Posh 9512231 Installation guide

Posh
Brand
Posh
Model
9512231
Type
Installation guide
Plumbing Socket Set
Wrench
Tools Required
Page 01
Tools Required
Main Body x1 Cover Plate x1 Handle x1
A B C D E F
Screw x2 Anchor x2 Allen Key x1
F
Allen Key x1
Main Body x1 Cover Plate x1 Handle x1 Screw x2 Anchor x2 Allen Key x1
A B C D E F
Wrench Plumbing Socket Set
TBA
9
6
5
4
1
8
7
3
2
Number Part
MIZU SILK SHOWER MIXER - 9510746
Quantity Chrome Matte
Black
Brushed
Nickel
Brushed
Gun
Metal
1-3
4
5
6-8
9
Mixer Handle Set Complete 2265003
2265020
2265024
2265016
2265002
2265019
2265023
2265015
2265001
2265018
2265022
2265014
2265000
2265017
2265021
2265013
1
Concealed Wall Mixer Cap
Concealed Wall Mixer Cartridge Sleeve
Concealed Shower Mixer Plate Set
Allen Key 2.5mm
1
1
1
1
x
x
x
x
x
x
xxx
x
x
x
x
x
x
x
x
x
x
x
*
1
2
4
5
Posh Solus Tile Over Shower Tray Rear Outlet
Posh Solus Tile Over Shower
Tray – Rear Outlet
Ensure these instructions are carefully read prior to installation. Failure to follow instructions will
void warranty.
Leaking joints are not covered by the warranty.
It is the responsibility of the installer of the Posh Solus Tile Tray to check with local building code in relation to
waterproofing and installation.
These Instructions are a recommended method only.
Installation should also be in accordance with relevant standards;
ŸAS 1684 - Residential timber farming and construction.
ŸAS 2870 - Slabs and footings.
ŸAS 1860 - Particle flooring/installation.
ŸAS 2269 - Plywood (Structural)
ŸAS 3740 - Waterproofing of domestic area.
ŸAS 3958 - Ceramic Tiles (all parts).
It is the responsibility of the installer to comply with relevant OH&S Regulations and to wear appropriate Personal
Protective Equipment as required.
TBA Posh - Solus Tile Over Shower Tray Rear Outlet of 14
Posh - Solus Tile Over Shower Tray Rear Outlet of 14
Index
Mixer must be installed to the requirements of AS/NZS 3500 by a qualified plumber. The mixers are
factory tested and sealed so as to give the best performance.
INSTALLATION TO TIMBER FLOORS
Ensure subfloor is sound and if required replace any timber that may be affected by weather damage or rotting. If
installing direct to floor joists ensure sub floor is strengthened as per Diagram1. Failure to follow these instructions
will void warranty.
INSTALLATION OF TILES TO TRAY
For direct gluing of tiles to tray, the manufacturer recommends epoxy adhesives, or similar product. Ensure tray is
clean from dirt and dust, using methylated spirits will assist in removing dust. Allow to dry before commencement of
installation.
CUTTING INSTRUCTIONS
If the tray needs to be cut down it is recommended to use a diamond saw blade only. Eye protection and dust mask
are also recommended. Only cut tray in a well-ventilated area or in the open.
HOB
Please note that the Hob is shown on the inside of the tray and this is the preferred method if using a shower
screen.
Note: Please read these instructions carefully prior to installation, failure to follow
instructions will void warranty.
Note: PLEASE READ THESE INSTRUCTIONS CAREFULLY BEFORE INSTALLING
FAILURE TO FOLLOW INSTRUCTIONS WILL VOID WARRANTY
It is the responsibility of the installer of the Posh Solus Tile Tray to check with local building code in relation to
waterproofing and installation. These instructions are a recommended method only. The installation of the puddle
flange and outlet is the responsibility of the installer to ensure a water tight seal between tray and puddle flange,
the manufacturer can only supply recommended methods of installation.
INSTALLATION TO TIMBER FLOORS
Ensure subfloor is sound and if required replace any timber that may be affected by weather damage or rotting. If
installing direct to floor joists ensure sub floor is strengthened as per diagram1. Failure to follow these instructions
will void warranty.
