Kado 9503987 Installation guide

Category
Sanitary ware
Type
Installation guide

Kado 9503987 is a close coupled back to wall overheight back inlet toilet suite in white with a 4-star WELS rating. It features a dual flush system with a full flush of 80 and a half flush of 40. The toilet suite has a height of 800mm, a width of 390mm, and a depth of 600mm. The water inlet is located at the rear of the toilet suite and requires a 15mm mini cistern stop. The waste outlet can be set out to a minimum of 95mm and a maximum of 180mm. The toilet suite comes with a top-fix plastic fixing nut and bolt, as well as screws and caps for fixing to the floor. It also includes a pan connector, rod, and bracket for connecting to the waste bend.

Kado 9503987 is a close coupled back to wall overheight back inlet toilet suite in white with a 4-star WELS rating. It features a dual flush system with a full flush of 80 and a half flush of 40. The toilet suite has a height of 800mm, a width of 390mm, and a depth of 600mm. The water inlet is located at the rear of the toilet suite and requires a 15mm mini cistern stop. The waste outlet can be set out to a minimum of 95mm and a maximum of 180mm. The toilet suite comes with a top-fix plastic fixing nut and bolt, as well as screws and caps for fixing to the floor. It also includes a pan connector, rod, and bracket for connecting to the waste bend.

Installation Instructions
Kado Lux Close Coupled Back to Wall Overheight
Back Inlet Toilet Suite White (4 Star)
Plumbers, please ensure a copy of the installation
instructions is left with the end user for future reference.
Set-Up
1. Rough in positions of water inlet, waste outlet and fixing bracket holes. Ensure inlet connection extends 40mm
from finished wall. Prepare waste outlet according to required setout (95mm min - 180mm max) and drill floor
fixing brackets into position (60mm inside traced mark of pan rim).
2. Insert top-fix plastic fixing nut and bolt into pan (supplied).
S-Trap Installation
1. Lubricate the rubber fins of the pan bend and position in the waste pipe at the required height. Fix the pan
connector back to the wall using the rod and bracket.
2. Align and push pan back to wall, connect pan spigot into waste bend ensuring firm connection.
3. Fix cistern onto pan, bucket flush and check for leaks.
Water Inlet & Levelling Pan
1. Connect rear water inlet valve using 15mm mini cistern stop supplied. Fill the cistern and ensure correct water
level. For adjustment refer separate inlet valve instructions.
2. Ensure that pan is level and that cisterns align with wall. Make minor adjustments if necessary.
3. Fix pan to floor using screws and caps provided.
4. Silicone pan to floor. Remove excess sealant.
180
WALL WALL WALL
FINISHED FLOOR LEVEL FINISHED FLOOR LEVEL
95-180mm
215
60
180
95-180
80
800
Water Inlet
390
80
70
60
285
360
Front View
Water
Inlet
Height
250
800
Published 23/11/2020
page 1 of 2
Dimensions are nominal measurements only.
SEALANT
15mm Mini Ball Valve
Flexible Hose
NOTE: Ensure back inlet connection
extends 40mm from finished wall
Back Inlet
Connection
Finished
Wall
40mm
Plumbers, please ensure a copy of the installation
instructions is left with the end user for future reference.
Published 23/11/2020
PUSH BUTTON ASSEMBLY AND ADJUSTMENT
1
2
Loosen lock nut
Tighten lock nut
Adjustment
Lock out
Full flush
Half flush
Ensure button rods are aligned with full & 1/2 flush on outlet valve.
Installation Instructions
Kado Lux Close Coupled Back to Wall Overheight
Back Inlet Toilet Suite White (4 Star)
page 2 of 2
Dimensions are nominal measurements only.
  • Page 1 1
  • Page 2 2

Kado 9503987 Installation guide

Category
Sanitary ware
Type
Installation guide

Kado 9503987 is a close coupled back to wall overheight back inlet toilet suite in white with a 4-star WELS rating. It features a dual flush system with a full flush of 80 and a half flush of 40. The toilet suite has a height of 800mm, a width of 390mm, and a depth of 600mm. The water inlet is located at the rear of the toilet suite and requires a 15mm mini cistern stop. The waste outlet can be set out to a minimum of 95mm and a maximum of 180mm. The toilet suite comes with a top-fix plastic fixing nut and bolt, as well as screws and caps for fixing to the floor. It also includes a pan connector, rod, and bracket for connecting to the waste bend.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI