Posh 1703112 Installation guide

Brand: Posh

Model: 1703112

Type: Installation guide

This manual is also suitable for

1703113

Plumbers, please ensure a copy of the installation

instruction is left with the end user for future reference.

of 06

Posh - Solus Freestanding Baths With/Without Overflow of 02

Installation Instructions

A B

Page 1 of 2

Plumbers, please ensure a copy of the installation

instructions is left with the end user for future reference.

Roca Inspira Round Above Counter Basin

370mm x 370mm

Plumbers, please ensure a copy of the installation instructions

is left with the end user for future reference

169

140

ø370

150

610

795

870

169

140

150

610

795

870

150

140

169

ø370

ø35

425 min

60 min

230 min

155 min

230 min

ø120

1 2 3 4

INSTALLATION INSTRUCTIONS

A3275L0

Ø120

A32768J/

[mm]

60 min.

Ø35

230 min.

170

425 min. 485 min.

170 min. 1 2 3 4

SAP - 1304517 - c

A3275L1

100mm

Jigsaw

Roca Inspira Round Above Counter Basin

370mm x 370mm

Installation Instructions

Roca Inspira Light Above Counter Basin 370mm

Disclaimer: Products in this specification manual must by regulation be installed by licensed and

registered trade people. The manufacturer/distributor reserves the right to vary specifications or

delete models from their range without prior notification. Dimensions are nominal measurements only.

Dimensions and set-outs listed are correct at time of publication however the manufacturer/distributor

takes no responsibility for printing errors.

Published 06/07/2021

Specification Sheet

Roca Inspira Square Above Counter Basin

370mm x 370mm Matte White

Dimensions are nominal measurements only.

To see the complete Roca range go to

www.reece.com.au

SPECIFICATIONS

Recommended Use Domestic, Hotel & Commercial

Basin Colour White

Basin Finish Matte

Material FINECERAMIC®

Mounting Countertop

Overflow Configuration No Overflow

Taphole Configuration No Taphole

Bowl Capacity 14.5L

Weight 6.1kg

Plug & Waste Size Open Waste

Plug & Waste Sold Separately

Tapware Sold Separately

WARRANTY

Warranty - Domestic Use 10 Years

Spare Parts & Labour 12 Months

Please refer to Warranty Page for full Terms and Conditions

CLEANING RECOMMENDATIONS:

We recommend the use of soapy water or approved cleaners. This product should not be cleaned with abrasive materials.

Damage caused by any improper treatment is not covered by the product warranty. Refer to Warranty Conditions

1806219

Page 1 of 1

140

169

370

ø46

Installation Instructions

Roca Inspira Round Above Counter Basin

370mm x 370mm

Roca Inspira LightSoft Square Above Counter Basin 500mmx370mm

Posh Solus Freestanding Baths

With/Without Overflow

1. Install waste pipe in accordance with the set out (Diagram A). Check the waste pipe will align accurately with

bath waste. It may be necessary to use a flexible coupling or length of unrestrained waste pipe to absorb strain

on the bath due to misaligned waste setup see (Diagram C).

2. This bath is not self supporting and does require a support at the base via masonry, steel or timber. It is

important that the full rim of the bath rests on a support wall constructed from wood, masonry or steel. If the

bath is to be checked into the wall then a batton should be securely bolted to the wall to provide

support (Diagram B and C).

3. Place bath in position and connect waste. Fill bath and then release, checking seals for leaks and that the bath

drains successfully.

4. Apply flexible sealant to the exposed edges.

5. Enclose and tile in bath.

Please check surface thoroughly before installing. Installation of the bath will be taken as

acceptance of the product. Also, it is important to install the product in accordance with the

installation instructions below.

Installation Instructions

Diagram A

Posh Bristol Enamelled Pressed Steel Inset Bath

Page 01

Please check surface throughly before installing.

Installation of the bath will be taken as acceptance of

the product. Also, it is important to install the product

in accordance with this installation instruction.

570 mm

1200 1500 1600 1700

700 700 700 700

375 390 390 390

70 70 70 70

65 65 65 65

290 290 290 290

1500

750

375

105

310

1700

750

375

110

330

Prior To Installation

Please unwrap the bath and check it carefully to ensure it has not been damaged in

handling or transport.

Please check that all parts have been supplied.

Assemble bath on a mat to protect against damage to bath surface.

