6).

5406_F_Implast_ lux.indd 4 2006-11-22 08:37:34

www.implast.com.pl

Fitting the hood

Seat Unit/ Pram Body

• To attach or remove the hood.

Push the hood bracket into the

plastic housing until it clicks (Picture 7).

• To remove the hood, depress the

plastic latch at the bottom of the

bracket and pull upwards.

NOTE : Some models are supplied

(depending on design) with a valance

that ts via a zipper to the rear bottom

edge of the hood. The valance is

designed for use with the hood when

used in conjunction with the seat unit.

Fitting the front bar

• To attach front bar, push the front

bar bracket into the plastic housing

until it clicks (Picture 8).

• To remove the front bar, depress

the plastic latch at the bottom

of the bracket and pull upwards

simultaneously.

Adjusting the seat

unit backrest

• To adjust the position of the seat unit

backrest, support the seat back in one

hand press-in button (picture no 9.).

While holding the button in; reposition

the backrest as desired and release

the button. The backrest has 5 usable

positions.

Adjusting the seat

unit backrest

(Twin Classic only)

• To recline an individual seat unit

backrest, gently pull the bar in the

middle of the back of the seat backrest,

recline the seat to one of its three

positions and release the bar, the seat

will automatically drop into position.

5406_F_Implast_ lux.indd 5 2006-11-22 08:37:35

www.implast.com.pl

Adjusting the footrest

• To adjust the footrest press the two

buttons on the top of the footrest and

lift or lower the footrest to the desired

position (Picture 11).

Adjusting the handle

• To regulate handle, simultaneously

push the two buttons of the handle

height adjuster and rotate the handle

to the desired position (Picture 12).

Operating the brake

• To engage the parking device, push the

lever down with your foot until it locks

into position. Avoid uphill or downhill

parking. Never let go of the handle. To

release the brake, lift up with your foot

(Picture 13).

10.

11.

12.

13.

Fitting the bed

extension

• To attach the bed extension, remove

front bar, set the footrest to horizontal

position (see Adjusting the footrest) and

push the bed extension brackets into the

plastic housing until it clicks. To remove

the bed extension, depress the plastic

latches at the bottom of the bracket and

pull upwards simultaneously (Picture 10).

Fitting the head hugger

(Twin Classic only)

• To t the head hugger (remove the

hood if tted); attach the press-studs on

the head hugger to the corresponding

press-studs on the rear outside part

of the seat unit armrests. Replace the

hood. Note: The base fabric of the head

hugger should always be behind the seat

unit backrests

5406_F_Implast_ lux.indd 6 2006-11-22 08:37:35

www.implast.com.pl

Folding the chassis

• To fold the chassis, pull back the two

sliders on either side of the chassis handle

& release the secondary safety catch, gently

let the chassis close (Picture 14).

Using the handle height adjusters; fold the

handle back on itself to make the folded

chassis more compact (Picture 15).

Safety harness

•

Always apply the parking brake before

placing your child in the vehicle.The safety

harness has two shoulder straps, two waist

belts and a crotch strap. Place the two

shoulder straps over the child’s shoulders

and the waist belts around the child’s waist,

the crotch strap should be placed between

the child’s legs. The shoulder straps and

the waist belts should be clipped into

the buckle at the end of the crotch strap

(Picture 16).

The harness can be adjusted

to suit your child by sliding the adjusters

along the shoulder straps and waist belts.To

release the safety harness, push the bottons on

the centre buckle. D-rings for attaching a separate

harness conforming to BS 6684 can be found on

either side of the seat frame near the backrest

and seat base hinge.

15.

14.

SAFETY CATCH

Fitting/removal of Britax

car seats to the LUX chassis

(Excludes Twin Classic)

The Lux can be tted with the following Britax Infant Carriers: Babysure and

Rock -a-Tot Plus SI

•

To attach the car seat adaptor frame to the chassis place the frame so that all four

pins rest in the attachment devices. Push the frame down until the frame clicks and

locks into position. The adaptor frame should be orientated so that the bend in the

adaptor frame is upwards and the thinnest cross bar of the adaptor is closest to the

handle end of the chassis. Rest the car seat on the adaptor and allow the two slots on

the car seat rockers to locate on the thin cross bar. Fasten the locking clip (located at

the rear of the car seat backrest) around the adaptor frame. Check that the adaptor

is securely attached to the chassis and that the car seat is securely attached to the

adaptor before use. Refer to the Britax car seat USER GUIDE for further information

on harness use and tting the infant carrier into a car. To remove the car seat from

the adaptor; release the clip at the rear of the seat and lift the car seat upwards and

clear of the adaptor frame. The adaptor frame can be removed from the chassis by

following the procedure for removing the seat unit or pram body.

16.

5406_F_Implast_ lux.indd 7 2006-11-22 08:37:36

HOW TO LOOK AFTER

YOUR PRAM/PUSHCHAIR

• Routinely clean the metal parts with a damp cloth and then dry immediately.

• Fabrics should be cleaned using lukewarm water and a mild detergent. Do not

use aggressive cleaning agents. Do not wash in the washing machine.

• Regularly check screws, rivets, bolts & fastenings to ensure they are locked

tight and secure. Replace any parts in an inferior condition. Should you intend

to use the pushchair during the winter, by the sea or off-road; it is important to

clean thoroughly & dry the vehicle after use. Salt from the ocean or foam roads

will corrode metal parts if the vehicle is not cleaned after use.

• Check on a regular basis that all chassis locking devices are working correctly.

• If any part of the pushchair is damaged contact your local Babystyle retailer

immediately without using the pushchair.

• Petroleum jelly is suitable to use as a lubricant.

• Ensure that zips are either fully open or fully closed or they may be damaged.

• Always use a rain-cover in inclement weather.

• Do not place items on the hood/canopy, it may damage the vehicle and/or

render it unsafe.

• Rubber tyres can leave marks on some surfaces. The tyres can react

with some surfaces ( vinyl  oor coverings, carpets etc.) and cause stains.

Always stand the stroller on a protective surface indoors.

• Do not expose your pushchair to excessive sunlight for extensive periods of

time & take care not to tear the fabrics while transporting the pushchair.

WARRANTY

Babystyle UK Limited provides a warranty in support of the retailer from whom

you purchased this product. The warranty is effective for 6 months from the

date of purchase for the original purchaser/owner. Proof of purchase will ( at

the discretion of Babystyle UK Limited) be required in order for your retailer

to claim on the warranty. The warranty excludes any fault caused by misuse,

damage or neglect. It is the user’s responsibility to undertake routine inspection

and maintenance of the vehicle in order to avoid damage to the vehicle and/or

injury to the child. The vehicle is returned to the retailer at the owner’s expense

in order to ascertain if a claim under warranty is justi ed. Please read the

instructions carefully to look after your stroller.

BabyStyle UK Ltd.

36 Charles Street, Sileby, Leicestershire, LE12 7RJ

Tel: 01509 816444 Fax: 01509 816555

Email: [email protected]

www.babystyle.co.uk

5406_F_Implast_ lux.indd 8 2006-11-22 08:37:36

BABYSTYLE LUX TWIN CLASSIC Operating Instructions Manual

Brand: BABYSTYLE

Model: LUX TWIN CLASSIC

Category: Strollers

Type: Operating Instructions Manual

This manual is also suitable for

Download PDF

report

BABYSTYLE LUX TWIN CLASSIC Operating Instructions Manual

This manual is also suitable for

BABYSTYLE LUX TWIN CLASSIC Operating Instructions Manual

Related papers

Other documents