INSTALLATION OF TILES TO TRAY
For direct gluing of tiles to tray, the manufacturer recommends epoxy adhesives, or similar product. Ensure tray is
clean from dirt and dust, using methylated spirits will assist in removing dust. Allow to dry before commencement
of installation.
CUTTING INSTRUCTIONS
If the tray needs to be cut down it is recommended to use a diamond saw blade only. Eye protection and dust
mask are also recommended. Only cut tray in a well-ventilated area or in the open.
HOB
Please note that the Hob is shown on the inside of the tray and this is the preferred method if using a shower
screen.
It is the responsibility of the installer of the Posh Solus Tile Tray to check with local building code
in relation to waterproofing and installation. These instructions are a recommended method only.
The installation of the puddle flange and outlet is the responsibility of the installer to ensure a
water tight seal between tray and puddle flange, the manufacturer can only supply recommended
methods of installation.
1. Product Range............................................................Page 3
2. Installation Overview..................................................Page 4
3. Installation Detail........................................................Page 5
4. Trimming Overview.....................................................Page 7
5. Trimming Diagrams.....................................................Page 8
6. Waterproofing............................................................Page 10
7. Tiling...........................................................................Page 10
8. Adhesives and Waterproofing Products.................Page 11
9. Waste Outlet Connector............................................Page 12
10. Grates and Outlets..................................................Page 13
Page 02
Posh - Solus Tile Over Shower Tray Rear Outlet of 14
Installation
1
Page 03
1
2
52-77.5mm
Finished wall surface
G1/2" BSP INT
‘O’-ring
G1/2" BSP INT
Outlet to Shower,
Bath or Basin
Ø50 Tile Penetration
Wall Sheet lining
Waterproofing membrane
Important: Waterproofing/sealant
materials must not contact 1 & 2.
Important: Waterproofing/sealant
materials must not contact 1 & 2.
2
1
1/2" BSP
52-77.5mm Finished wall surface
Ø45-50 Wall Penetration
1/2" BSP
Outlet to Shower,
Bath or Basin
Wall Sheet lining
Important: Waterproofing/sealant
materials must not contact 1 & 2.
Waterproofing Zone
2
1
1/2" BSP
52-77.5mm Finished wall surface
Ø45-50 Wall Penetration
1/2" BSP
Outlet to Shower,
Bath or Basin
Wall Sheet lining
Important: Waterproofing/sealant
materials must not contact 1 & 2.
Waterproofing Zone
Flush out new pipe work prior to connecting the new
mixer.
During installation protect the exposed finish surface
by using the plastic protective cover provided. Please
pay attention to the minimum/maximum depth.
2
1
1/2" BSP
52-77.5mm
Ø45-50 Wall Penetration
1/2" BSP
Outlet to Shower,
Bath or Basin
Wall Sheet lining
Important: Waterproofing/sealant
materials must not contact 1 & 2.
Waterproofing Zone
Finished wall surface
1/2" BSP
52-77.5mm
1/2" BSP
Outlet to Shower,
Bath or Basin
Wall Sheet lining
Note: This tap is suitable for applications where both hot and
cold water supply pressures are at 150kPa - 500kPa.
Waterproofing and sealant materials are used to seal
against moisture or water penetration to ensure
integrity of the wall sheet lining structure. It must not
interfere with the removal of the protective cover and
installation of the mixer trim components. The
installing plumber is responsible for waterproofing
the shower mixer penetration AS 3740 -
Waterproofing of Domestic Wet Areas.
Waterproofing / sealant materials must be clear of the
Protective Cover (2) and the surface it protects (1) to
allow for removal of the protective cover and mixer
trim set for fit off.
Connect Mixer (1) to hot and cold Water Supply (3).
Connect shower pipework to the top outlet.
Pressure check all connections.
Leaking joints are not covered by the warranty.
1.
2.
3.
2
12
52-77.5mm Finished wall surface
1/2" BSP
Ø45-50 Wall Penetration
Wall Sheet lining
Waterproofing Zone
1/2" BSP
34.50mm
Centre base on joists to be trimmed out. Tile Tray can span no
greater than demonstrated. Failure to follow floor detail will void
warranty. Floor joists and trimmers must be flat, planning or
sanding off any ridges is recommended before installation. Trim
edges of base to support join of flooring and Tile Tray.