Please do not remove the old ﬁxture before you unpack and inspect the new unit.

Store the bath in a safe place until you begin installation to avoid damage.

Any installation should be carried out by a qualiﬁed tradesman with knowledge of

statutory plumbing requirements in your area.

This installation guide does not include details of waste connection; ﬁnal decision

about installation of waste connection should be taken by a suitably qualiﬁed

person.

Please check surface throughly before installing.

Installation of the bath will be taken as acceptance of

the product. Also, it is important to install the product

in accordance with this installation instruction.

AED

ŸInstall waste pipe in accordance with the diagram. Check waste

pipe to ensure alignment with bath waste.

ŸThis bath is not self supporting and does require a support at the

base via Masonry, Steel or Timber (1).

Note: It may be necessary to use a flexible coupling or length

of unrestrained waste pipe to absorb strain on the bath due

to misaligned waste setup.

Note: If the bath is to be checked into the wall then a batten

should be securely bolted to the wall to provide support.

1200

1500 1600 1700 1500 1700

700

360

290

700

390

290

700

390

290

700

390

290

750

390

290

750

390

330

The installation of this Toilet Suite shall be in line with the normal minimum requirements in

AS/NZS 3500

The installation of this Toilet Suite shall be in line with the normal minimum requirements in

AS/NZS 3500

• Please unwrap the bath, check it carefully for any damage at the point of delivery when received.

• Check that all parts have been supplied.

NOTE: Installation is deemed as acceptance. No consideration for any damage claim will be considered

once bath is fully installed.

• All waste and plumbing should be determined by the licensed plumber to accommodate site conditions.

• Install waste pipe and trap - taking into consideration the waste position of the bath. Make sure that the surface

where the bathtub will be placed is perfectly flat, free of any excess humidity and offers adequate support.

• The bath should be supported by the legs, not by the rim. Adjust the feet to level and support bath from base.

• Ensure all adjustable bath feet are level and load bearing. this can be done by using a spirit level on a flat surface

on the top of the bath. Check the bath is level along each axis.,

• To make any height adjustments, the bath feet can be rotated to raise or lower the feet. Adjust bath feet until bath

is 3mm above the floor and once bath is level and the feet are in the correct position, the locking nut can be

tightened with a spanner to prevent the feet from moving further.

• Measure the location of the bathtub feet in relation to the desired installation position. Mark on the floor the

location of the feet and use a marking pencil to draw a bath outline on the floor around the bath base.

• Lift and tilt bath up on it’s side and fit the waste. Water test the bath to check that it is draining correctly without and

leaks.

• Silicone seal the bath with the corner wall and in position onto the floor and into 3mm gap between base of bath

and floor to seal it. Allow seal to fully cure for 24 hours before use.

• A suggested bath component list for Slab floor or 2nd storey bath connection or Timber floor with clear access

underneath is listed on the next page:

Installation

TBA

• Only a qualified tradesperson with knowledge of statutory plumbing requirements in accordance

with AS/NZS 3500 should carry out the installation of the bath's water connections.

• Please unwrap the bath and check it carefully to ensure it has not been damaged in handling or

transport.

• Please check that all parts have been supplied.

• Assemble the bath on a mat to protect against damage to the bath surface.

• Please do not remove the old fixture before you unpack and inspect the new unit.

• Store the bath in a safe location until you begin installation to avoid damage.

• This installation guide does not include a detailed procedure for the waste connection; a suitably

qualified person should advise on the best installation final decision about the installation of the

waste connection.

• The Installer must ensure that the waste utilise has a sufficient amount of thread to carry out

plumbing connections.

• If the bath has an overflow, ensure an overflow compatible waste is used that can maintain an

acceptable overflow rate.

• Install waste pipe and trap - considering the bath's waste position. Make sure that the surface where the bathtub

will be placed is perfectly flat, clean, free of moisture and offers adequate support.

• Ensure all adjustable bath feet are level and are in a load-bearing position.

• To make height adjustments, the bath feet can be rotated to raise or lower the feet.

• Adjust the bath feet until the bath is 3mm above the floor, and once the bath is level and the feet are in the correct

position, the locking nut can be tightened with a spanner to prevent the feet from moving further.

• Measure the bathtub feet' location relative to the desired installation position. Mark on the floor the location of the

feet and use a marking pencil to draw a bath outline on the floor around the bath base.

