Leviton ODS10-IQE Installation guide

Brand: Leviton

Model: ODS10-IQE

Category: Motion detectors

Type: Installation guide

This manual is also suitable for

ODS10-IQI

Leviton ODS10-IQE is a designer wall switch occupancy sensor that can automatically switch your lights on and off based on motion detection. It's a self-contained device that provides sensing and light control, and it can be used with incandescent, fluorescent, and magnetic low-voltage ballasts, as well as electronic and magnetic ballasts. The ODS10-IQE has a range of up to 2100 square feet and a time-out delay of up to 30 minutes. It also features an ambient light override that allows you to set the light level at which the sensor will turn the lights on.

WARNINGS AND CAUTIONS:

• TO AVOID FIRE, SHOCK, OR DEATH; TURN OFF POWER AT CIRCUIT BREAKER OR FUSE AND TEST THAT THE POWER IS OFF BEFORE WIRING!

• DO NOTcontrolaloadinexcessofthespeciedratings.Damagetotheunit,re,electricshock,personalinjuryordeathcanoccur.

Checkyourloadratingstodeterminesuitabilityforyourapplication.

• Tobeinstalledand/orusedinaccordancewithelectricalcodesandregulations.

• Ifyouarenotsureaboutanypartoftheseinstructions,consultanelectrician.

WARNINGS AND CAUTIONS:

• Donotinstallthisunittocontrolareceptacle.

• Donottouchthesurfaceofthelens.Cleanoutersurfacewithadampclothonly.

• TheCat.No.ODS10-IQoccupancysensorisintendedtoreplaceastandardlightswitch.

• UsethisdeviceONLY WITH COPPER OR COPPER CLAD WIRE.

SinglePole(OneLocation)orMulti-Location

Designer Wall Switch Occupancy Sensor

Cat. No. ODS10-IQ

Incandescent - 800W-6.67A@120V-Fluorescent -1200VA-10A@120V-Fluorescent -2700VA-10A@277V-Supplemental - 1/4hp-5.8A@120V

No Minimum Load Required

Compatiblewithelectronicandmagneticballasts,electronicandmagneticlow-voltageballasts,incandescentlamps,andfans.

INSTALLATION INSTRUCTIONS

TOOLS NEEDED TO INSTALL YOUR SENSOR

Slotted/PhillipsScrewdriver ElectricalTape Pliers

Cutters   SmallSlottedScrewdriver

LevitonCat.No.ODS10-IQ,DesignerWallSwitchOccupancySensor,

isdesignedtodetectmotionfromaheat-emittingsource(suchas

apersonenteringaroom)withinitseld-of-view(monitoredspace)

andautomaticallyswitchlightsONandOFF.Thecontrolledlightswill

remainONuntilnomotionisdetectedandthescheduledtime-delay

hasexpired.

Cat. No. ODS10-IQ is UL and cUL listed.

TheOccupancySensorsensesmotionwithinitscoverageareaof

2100sq.ft(195.1m

)maximumandcontrolstheconnectedlighting.

Thisisaself-containeddevicewhichprovidessensingandlight

control.TheOccupancySensorwillturnthelightsONwhenmotion

isinitiallydetected,andkeepthelightsONforaslongasmotionis

detected.

TheOccupancySensorusesasmallsemiconductorheatdetectorthat

residesbehindamulti-zoneopticallens.ThisFresnellensestablishes

dozensofzonesofdetection.Thesensorissensitivetotheheat

emittedbythehumanbody.Inordertotriggerthesensor,thesource

ofheatmustmovefromonezoneofdetectiontoanother.Thedevice

ismosteffectiveinsensingmotionacrossitseld-of-view,andless

effectivesensingmotiontowardsorawayfromitseld-of-view(refer

to Field-of-View diagrams).Keepthisinmindwhenselectingthe

installationlocation(refer to Field-of-View diagrams).

Notethatoccupancysensorsrespondtorapidchangesin

temperature,socareshouldbetakennottomountthedevice

nearaclimatecontrolsource(i.e.radiators,airexchanges,andair

conditioners).Hotorcolddraftswilllooklikebodymotiontothedevice

andwilltriggeritiftheunitismountedtooclose.It is recommended

to mount the Occupancy Sensor at least 6 ft. away from then

climate control source.Thedevicecanbemountedinasinglegang

wallbox.

Inaddition,itisalsorecommendedNOTtomounttheOccupancy

Sensordirectlyunderalargelightsource.Largewattagebulbs

(greaterthan100Wincandescent)giveoffalotofheatandswitching

thebulbcausesatemperaturechangethatcanbedetectedbythe

device.MounttheOccupancySensoratleast6ft.awayfromlarge

bulbs.Ifitnecessarytomountthedevicecloser,lowerthewattageof

thebulbdirectlyoverhead.

WARNING:TO AVOID FIRE, SHOCK, OR DEATH; TURN

OFF POWER atcircuitbreakerorfuseandtestthatpoweris

offbeforewiring!

Step 1

ONOFF

ONOFFONOFF

ONOFF

• Pulloffpre-cutinsulationfromsensorleads.

• Makesurethattheendsofthewiresfromthewallboxarestraight

(cut if necessary).

• Removeinsulationfromeachwireinthewallboxasshown.

Preparing and connecting wires:

9/16"

(1.4 cm)

Strip Gage

(measure bare

wire here)

Cut

(if necessary)

Step 3

INSTALLING YOUR SENSOR

NOTE:UsecheckboxeswhenStepsarecompleted.

Installing your Sensor – Single-Pole Application:

Step 4

Identifying your wiring application

(most common):

Step 2

WIRING SENSOR:

Connect wires per WIRING DIAGRAM as follows:Screwwireconnector

onclockwisemakingsuretherearenobareconductorsbelowthewire

connectors.Secureeachconnectorwithelectricaltape.

• GreenorbarecopperwireinwallboxtoGreenlead.

• LineHotwallboxwiretoBlacklead.

• LoadwallboxwiretoBluelead.

NOTE: Allow 1 minute for warm-up after connecting and energizing.

WIRING SENSOR 1:

Connect wires per WIRING DIAGRAM as follows:

• GreenorbarecopperwireinwallboxtoSensor1Greenlead.

• LineHot(common)wallboxwireidentied(tagged)whenremovingold

switchandFirsttravelerfromSensor2toSensor1Blacklead.

• SecondTravelerwallboxwirefromSensor2toSensor1Bluelead.

WIRING SENSOR 2:

Connect wires per WIRING DIAGRAM as follows:

• GreenorbarecopperwireinwallboxtoSensor2Greenlead.

• Loadwallboxwireidentied(tagged)whenremovingoldswitchand

SecondTravelerfromSensor1toSensor2Bluelead.

• FirstTravelerLineHotfromSensor1toSensor2Blacklead.

NOTE: Allow 1 minute for warm-up after connecting and energizing.

NOTE: TheCat.No.ODS10-IQrequiresagroundwiretooperate

properly.Ifthereisnogroundwire,ensureelectricalboxisgroundedand

attachgroundwiretoboxwithascrew.Ifthegroundwireisoatingthis

devicewillnotwork.

NOTE: TheCat.No.ODS10-IQrequiresagroundwiretooperate

properly.Ifthereisnogroundwire,ensureelectricalboxisgroundedand

attachgroundwiretoboxwithascrew.Ifthegroundwireisoatingthis

devicewillnotwork.

NOTE:EithersensorcanturnthelightsON.Bothsensorsmusttimeout

toOFF.

DESCRIPTION

DI-02X-ODS10-00A

• AutoON/AutoOFF

• Leviton’sDecora

styledesign

• Switcheselectronicballasts

• LowProle,tamper-resistantlens

• AmbientLightOverride

FEATURES

3-Way

1. LineorLoad(Seeimportant*instruction)

2. Ground

3. FirstTraveler–notecolor

4. SecondTraveler–notecolor

Single-Pole

1.Line(Hot)

2.Ground

3.Load

IMPORTANT:For3-Wayapplications,notethatoneofthescrew

terminalsfromtheoldswitchbeingremovedwillusuallybeadifferent

color(Black)orlabeledCommon.Tagthatwirewithelectricaltapeand

identifyasthecommon(LineorLoad)inbothswitchwallboxes.