If the tray requires trimming it is recommended to use a diamond
saw blade in a well-ventilated area. It is recommended that
appropriate PPE is worn, such as eye protection and a dust
mask.
Ensure that the joists are level; the tile tray is designed with fall to
the drain. If the joists are not level this may distort the base and
affect the flow of water.
Tile tray must be supported around all edges with a maximum of
450mm centers.
Install base with adhesive; apply a continuous bead to the
underside of the tray. Ensure the adhesive has a clean surface to
adhere to. Always use a flexible adhesive when adhering to a
substrate e.g. Sikaflex-11FC.
After installation onto the substrate, apply downward pressure
and check the tile tray is level.
It is essential to test for water run off to the waste outlet prior to
commencing the installation of the shower walls and tiling. This
will ensure the tile tray is draining correctly. At times during
installation and airlock may occur within the plumbing which can
have an adverse effect on the drainage of the tile tray. If this
occurs, it is recommended to use a plunger to remove this
airlock.
Stud Frame – check in wall junction: The waterproof membrane
should extend at least 1500mm from centre of the tile tray outlet.
The fall of the floor outside the tile tray must be towards the tile
tray outlet to comply with local standards.
All the joints between the tray and the floor/walls must be
waterproofed using one of the approved waterproofing, tile
adhesive and grouting tiling system companies as recommended
by the tile tray manufacturer themselves.
Waterproof around the waste outlet and around membrane.
Rough up the surface of base using 80 grit sandpaper (only
spend 2-3 mins)
Apply primer over the tile tray surface and allow to dry as per
primer manufactures instructions.
Option to waterproof over primer but not necessary
1.
2.
3.
1.
2.
3.
1.
2.
3.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
1. Overview - Product Range
1703067
Posh Solus TT Waste Base Only 900x900
1703068
Posh Solus TT Waste Base Only 1200x900
1703073
Posh Solus TT Channel Base Only 900x900
1703085
Posh Solus TT Channel Base Only 1200x900
1703074
Posh Solus TT Channel Base Only 900x1200
1703096
Posh Solus TT Channel Base Only 1500 x 1000
FIGURE A:
Posh - Solus Tile Over Shower Tray Rear Outlet of 14
Page 04
TILE TRAY INSTALLATION
7
8
9
xxxx.
xxxx
xxxx
xxxx
12
12
Note: Tile Tray shown direct to joist, however same method
applies to any other suspended floor application.
Note: This method can be used for any application where access
under the floor is restricted and connection is difficult.
1.
7
8
16
STUD FRAME – NON-CHECK IN WALL JUNCTION
TILE TRAY WASTE CONNECTIONS
Remove Decorative Cover (4) and unscrew the Grub Screw (5)
using an allen key.
Lift off the Handle (6) and remove the Cartridge Dome (7),
unscrew the Brass Locking Nut (8).
Remove Cartridge Sleeve (9), Diverter Assembly (10) and
Back Plate (11).
Lift out the Cartridge (12).
Re-fit the Cartridge (12), Cartridge Sleeve (9), Diverter Assembly
(10), Back Plate (11), Locking Nut (8), Cartridge Dome (7)
and Handle (6).
Tighten Grub Screw (5) and push in Decorative Cover (4).
1.
2.
3.
4.
5.
6.
Centre base on joists to be trimmed out. Tile Tray can span no
greater than demonstrated. Failure to follow floor detail will void
warranty. Floor joists and trimmers must be flat, planning or
sanding off any ridges is recommended before installation. Trim
edges of base to support join of flooring and Tile Tray.
If the tray requires trimming it is recommended to use a diamond
saw blade in a well-ventilated area. It is recommended that
appropriate PPE is worn, such as eye protection and a dust
mask.
Ensure that the joists are level; the tile tray is designed with fall to
the drain. If the joists are not level this may distort the base and
affect the flow of water.
Tile tray must be supported around all edges with a maximum of
450mm centers.
14.
15.
16.
Stud Frame – check in wall junction: The waterproof membrane
should extend at least 1500mm from centre of the tile tray outlet.
The fall of the floor outside the tile tray must be towards the tile
tray outlet to comply with local standards.
Apply tile adhesive glue over the primer and down bed tiles into
position using the preferred tile spacing distance as per job
requirement (i.e.: 2mm or 4mm).
Allow tile adhesive to dry from minimum 24hrs prior to grouting.