• Check that the bath is level along the top and bottom.

• Lift and tilt the bath up on its side and fit the waste. Water test the bath to check that it drains correctly without any

leaks.

• Seal the bottom of the bath with silicone into a 3mm gap between the base of the bath and the floor. Allow the

silicone to cure before use fully.

Only a qualified tradesperson with knowledge of statutory plumbing requirements in accordance

with AS/NZS 3500 should carry out the installation of the bath's water connections.

• Unwrap the bath and check it carefully to ensure it has not been damaged in handling or transport.

• Check that all parts have been supplied.

• Assemble the bath on a mat to protect against damage to the bath surface.

• Ensure you do not remove the old fixture before you unpack and inspect the new unit.

• Store the bath in a safe location until you begin installation to avoid damage.

• This installation guide does not include a detailed procedure for the waste connection; a suitably

qualified person should advise on the best installation final decision about the installation of the waste

connection.

• The Installer must ensure that the waste utilised has a sufficient amount of thread to carry out plumbing

connections.

• If the bath has an overflow, ensure an overflow compatible waste is used that can maintain an acceptable

overflow rate.

Plumbers, please ensure a copy of the installation

instruction is left with the end user for future reference.

of 06

Posh - Solus Freestanding Baths With/Without Overflow of 02

Installation Instructions

We recommend the use of soapy water or approved cleaners. This product should not be cleaned with abrasive materials. Damage caused by any

improper treatment is not covered by the product warranty - refer to Warranty Conditions.

Care Details

Plumbers, please ensure a copy of the installation

instruction is left with the end user for future reference.

Care Details

Diagram B

Diagram C

Published 15/08/2023 Page 02

Wall

Tiles

Wet area

Sheeting

Flexible Sealant

Bath

Masonry, wood

or steel bath

support

ŸPlace Bath (2) in position and connect waste. Fill Bath and then

release.

Note: Check seals for leaks and that the bath drains

successfully.

ŸApply Flexible Sealant (6) to the exposed edges.

ŸEnclose and Tile (7) in Bath (2).

Wet area

Sheeting

Cement/

Glue

Ÿ1. : Slab floor or 2nd storey suggested waste installation method.

-1405525 DWV Adaptor PVC X FI 40mm

-1400105 40mm DWV PVC pipe (installer to cut to length)

-Slab floor or 2nd storey bath connection

1. Install waste pipe in accordance with the set out (Diagram A). Check the waste pipe will align accurately with

bath waste. It may be necessary to use a flexible coupling or length of unrestrained waste pipe to absorb strain

on the bath due to misaligned waste setup see (Diagram C).

2. This bath is not self supporting and does require a support at the base via masonry, steel or timber. It is

important that the full rim of the bath rests on a support wall constructed from wood, masonry or steel. If the

bath is to be checked into the wall then a batton should be securely bolted to the wall to provide

support (Diagram B and C).

3. Place bath in position and connect waste. Fill bath and then release, checking seals for leaks and that the bath

drains successfully.

4. Apply flexible sealant to the exposed edges.

5. Enclose and tile in bath.

ŸUnwrap the bath and check it carefully to ensure it has not been damaged in handling or transport.

ŸCheck that all parts have been supplied.

ŸAssemble bath on a mat to protect against damage to bath surface.

ŸDo not remove the old fixture before you unpack and inspect the new unit.

ŸStore the bath in a safe place until you begin installation to avoid damage.

ŸAny installation should be carried out by a qualified tradesman with knowledge of statutory plumbing

requirements in your area.

ŸThis installation guide does not include details of waste connection; final decision about installation of

waste connection should be taken by a suitably qualified individual.

Below floor smart trap

2. Timber floor with clear access underneath:

Connection of bath waste to 40mm P-Trap in timber sub-floor is acceptable when clear access is available

under the floor.

-1409115 Dura Standard P Trap 40mm or 1409121 Dura Short P Trap 40mm

-1400105 40mm DWV PVC pipe (installer to cut to length)

-Timber floor with clear access underneath

Below floor smart pan Waste pipe into smart seal

P-Trap

• Install waste pipe and trap - taking into consideration the waste position of the bath. Make sure that the surface

where the bathtub will be placed is perfectly flat, free of any excess humidity and offers adequate support.

• Ensure the corner wall where the corner bath will be against is straight so bath can locate right into the corner, or

this bath type cannot be installed.