Step 5

Installing your Sensor – 3-Way Wiring Application:

NOTE:Dresswireswithabendtorelievestresswhenmounting

device.

•

 Positionallwirestoprovideroominoutletwallboxfordevice.

• Partiallysecuredeviceusinglongmountingscrewsprovided.

• Restorepoweratcircuitbreakerorfuse.

NOTE:ToavoidPERMANENTDAMAGEtotheunit,becareful

NOTTOOVERTURNthecontrolknobsorleverswhensettingthe

Sensor.Thecontrolscanbeaccessedbyremovingthewallplate

(ifapplicable)andcontrolpanelcover(refer to Control Panel

Diagram).Useasmallstraightbladescrewdrivertoadjustknobs

andandangertoadjusttheblinderlevers.

NOTE: DO NOT pressinonblinderleversoruseexcessiveforce

(refer to Control Panel Diagram).

• AttachtheControlPanelcoverwhenthedesiredsettingsare

complete.

If lights do not turn ON, refer to the TROUBLESHOOTING section.

Testing your Sensor prior to completely

mounting in wall box:

Step 6

Device Mounting:

TURN OFF POWER AT CIRCUIT

BREAKER OR FUSE.

Step 7

Restore Power:

Restorepoweratcircuitbreakerorfuse.

Installation is complete.

LeavetheroomandthelightswillturnOFFafterthe

selectedtime-outexpires.

Step 8

Installationmaynowbecompletedbytightening

mountingscrewsintowallbox.Attachwallplate.

Hot (Black)

Neutral (White)

Load

Sensor

Black

White

Blue

Green

Ground

Line

120-277VAC

50/60 Hz

Hot

(Black)

Neutral (White)

Load

Blue

Black

Green

Ground

Black

White

Black

Line

120-277VAC

50/60 Hz

Green

Ground

Sensor 2

Sensor 1

AutoON/AutoOFF:ThisdeviceisfactorysettooperateinAutoON/Auto

OFFmode.Thepushbuttonhasbeendisabledtopreventtheuserfrom

manuallycontrollingthelights.InAutoON/AutoOFFmodethelightswill

automaticallyturnONwhenmotionisdetected.Intheabsenceofmotion,

afterthetimeoutexpires,thelightswillturnOFF.

SETTINGS

OPERATION

• Fortechnicalassistancecontactusat1-800-824-3005

• Visitourwebsiteatwww.leviton.com

PRODUCT INFORMATION

DI-02X-ODS10-00A

©2012LevitonMfg.Co.,Inc.

Control Panel Cover

Blinder

Adjustment

Levers

BLINDERS

Range

Light

Time

Slash Mark

Control Panel Diagram

FCC COMPLIANCE STATEMENT

ThisdevicecomplieswithPart15oftheFCCRules.Operationissubjecttofollowing

twoconditions:(1)thisdevicemaynotcauseharmfulinterference,and(2)this

devicemustacceptanyinterferencereceived,includinginterferencethatmaycause

undesiredoperationofthedevice.

ThisequipmenthasbeentestedandfoundtocomplywiththelimitsforaClassB

DigitalDevice,pursuanttoPart15oftheFCCRules.Theselimitsaredesigned

toprovidereasonableprotectionagainstharmfulinterferenceinaresidential

installation.Thisequipmentgenerates,uses,andcanradiateradiofrequency

energyand,ifnotinstalledandusedinaccordancewiththeinstructions,maycause

harmfulinterferencetoradiocommunications.However,thereisnoguaranteethat

interferencewillnotoccurinaparticularinstallation.Ifthisequipmentdoescause

harmfulinterferencetoradioortelevisionreception,whichcanbedeterminedby

turningtheequipmentOFFandON,theuserisencouragedtotrytocorrectthe

interferencebyoneormoreofthefollowingmeasures:

• ReorientorrelocatethereceivingAntenna.