Must Use sanded / cement- based grout to ensure structural
soundness and durability. Please refer to recommended
waterproofing, tile adhesive and sanded / cement- based
grouting tiling system companies as recommended by the tile
tray manufacturer themselves.
17.
SUSPENDED FLOOR
SLAB ON GROUND
SUSPENDED FLOOR
SLAB ON GROUND
Water Proof Sealant
Water Resistant Surface
Material over the wall
Water Resistant Sheeting
Battens or Sheeting to pack wall
to allow lip to fit behind water
resistant sheeting
Timber or
Steel Stud
Wall
Bottom Plate
Floor
Akril Tile Tray
Tile Adhesive
Floor Tiles
2. Installation Overview
2.1 Check out wall studs (A) as required.
2.2 For timber base Install support joists/trimmers (B) -
Refer Section 3.
For concrete base - Refer also Section 3.
2.3 Apply a continuous bead of adhesive (C) to the
underside perimeter of the tray.
Apply adhesive (C) to internal trimmers or concrete
base as appropriate.
Refer Section 8 for recommended adhesives
For concrete base use mortar or slurry.
2.4 Trim Tile tray as required - Refer Section 4 and 5.
2.5 Attach waste outlet to tile tray (D) - Refer Section 9.
2.6 Install tile tray - Refer Section 3.
2.7 Install wall sheeting (E)
Refer manufacturers installation instructions.
2.8 Install waterproofing (F) - Refer Section 6.
2.9 Install tile adhesive (G).
2.10 Install tiles (H). Refer Section 7.
2.11 Apply caulking material (I).
2.1 Check out wall studs (A) as required.
2.2 For timber base Install support joists/trimmers (B) -
refer Section 3
For concrete base –refer also Section 3.
2.3 Apply a continuous bead of adhesive (C) to the
underside perimeter of the tray.
Apply adhesive (C) to internal trimmers or concrete
base as appropriate.
Refer Section 8 for recommended adhesives
For concrete base use mortar or slurry.
B
A
C
D
E
D
D
F
G
H
I
FIGURE B:
Posh - Solus Tile Over Shower Tray Rear Outlet of 14
Stud Frame – Checked In-Wall Junction
1.
TILE TRAY WASTE CONNECTIONS
Tile Tray shower base can be installed on a 10mm mortar bed or glued to the floor with silicone. If installing on
silicone apply a continuous bead to the underside of the tray.
Ensure the silicone has a clean surface to adhere to
Ensure the area is level and will allow water to flow to outlet when tray is installed (tray has in-built fall to waste)
Ensure underside of tray has full support at all times (450mm square for direct to floor joist application)
INSTALLATION TO CONCRETE FLOOR
Ensure the area is level and will allow water to flow to outlet when tray is installed (tray has in-built fall to waste)
Tray can be installed on mortar bed if required
Void area around outlet can be no greater than 300m m x 300 mm
If installing on silicone apply a continuous bead to the underside of the tray. Ensure the silicone has a clean surface
to adhere to.
Refer to the installation instruction for smartseal outlet, it is recommended the smartseal be installed 30mm below
floor surface to allow for locking nut.
Smartseal to sit 30mm below concrete floor level
Note: Manufacturer recommends IPLEX Smart seal be used for new construction. If Smartseal is not used ensure
void area under waste outlet does not exceed 300x300 mm as the area around the waste outlet is designed to span
this distance.
300 X 300mm is MAXIMUM SPAN RECOMMENDED
TIMBER FLOOR INSTALLATION
3. Installation
Installation to Timber floor (Ground floor, 1st floor and above)
Preliminary
Ensure subfloor is sound and if required replace any timber that may be affected by weather damage or rotting.
Installing the tray - Refer also to installation diagrams – Figure D (Page 7)
*
3.1 Centre base on joists to be trimmed out. Tile Tray must be fully supported around all edges and also can span no
greater than demonstrated in Figure C (Page 6).
Failure to follow floor detail will void warranty. Floor joists and trimmers must be flat, planning or sanding off any
ridges is recommended before installation. Trim edges of base to support join of flooring and Tile Tray.
3.2 Ensure that the joists are level; the tile tray is designed with fall to the drain. If the joists are not level this may
distort the base and affect the flow of water.
