Mircom LT-2085 TX3-CX-1 Quick Start

Brand: Mircom

Model: LT-2085 TX3-CX-1

Type: Quick Start

Mircom LT-2085 TX3-CX-1 is a versatile access control device that offers a range of features for securing and managing access to your premises. With its built-in card reader, you can grant or deny access based on authorized credentials, enhancing the security of your property. The device's programmable outputs allow you to connect and control various devices such as door locks, gates, or lights, providing you with flexible access control options.

TX3-CX-1 QUICK START

WARNING: Disconnect the power before wiring.

RS-485 wiring maximum length: 1219.2 m (4000 ft)

PoE maximum length: 100 m (328 ft)

Wiegand connection maximum length: 152.4 m (500 ft)

TX3-CX-1 dimensions:

122 mm x 79 mm x 41 mm

(4 25/32” x 3 3/32” x 1 39/64”)

Contents of Kit:

TX3-CX-1

Mounting plate

Screwdriver for terminal block

2 screws for mounting plate

1 screw for securing body to mounting plate

USB ash containing manuals and software

USB cable for conguration

Subject to change without prior notice

See http://www.mircom.com/tx3 for the latest information

For more information, see LT-6618 on the USB ash.

Mircom Tech Support: 1-888-MIRCOM5 (888-647-2665) [email protected]

LT-2085 rev 3 © Mircom 2018. Printed in Canada

Shielded or unshielded Cat 5 cable

RS-485

Optional common reference

connection if available

120Ω

First controller on

network

Last controller on

network

Connect shield to one controller’s

chassis ground, which should

then connect to building ground

Use DIP switches 1-6 to set the RS-485 network address.

Leave DIP switch 7 o.

Set DIP switch 8 o to get an IP address from the DCHP server.

Set DIP switch 8 on to set a xed IP address using the TX3

Congurator software.

Switches are numbered 1-8 from left to right.

DIP Switches

MOUNTING

Single gang box

Wall Mounting plate

Screws

Side view

Press until it clicks.

Secure with the

provided screw.

WIEGAND CONNECTIONS

22-16 AWG

DATA 0

GND

DATA 1

BEEP

LED (G)

PWR

INPUT 4

General purpose

22 AWG

INPUT 3

General purpose

22 AWG

INPUT 2

Request to Exit (built-in reader)

22 AWG

INPUT 1

Door contact (built-in reader)

22 AWG

LED (R)

RJ45 connector for Internet

communication. Power can be provided

through Power over Ethernet if not

provided by the DC power terminals.

Micro USB port:

Connect to computer for network

rmware upgrade and

conguration

(maximum length of USB cable:

8 feet/2.4 m)

12 VDC / 15 W

Input power

18 AWG

24-48 VDC / 15 W

Input power (20-18 AWG)

OUTPUT 1

Door Lock

18 AWG

OUTPUT 2

General purpose

18 AWG

OUTPUT 3

12 VDC/500 mA max.

solid state output for a

DC lock

22-18 AWG

DIP switches for setting RS-485 address

RS-485

Set ON if unit is used as rst or last controller on

RS-485 network, and an external resistor is not

used. Otherwise set OFF.

Outputs 1 and 2 are relay contact

programmable outputs with the

following characteristics:

normally open (NO)

normally closed (NC) available

30 VDC/1 A, 0.6 power factor

125 VAC/0.25 A, 0.6 power factor

Recommended distance and gauge for TX3 card readers:

Use 20 AWG for 152.4 m (500 ft)

Use 22 AWG for 76.2 m (250 ft)

For other card readers, consult your reader installation

manual for recommended distances and gauges.

Note: TX3-CX-1 has a tamper feature. If it is powered on and not

mounted on the mounting plate, a tone sounds. The tone stops

sounding when it is mounted.

Mircom LT-2085 TX3-CX-1 Quick Start

Mircom LT-2085 TX3-CX-1 Quick Start

Mircom LT-2085 TX3-CX-1 Quick Start

Related papers

Other documents