• Increasetheseparationbetweentheequipmentandthereceiver.

• Connecttheequipmentintoanoutletonacircuitdifferentfromthattowhichthe

receiverisconnected.

• Consultthedealeroranexperiencedradio/tvtechnicianforhelp.

FCC CAUTION

AnychangesormodicationsnotexpresslyapprovedbyLevitonManufacturingCo.,

Inc.,couldvoidtheuser'sauthoritytooperatetheequipment.

LIMITED 5 YEAR WARRANTY AND EXCLUSIONS

LevitonwarrantstotheoriginalconsumerpurchaserandnotforthebenetofanyoneelsethatthisproductatthetimeofitssalebyLevitonisfreeofdefectsinmaterialsandworkmanshipundernormalandproperuseforveyearsfromthepurchasedate.Leviton’sonlyobligationistocorrectsuchdefectsbyrepairorreplacement,atitsoption,ifwithinsuchveyearperiodtheproductisreturnedprepaid,with

proofofpurchasedate,andadescriptionoftheproblemtoLeviton Manufacturing Co., Inc., Att: Quality Assurance Department, 201 North Service Road, Melville, New York 11747.Thiswarrantyexcludesandthereisdisclaimedliabilityforlaborforremovalofthisproductorreinstallation.Thiswarrantyisvoidifthisproductisinstalledimproperlyorinanimproperenvironment,overloaded,misused,opened,

abused,oralteredinanymanner,orisnotusedundernormaloperatingconditionsornotinaccordancewithanylabelsorinstructions.There are no other or implied warranties of any kind, including merchantability and ﬁtness for a particular purpose,butifanyimpliedwarrantyisrequiredbytheapplicablejurisdiction,thedurationofanysuchimpliedwarranty,includingmerchantabilityandtnessfor

aparticularpurpose,islimitedtoveyears.Leviton is not liable for incidental, indirect, special, or consequential damages, including without limitation, damage to, or loss of use of, any equipment, lost sales or proﬁts or delay or failure to perform this warranty obligation.Theremediesprovidedhereinaretheexclusiveremediesunderthiswarranty,whetherbasedoncontract,tortorotherwise.

TROUBLESHOOTING

1. Ifthereisnoresponsefromtheunit(thelightneverturnsONandthe

LEDneverblinks)11/2minutesafterpowerisapplied,thenuninstall

deviceandverifythereisagroundconnectionatthewallbox.Ifthere

isagroundconnection,verifywiring.

2. IfthelightsneverturnON,buttheLEDblinks,checkiftheAmbient

LightControlKnobispointedfullycounter-clockwise(CCW).Rotateit

clockwise(CW)untilthelightsturnON.

3. IfthelightsconstantlystayON,evenwhentheroomisunoccupied:

 A.ChecktheTimesetting.Seehowthistimecomparestohowlong

thelightsstayON.

 B.TryloweringtheRangeControl.RotatetheknobCCWabout30˚.

 C.Iftheproblempersists,tryreducingagain.Note:DoNotreduceso

muchthatCat.No.ODS10-IQcannotseenormaloccupancy.

 D.BesuretousetheBlinderstoblockanyunwantedhallwaytrafc.

 E.Checkforreectedheat/motionasSensorUnitmaybeseeing

motionthroughawindow.

 F.CheckforadjacentHVACand/orheaterducts.

4. ForadditionalinformationcallLeviton’sTechnicalSupportLine.

Side (Vertical) Field - of - View

27 ft.

(8.2 m)

38 ft.

(11.7 m)

4 ft.

(1.2 m)

4.5 ft.

