Page is loading ...
Posh Solus Concealed S Trap & P Trap Link Toilet Suite
Plumbing Socket Set
Wrench
Tools Required
Page 01
Installation Instructions
Tools Required
Main Body x1 Cover Plate x1 Handle x1
A B C D E F
Screw x2 Anchor x2 Allen Key x1
F
Allen Key x1
Main Body x1 Cover Plate x1 Handle x1 Screw x2 Anchor x2 Allen Key x1
A B C D E F
Wrench Plumbing Socket Set
TBA
9
6
5
4
1
8
7
3
2
Number Part
MIZU SILK SHOWER MIXER - 9510746
Quantity Chrome Matte
Black
Brushed
Nickel
Brushed
Gun
Metal
1-3
4
5
6-8
9
Mixer Handle Set Complete 2265003
2265020
2265024
2265016
2265002
2265019
2265023
2265015
2265001
2265018
2265022
2265014
2265000
2265017
2265021
2265013
1
Concealed Wall Mixer Cap
Concealed Wall Mixer Cartridge Sleeve
Concealed Shower Mixer Plate Set
Allen Key 2.5mm
1
1
1
1
x
x
x
x
x
x
xxx
x
x
x
x
x
x
x
x
x
x
x
*
1
2
4
5
The installation of this Toilet Suite shall be in line with the normal minimum requirements in
AS/NZS 3500
Position pan onto pan connector and mark off position of pan fixing holes.
Remove pan and drill holes in position marked.
Apply flexible sealant to base of pan and carefully position pan onto pan connector and screw pan into pre-drilled
holes using corrosion resistant screws (not supplied).
Remove excess sealant.
Installation Instructions - Pan & Cistern
1.
2.
3.
4.
Posh Solus Concealed S Trap & P Trap Pan
150
375
445
370
270
Ø15
Ø8
1. Position pan onto pan connector and mark off position of pan fixing holes.
2. Remove pan and drill holes in position marked.
3. Apply flexible sealant to base of pan and carefully position pan onto pan connector and screw pan into pre-
drilled
holes using corrosion resistant screws (not supplied).
4. Remove excess sealant.
5. Place suite in position. Mark out the fixing holes
for the cistern.
Important! For timber stud and non-structural walls, the cistern should be fixed to a noggin or solid
wall.
6. If required, modify flush pipe to fit pan and cistern.
Note: The inlet valve can be changed from right to left hand side. Right side position supplied.
7. To install the link piece, flush pipe and seat, refer to the instructions below.
Position pan onto pan connector and mark off position of pan fixing holes.
Remove pan and drill holes in position marked.
Apply flexible sealant to base of pan and carefully position pan onto pan connector and screw pan into pre-drilled
holes using corrosion resistant screws (not supplied).
Remove excess sealant.
Place suite in position. Mark out the fixing holes for the cistern.
If required, modify flush pipe to fit pan and cistern.
Note: The inlet valve can be changed from right to left hand side. Right side position supplied.
To install the link piece, flush pipe and seat, refer to the instructions below.
For timber stud and non-structural walls, the cistern should be fixed to a noggin or solid
wall.
1.1.
3.
4.
5.
7.
2.
6.
For timber stud and non-structural walls, the cistern should be fixed to a noggin or solid
wall.
Posh - Solus Concealed S Trap & P Trap Link Toilet Suite of 02
Posh - Solus Concealed S Trap & P Trap Link Toilet Suite of 02
Installation Instructions - Toliet Seat & Link
1 2
Fit plastic bolts and slide nuts onto seat. Position seat onto pan and align correctly.
4 5
7 8
10
Once flush pipe has been cut to correct length,
lubricate and fit keeseal to pipe. Mount cistern
onto wall at recommended height. Once this is
done, fit and tighten plastic flush pipe nut.
Slide plastic link piece over flush pipe nut until
it locks into position.
Cut off as per distance (L) less 10mm.
Reinstall link piece.
Reposition seat back onto pan and slightly
tighten seat fixing bolts.
Fully tighten bolts to lock seat and link into
position. Ensure all connections are secure
and water tight.
Installation Instructions
1 2 3
4 5 6
7 8 9
10
Fit plastic bolts and slide nuts onto seat Position seat onto pan and align correctly
Draw line across back edge of the seat
hinge. Platform and remove seat.
Once flush pipe has been cut to correct
length, lubricate and fit keeseal to pipe.
Mount cistern onto wall at recommended
height. Once this is done, fit and tighten
plastic flush pipe nut.
Slide plastic link piece over flush pipe nut
until it locks into position
Mark off line on link piece to align with
previously drawn line (Diagram 3)
Cut off as per distance (L) less 10mm.
Reinstall link piece
Reposition seat back onto pan and
slightly tighten seat fixing bolts Slide/position seat into link piece
Fully tighten bolts to lock seat and link
into position. Ensure all connections are
secure and water tight.
Published 28/07/2023
Plumbers, please ensure a copy of the installation
instruction is left with the end user for future reference.
We recommend the use of soapy water or approved cleaners. This product should not be cleaned with abrasive materials. Damage caused by
any improper treatment is not covered by the product warranty. Refer to Warranty Conditions
3
Draw line across back edge of the seat hinge.
Platform and remove seat.
6
9
Mark off line on link piece to align with
previously drawn line (Diagram 3).
Slide/position seat into link piece.
Page 02
/