3.3 Install Waste outlet connector - Refer Section 9.
3.4 Install base with adhesive; apply a continuous bead to the underside perimeter of the tray.
Apply adhesive to trimmers as appropriate.
Ensure the adhesive has a clean surface to adhere to.
Always use a flexible adhesive when adhering to a substrate (e.g. Sikaflex-11FC) - Refer Section 8.
3.5 After installation onto the substrate, apply downward pressure and check the tile tray is level.
Ensure adhesive is fully cured before continuing the installation.
3.6 It is essential to test for water run off to the waste outlet prior to commencing the installation of the waterproofing
and subsequent shower walls and tiling. This will ensure the tile tray is draining correctly. At times during
installation and airlock may occur within the plumbing which can have an adverse effect on the drainage of the tile
tray. If this occurs, it is recommended to use a plunger to remove this airlock.
Installation to Concrete Slab
Preliminary
Ensure the area is level and will allow water to flow to outlet when tray is installed
(NB : tray has in-built fall to waste).
Installing the tray - Refer also to installation diagrams - Figure D (Page 7)
3.7 Tray must be installed on mortar bed or slurry.
3.8 Void area around outlet can be no greater than 300mm x 300mm.
3.9 After installation onto the substrate, apply downward pressure and check the tile tray is level.
Ensure mortar/slurry is fully cured before continuing the installation.
3.10 It is essential to test for water run off to the waste outlet prior to commencing the installation of the waterproofing
and subsequent shower walls and tiling. This will ensure the tile tray is draining correctly. At times during
installation and airlock may occur within the plumbing which can have an adverse effect on the drainage of the tile
tray. If this occurs, it is recommended to use a plunger to remove this airlock.
Page 05
Posh - Solus Tile Over Shower Tray Rear Outlet of 14
HOBBED – TRAY INSTALLED DIRECT TO FLOOR
JOIST
HOBBED – TRAY INSTALLED ON CONCRETE OR
SHEET FLOORING
HOBLESS – TRAY INSTALLED DIRECT TO FLOOR
JOIST
HOBLESS – TRAY INSTALLED DIRECT TO
Concrete Floor
HOBLESS – TRAY INSTALLED DIRECT TO FLOOR JOIST
3. Installation (Cont’d)
FIGURE B: Floor Joist Detail (Typical)*
*NB; Minimum Joist/trimmer size = 90 x 35 F17
Page 06
900 x 900 1200 x 900
900 x 1200
1500 x 1000
200mm
200mm
200mm
200mm
200mm
200mm
200mm
350mm
350mm
350mm 350mm 450mm 450mm
330mm
330mm
330mm
350mm350mm
400mm
400mm
430mm 430mm 430mm 430mm
Posh - Solus Tile Over Shower Tray Rear Outlet of 14
Critical Dimension Check
GUARANTEE
Posh Solus Tile Tray comes with a ……………………
3. Installation (Cont’d)
4. Trimming - Overview
4.1 Trim edges of tile tray as required.
Refer trimming diagrams in Section 5 for
typical examples
It is recommended to use a diamond saw
blade in a well-ventilated area.
Ensure that appropriate PPE is worn,
such as eye protection and a dust mask.
4.2 Apply sealant at interface of the tile tray and the flooring/concrete.
4.3 Install waterstop and expansion joint at interface between tiles on the tray and tiles on the flooring/concrete.
4.4 Install waterproofing to conform to AS3740 –refer Section 6.
NB: A hob can also be incorporated if required
Hob is recommended to be placed on the Tile tray side of the interface.
4.1 Trim edges of tile tray as required.
Refer trimming diagrams in Section 5 for
typical examples
It is recommended to use a diamond saw
blade in a well-ventilated area.
Ensure that appropriate PPE is worn,
such as eye protection and a dust mask.
4.2 Apply sealant at interface of the tile tray and the flooring/concrete.
4.3 Install waterstop and expansion joint at interface between tiles on the tray and tiles on the flooring/concrete.
4.4 Install waterproofing to conform to AS3740 –refer Section 6.
NB: A hob can also be incorporated if required
Hob is recommended to be placed on the Tile tray side of the interface.