(1.4 m)

8.3

Sensor Unit

Field - of - View (Horizontal)

60 ft. (18.3 m)

40 ft. (12.2 m)

30 ft. (9.1 m)

20 ft. (6.1 m)

BLINDERS:Theblinderscannarrowtheeld-of-viewofthedeviceto

preventunwantedactivationfromtrafcinadjacentspace.Thereare

twoblinders,andeachoperateindependently.Tooperatetheblinders,

useangerorsmallscrewdrivertomovetheblinderadjustmentlevers

towardorawayfromthecenterofthedevice.

Theblinderleversarefoundabovethecontrolknobsandbelowthetext

‘BLINDERS’onthecontrolpanel.Withbothleversmovedfullytowards

thecenter,theeld-of-viewisnarrowedto60°.Withbothleversmoved

fullyawayfromthecenter,theeld-of-viewisatamaximum180°(refer

to Control Panel Diagram

TIME-DELAY:Cat.No.ODS10-IQwillturnlightsONwhenmotionis

detected.Whenmotionisnolongerdetected,theSensorUnitwillwait

acertainamountoftimeandthenturnthelightsOFF.Thiswaittimeis

called‘time-out’.

The“time-out”isselectedfromfour(4)presetvalues.Pointingthe

arrowatoneofthemarkingsonthefacechoosesthevalueoftime.The

followingselectionsareavailable:

Face Marking Value of Time

(/)SlashMark 30secondxedtime-outusedforperforminga

walk-test.

1  10minutetime-out

2  20minutetime-out

3  30minutetime-out

The “time-out” is factory preset to ten (10) minutes. Refer to ﬁgure 2A.

NOTE:Alltimedurationsmentionedintheinstructionsareapproximate

within10seconds.

AMBIENT LIGHT: TheAmbientLightLevelistheamountoflight

presentinaroomwithoutanyarticiallightadded.Ifthereisalready

enoughlightinaroom,theoccupantmaynotneedfurtherarticiallight.

Cat.No.ODS10-IQhasanadjustmenttokeepthelightsfromturning

ONifthereisenoughlightalreadypresent. The adjustment should be

made when the ambient light is at the level where artiﬁcial light is

needed.Followthesestepstomakeamoreaccurateadjustmentofthe

LightControl.

FEATURES

1.WiththelightsON,rotatetheTimeControlfullycounter-clockwise

(CCW)tosetthetime-outtothethirty(30)secondtestmode(refer

to Control Panel Diagram

2.RotatetheLightControlfullyCCW.

3.CovertheSensorUnitwithanopaquematerial,orleavetheroom

andlettheSensorUnittime-outandturnthelightsOFF.

4.RotatetheLightControlclockwise(CW)slowly,untilthelightturns

ON.Thisisthesettingforthecurrentleveloflightintheroom.

5.Adjustmentsarenished.

Manual ON Mode (N/A on this sensor):Themanualoverridebutton

onthesensorhasbeendeactivatedandwillnotcontrolthelights.

IfthelightcontrolisinthefullyCWposition,thelightswillturnON

whenevermotionisdetected,eveninfulldaylight.Intermediate

settingswillcausethelightstoturnONonlywhentheambientlightis

belowthelevelselectedbythelightcontrol.

NOTE:WhenthesettingisattheminimumCCWlevel,thelightswill

stayOFFwhentheroomisdim.Whenthesettingisatthemaximum

levelclockwise(CW),thelightswillturnONwhentheroomisbright.

NOTE:Theambientlightinaroomwillchangewiththetimeofday

andtheseasonoftheyear.

RANGE:Todecreasedetectionrangeandsensitivity,rotatetheknob

CCW(refer

to Control Panel Diagram

).Thedetectionrangecanbe

adjustedfrom100%downto36%.

Control Panel

Cover

Push Button

(Disabled)

Lens

Mounting Yoke

LED

Window

Bottom

Blinders

Leviton ODS10-IQE Installation guide

Brand: Leviton

Model: ODS10-IQE

Category: Motion detectors

Type: Installation guide

This manual is also suitable for

ODS10-IQI

Download PDF

report

Leviton ODS10-IQE Installation guide

This manual is also suitable for

Leviton ODS10-IQE Installation guide

Related papers

Other documents