FIGURE D: (Detail Typical)
Checked In Not Checked In
Page 07
4.2 Apply sealant at interface of the tile tray and the flooring/concrete.
4.3 Install waterstop and expansion joint at interface between tiles on the tray and tiles on the flooring/concrete.
4.4 Install waterproofing to conform to AS3740 - Refer Section 6.
NB: A hob can also be incorporated if required
Hob is recommended to be placed on the Tile tray side of the interface.
4.1 Trim edges of tile tray as required.
Refer trimming diagrams in Section 5 for
typical examples.
It is recommended to use a diamond saw
blade in a well-ventilated area.
Ensure that appropriate PPE is worn,
such as eye protection and a dust mask.
Posh - Solus Tile Over Shower Tray Rear Outlet of 14
5. Trimming Diagrams - Typical Examples
Posh Solus Tile Tray Base: 25mm
Posh Solus Tile Tray Base: 25mm
Posh Solus Tile Tray Base: 25mm
5.1 –Example 1
Tile tray installation -Direct to joists (no rebate)
Tile tray trim -Full Trim
Floor Substrate -Floor sheeting and tile underlay
5.2 –Example 2
Tile tray installation -Direct to joists (no rebate)
Tile tray trim -Partial -cut down by 25mm
Floor Substrate -Floor sheeting and tile underlay
5.3 –Example 3
Tile tray installation -Direct to joists (no rebate)
Tile tray trim -Full Trim
Floor Substrate -Floor sheeting and tile underlay
or Floor sheeting and 18mm "Scion"
Page 08
“Water Stop”
Aluminium T Insert
25 x 25 x 1.6mm
Ceramic Tile: 8mm Ceramic Tile: 8mm
Tile Underlay: 6mm
Yellow Tongue: 20mm
Cut down 25mm
of tile tray upturn
9mm
“Water Stop”
Remaining 10mm of
tile tray upturn
Ceramic Tile: 8mm Ceramic Tile: 8mm
Tile Underlay: 6mm
Yellow Tongue: 20mm
“Water Stop”
Aluminium T Insert
25 x 25 x 1.6mm
Ceramic Tile: 8mm
Ceramic Tile: 8mm
Yellow Tongue: 20mm
“Step up to shower base”: 10mm
1mm layer of waterproofing
membrane installed over yellow
tongue
Posh - Solus Tile Over Shower Tray Rear Outlet of 14
5. Trimming Diagrams - Typical Examples (Cont’d)
Posh Solus Tile Tray Base: 25mm
Posh Solus Tile Tray Base: 25mm
Posh Solus Tile Tray Base: 25mm
5.4 –Example 4
Tile tray installation -Direct to concrete (30mm rebate)
Tile tray trim -Partial -Cut down by 25mm
Floor Substrate -Ceramic tiles direct fix to concrete
5.5 –Example 5
Tile tray installation -Direct to concrete (No rebate)
Tile tray trim -Full Trim
Floor Substrate -Ceramic tiles direct fix to concrete
5.6 –Example 6
Tile tray installation -Direct to concrete (No rebate)
Tile tray trim -Partial -Cut down by 25mm
Floor Substrate -Ceramic tiles direct fix to concrete
Page 09
Concrete substrate set
down by “30mm” for
Posh Tile Tray area*
Cut down 25mm
of tile tray upturn
“Water Stop”
Remaining 10mm
of tile tray upturn 9mm
Ceramic Tile: 8mm Ceramic Tile: 8mm
“Water Stop”
Aluminium T Insert” 50 x 25 x 1.6mm
- Note: Top edge cut down from 23 to 10mm
Ceramic Tile: 8mm
Ceramic Tile: 8mm
Exposed aluminium facing: 30mm
Cut down 25mm
of tile tray upturn
9mm
“Water Stop”
Remaining 10mm
of tile tray upturn
Ceramic Tile: 8mm
Ceramic Tile: 8mm
Ceramic Tile: 8mm
Posh - Solus Tile Over Shower Tray Rear Outlet of 14
6. Waterproofing
7. Tiling
Professional waterproofing contractors should be used to ensure compliance with Australian
Standard AS 3740-2010.
Note that insurers may void claims if the installation does not comply with AS3740.
All the joints between the tray and the floor/walls must be waterproofed using one of the approved waterproofing
systems as recommended - Refer Page 10.
It is also recommended that the waterproofing cover the entire surface of the tile Tray.
Do not waterproof in the area immediately around the waste outlet so as not to block water drainage
Refer AS3740.
Preliminary
Ensure tray is clean from dirt and dust, using methylated spirits will assist in removing dust.
Allow to dry before commencement of installation.
Refer Page 9 For recommended tiling adhesives and grout systems.
7.1 Rough up the surface of the Tile Tray using 80 grit sandpaper.
7.2 Apply primer over the tile tray surface and allow to dry as per primer manufacturers instructions.
7.3 Apply tile adhesive glue over the primer and bed down tiles using the required tile spacing distance as per job
requirement (i.e.: 2mm or 4mm).
7.4 Allow tile adhesive to dry from minimum 24hrs prior to grouting.
7.5 Install grouting.
7.6 Install Caulking at interface between walls and floor.
Preliminary
Ensuretrayiscleanfromdirtanddust,usingmethylatedspiritswillassistinremovingdust.
Allowtodrybeforecommencementofinstallation.
Referpage9Forrecommendedtilingadhesivesandgroutsystems
7. Tiling
7.1 Rough up the surface of the Tile Tray using 80 grit sandpaper
7.2 Apply primer over the tile tray surface and allow to dry as per primer manufacturers instructions.
7.3. Apply tile adhesive glue over the primer and bed down tiles using the required tile spacing distance as per job
requirement (i.e.: 2mm or 4mm).
7.4 Allow tile adhesive to dry from minimum 24hrs prior to grouting.
7.5. Install grouting
7.6. Install Caulking at interface between walls and floor
Page 10
Posh - Solus Tile Over Shower Tray Rear Outlet of 14
8. Adhesives & Waterproofing Products
For installation of the tray to the floor the approved adhesives are;
For waterproofing and tiling the following products are approved for use with Posh Tile Tray.
Please contact relevant suppliers to obtain detailed instructions and data sheets.
All Waterproofing systems are to be installed in accordance with best practice and the requirements of appropriate
building codes and AS3740.
Page 11
Posh - Solus Tile Over Shower Tray Rear Outlet of 14
9. Waste Outlet Connector
Waste outlet Installation - recommended method
1. Remove outer tension ring and silicone gasket from the assembly.
2. Apply a thin layer of silicone to the outlet area and place the silicone gasket onto the wet silicone.
3. Place the outlet into the tile tray outlet hole, ensuring that the sealing ring is between the outlet and the outlet hole.
4. Apply silicone to the underside of the outlet hole between the outlet and the tile tray
5. Replace the tension ring from the underside of the tile tray screwing in a clockwise direction.
6. Tighten the tension ring with a spanner, do not over tighten.
7. Attach plumbing connection to the outlet.
8. Check for water tightness, tighten further if necessary data sheets
NB : The installation of the Waste Outlet Connector is the responsibility of the installer to ensure a water tight
seal between the tray, Waste Outlet Connector and the plumbing connection. The manufacturer can only
supply recommended methods of installation.
Waste outlet Connector (Puddle Flange) For Tile Tray
Page 12
Apply a small amount of
silicone on this surface
Apply silicone in this
area to fill the gap
between the outlet and
the tile tray
Outlet
Silicone Gasket
Outer Tension
Ring
Suits Centre Rear Suits Rear Grate
Silicone Ring
Outlet
Outer Tension Ring
Posh - Solus Tile Over Shower Tray Rear Outlet of 14
10. Outlets & Grates Tile Insert Grates
Grate 840mm x 11mm
1703077 = Stainless Steel
1703078 = Matte Black
Grate 860mm x 11mm
1703081 = Stainless Steel
1703082 = Matte Black
Grate 1140mm x 11mm
1703088 = Stainless Steel
1703089 = Matte Black
Grate 1160mm x 11mm
1703092 = Stainless Steel
1703093 = Matte Black
Note:
• 840mm and 1140mm grates suit 3 wall shower.
• 860mm and 1160mm grates suit corner shower.
• 11mm depth grate suits 0 – 8mm tile thickness.
• 17.7mm depth grate suits 9mm + tile thickness.
Grate 840mm x 17.7mm
1703079 = Stainless Steel
1703080 = Matte Black
Grate 860mm x 17.7mm
1703083 = Stainless Steel
1703084 = Matte Black
Grate 1140mm x 17.7mm
1703090 = Stainless Steel
1703091 = Matte Black
Grate 1160mm x 17.7mm
1703094 = Stainless Steel
1703095 = Matte Black
Grate 100 x 100 x 12.3
1703069 = Stainless Steel
1703070 = Matte Black
Page 13
Posh - Solus Tile Over Shower Tray Rear Outlet of 14
16
6
We recommend the use of soapy water or approved cleaners. This product should not be cleaned with abrasive materials. Damage caused by
any improper treatment is not covered by the product warranty. Refer to Warranty Conditions
Plumbers, please ensure a copy of the installation
instruction is left with the end user for future reference.
Published 10/08/2023 Page 14
Replacement of Trim Set
Remove (4) and unscrew the Grub Screw (5) Decorative Cover
using Allen Key (10).
Lift off the Mixer Handle (6) remove Cartridge Dome (7) and
Cartridge Sleeve (11).
Remove mixer Backplate Set (12) .
1.
2.
3.
The Mizu Universal Inwall Body is an innovative installation
system that allows for separation of the inwall body from the
trim set kit. Once the Universal Inwall Body is installed, the
retrofittable trim set kit can be updated to another choice of
finish from the Mizu Silk range or a design and finish change
from the Mizu Drift MK2 range.
14 16
14
15
16
17
111
111
112
112
110
Number Part Quantity Chrome Matte
Black
Brushed
Nickel
Brushed
Gun
Metal
4-6
7
11
12
10
Mixer Handle Set Complete 2265003
2265020
2265024
2265016
2265002
2265019
2265023
2265015
2265001
2265018
2265022
2265014
2265000
2265017
2265021
2265013
1
Concealed Wall Mixer Cap
Concealed Wall Mixer Cartridge Sleeve
Concealed Shower Mixer Plate Set
Allen Key 2.5mm
1
1
1
1
MIZU SILK SHOWER MIXER
4-12 Mizu Silk Shower Mixer Trimset 9510749
9510748
9510747
9510746
1 Set
Remove (4) and unscrew the Grub Screw (5) Decorative Cover
using Allen Key (10).
Lift off the Mixer Handle (6) remove Cartridge Dome (7) and
Cartridge Sleeve (11).
Disassemble and remove Diverter (12-14).
Remove mixer Backplate Set (15) .
Reassemble trim set from desired range.
1.
2.
3.
4.
5
The Mizu Universal Inwall Body is an innovative installation
system that allows for separation of the inwall body from the
trim set kit. Once the Universal Inwall Body is installed, the
retrofittable trim set kit can be updated to another choice of
finish from the Mizu Silk range or a design and finish change
from the Mizu Drift MK2 range.
15
14
12
13
4
5
7
11
Number Part Quantity Chrome Matte
Black
Brushed
Nickel
Brushed
Gun
Metal
4-6
7
11
15-16
12-14
Mixer Handle Set Complete 2265003
2265020
2265024
2265028
2265002
2265019
2265023
2265027
2265001
2265018
2265022
2265026
2265000
2265017
2265021
2265025
1
Concealed Wall Mixer Cap
Concealed Wall Mixer Cartridge Sleeve
Concealed Shower Mixer Plate Set
Shower Mixer Diverter Set
1
1
1
1
MIZU SILK SHOWER DIVERTER MIXER
4-16 Mizu Silk Shower Diverter Mixer Trimset 9510753
9510752
9510751
9510750
1 Set
10 Allen Key 2.5mm 1
2265032
2265031
2265030
2265029
X
X
X
X
X
1
2
x
x
110
10. Outlets & Grates (Cont’d) Punched Grates
Note:
• 840mm and 1140mm grates suit 3 wall shower.
• 860mm and 1160mm grates suit corner shower.
1703075
Punched Grate
840mm x 12.7mm
Stainless Steel
1703076
Punched Grate
860mm x 12.7mm
Stainless Steel
1703086
Punched Grate
1140mm x 12.7mm
Stainless Steel
1703087
Punched Grate
1160mm x 12.7mm
Stainless Steel
1703071
Round Grate
50mm
Stainless Steel
1703072
Square Grate
50mm
Stainless Steel
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14

Posh 9512231 Installation guide

Posh
Brand
Posh
Model
9512231
Type
Installation guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents