Johnson Controls Metasys Integrator MS-MIG3520-0 Installation Instructions Manual

Brand: Johnson Controls

Model: Metasys Integrator MS-MIG3520-0

Type: Installation Instructions Manual

This manual is also suitable for

Metasys Integrator® MIG3500 Series Installation Instructions 1

Applications

The Metasys Integrator® MIG3500 Series unit is an

interface device that connects third-party devices to a

Metasys® Building Automation System (BAS). The

MIG3500 uses the same hardware platform as the

Network Automation Engine (NAE) 45, but contains the

firmware of the MIG300 Series Metasys Integrator unit.

See Figure 1.

North American Emissions Compliance

United States

Canada

This equipment has been tested and found to comply with

the limits for a Class A digital device pursuant to Part 15 of

the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference when

this equipment is operated in a commercial environment.

This equipment generates, uses, and can radiate radio

frequency energy and, if not installed and used in

accordance with the instruction manual, may cause

harmful interference to radio communications. Operation

of this equipment in a residential area is likely to cause

harmful interference, in which case the user will be

required to correct the interference at his/her own

expense.

This Class (A) digital apparatus meets all the requirements

of the Canadian Interference-Causing Equipment

Regulations.

Cet appareil numérique de la Classe (A) respecte toutes

les exigences du Règlement sur le matériel brouilleur du

Canada.

Figure 1: Front of MIG3500 Showing Dimensions, mm (in.), and Physical Features

2.5

FIG:MIGfrnt_dim

24 VAC

Power Terminal

RJ-45 8-Pin

Ethernet

Port

Config Port - RS-232C

Port

(Commissioning)

End-of-Line

Switch

Vendor A

RS485

Port

Battery

Compartment

System Status

Light-Emitting Diodes

(LEDs)

FIG:MIGfrnt

Restart Switch

Access Hole

Vendor B

RS232C

Port

N2 Bus

RS485

Port

RS485B

End-of-Line

Switch

131

5.2

270

10.6

Metasys Integrator® MIG3500 Series

Installation Instructions

MS-MIG3520-0

Part No. 24-10050-30, Rev. A

Release 10.0

Issued January

27, 2009

Supersedes October 6, 2008

Metasys Integrator® MIG3500 Series Installation Instructions2

Installation

Follow these guidelines when installing an MIG3500:

• Transport the MIG3500 in the original container to

minimize vibration and shock damage to the

MIG3500.

• Verify that all the parts shipped with the MIG3500.

• Do not drop the MIG3500 or subject it to physical

shock.

• Do not open the MIG3500 housing (except the

battery compartment). The MIG3500 has no

user-serviceable parts inside.

Parts Included

• one MIG3500 with removable terminal plugs

• one Lithium non-rechargeable battery (installed

and connected at the factory)

• one Installation Instructions sheet

Materials and Special Tools Needed

• three fasteners appropriate for the mounting

surface (#8 screws or M4 screws) or one 8 in.

(or longer) piece of DIN rail and appropriate

hardware for mounting the DIN rail

• small straight blade screwdriver for securing wires

in the terminal blocks

Mounting

Location Considerations

Follow these guidelines when mounting an MIG3500:

• If the MIG3500 is to replace an existing MIG300,

see Legacy MIG300 Replacement Considerations

• Ensure that the mounting surface can support the

MIG3500 and any user-supplied enclosure.

• Mount the MIG3500 in proper orientation

(Figure 2). A horizontal mounting orientation is

preferred, but the unit can also be mounted

vertically.

• Mount the MIG3500 on an even surface in wall

mount applications whenever possible. If you must

mount the MIG3500 on an uneven surface, be

careful not to crack the mounting clips or MIG3500

housing when tightening the screws. Use shims or

washers to mount the MIG3500 evenly on the

mounting surface.

• Mount the MIG3500 in areas free of corrosive

vapors, and observe the environmental limitations

listed in the Technical Specifications

section.

• Allow sufficient space for cable and wire

connections (Figure 1).

• Do not mount the MIG3500 where the ambient

temperature may exceed 50°C (122°F).

• Do not mount the MIG3500 on surfaces that are

prone to vibration or in areas where

electromagnetic emissions can interfere with

MIG3500 communication.

• Do not obstruct the MIG3500 housing ventilation

holes.

• Do not mount the power transformer below the

MIG3500.

For applications where the MIG3500 is mounted inside

a panel or enclosure, follow these additional guidelines:

• Do not install the MIG3500 in an airtight enclosure.

• Do not install heat-generating devices in the

enclosure with the MIG3500 that may cause the

ambient temperature to exceed 50°C (122°F).

Mounting the MIG3500

Wall Mount Applications

Use the holes in the three mounting clips for wall mount

applications. To mount the MIG3500 on a wall (or other

vertical surface):

1. Ensure that all three mounting clips are inserted

into the back of the MIG3500 housing. Pull the

bottom two clips outward and snap them firmly into

the extended position (Figure 3).

2. Mark the location of the three wall mount holes

using the dimensions in Figure 2, or hold the

MIG3500 up to the wall as a template and mark the

locations.

3. Drill holes in the wall at the locations marked in

Step 2 and insert wall anchors (if necessary).

4. Position the MIG3500 and insert the screws

through the holes in the mounting clips, and

carefully tighten all the screws.

DIN Rail Mount Applications

To mount the MIG3500 on a DIN rail:

1. Securely mount and center an 8 in. (or longer)

section of DIN rail in the required space.

IMPORTANT: Do not overtighten the mounting

screws. Overtightening the screws may damage the

mounting clips or MIG3500 housing.

Metasys Integrator® MIG3500 Series Installation Instructions 3

2. Ensure that the bottom two mounting clips are

pulled outward and snapped firmly into the

extended position (Figure 3).

3. Hang the MIG3500 by the DIN rail hooks (Figure 3)

on the top track of the DIN rail, and position the

MIG3500 DIN rail channel snugly against the

tracks of the DIN rail.

4. Push the bottom mounting clips up to secure the

MIG3500 on the DIN rail tracks.

To remove the MIG3500 from the DIN rail, snap the

bottom DIN clips to the outward extended position, and

carefully lift the MIG3500 off the DIN rail.

Enclosure Mount Applications

Mount the enclosure per the manufacturer’s

instructions and mount the MIG3500 in the enclosure

following the guidelines in the Location Considerations

and Mounting the MIG3500

sections.

Legacy MIG300 Replacement Considerations

Follow these important guidelines if the MIG3500

replaces an existing MIG300 controller:

• The unit size of the MIG3500 is slightly longer than

the MIG300; however, the MIG3500, like the

MIG300, is designed for DIN-rail mounting on the

horizontal plane (Figure 4). You can also mount it

with screws, either horizontally or vertically. See

Mounting the MIG3500

for details.

• The wire termination locations on the MIG3500 are

different from the MIG300 (Figure 1). Pay close

attention to this when routing wires to their new

locations on the MIG3500.

• Similar to the MIG300, the MIG3500 also requires

24 VAC power. See the Wiring

section.

• The N2 Bus termination on the MIG300 is labeled

N2 Port, whereas the N2 Bus termination on the

MIG3500 is called N2 - RS485. If using N2 Bus

wiring that includes a shield, refer to the

N2 Communications Bus Technical Bulletin

(LIT-636018) for additional information on

terminating a shield.

• For the MIG3500, an Ethernet port is available and

is used only for downloading firmware. For details,

refer to the Metasys Integrator 3500 Series

Commissioning Guide (LIT-12011439).

Figure 2: MIG3500 Mounting Screw Hole

Dimensions and Mounting Area Requirements,

mm (in.)

FIG:MIGmnthol

121

4.8

Mounting

Holes

2.6

140

5.5

2.2

130

5.1

210

8.3

350

13.8

Mounting

Holes

Figure 3: DIN Rail and Mounting Clip Features

on the Back of an MIG3500

FIG:MIG_bck

DIN Rail

Channel

Mounting Clips

(in Extended Positions)

DIN Rail

Hooks

DIN Rail

Hooks

Figure 4: Recommended Installation Location of

MIG3500 and Transformer in Standard Enclosure

FIG:MIGewc_cmp

Metasys Integrator® MIG3500 Series Installation Instructions4

• The serial ports on the MIG3500 are not labeled

the same as the serial ports on the MIG300. See

Table 1.

• As indicated in Table 1, Port 1 on the older models

is equivalent to the Config Port - RS232C

commissioning port on the MIG3500. When you

commission the device, connect the serial cable

from the computer to the Config Port - RS232C

port on the MIG3500.

• Also indicated in Table 1, Port 2 on the older

models has no equivalent port on the MIG3500. A

device using RS-485 communication can be

connected directly to the Vendor A - RS485 port

on the MIG3500. If the device uses RS-232

communication, an RS-232 to RS-485 converter is

needed before you can use this port; or, you can

use the Vendor B - RS2323C port instead.

• And lastly in Table 1, Port 3 on the older models is

equivalent to the Vendor B - RS232C port on the

MIG3500. A device connected to Port 3 on the

MIG300 can be switched to the Vendor B -

RS232C port on the MIG3500.

• While the MIG3500 is restarting, the LEDs on the

unit indicate its status.

Wiring

Power Supply, Network, and Communication

Connections

See Figure 1 for the location of the power supply

terminal, RS-232 and RS-485 terminals, and Ethernet

port on the MIG3500. For additional information

regarding these connections, refer to the Metasys

Integrator 3500 Series Commissioning Guide

(LIT-12011439).

Power Supply

In North America, the MIG3500 requires a dedicated

Class 2, 24 VAC, 25 VA minimum power supply.

Outside North America, use a 24 VAC Safety

Extra-Low Voltage (SELV) transformer at the

appropriate rating. The minimum input voltage for the

MIG3500 to operate properly is 20 VAC. Maximum

power consumption is 25 VA.

Config Port - RS232C Port

The Config Port - RS232C serial port (Figure 1) is for

a direct connection using a standard 9-pin female to

9-pin female Data Terminal Equipment (DTE) to

DTE null modem cable. Use this port exclusively as a

commissioning port. It provides a VT100 terminal

emulation interface to the unit.

Vendor A - RS485 Network Terminal

The Vendor A - RS485 network terminal is a 4-position

removable, keyed terminal block. Use this terminal for

a vendor device that requires an RS-485 interface.

Vendor B - RS232C Port

The Vendor B - RS232C serial port (Figure 1) is for a

direct DTE connection. Connect to DTE equipment with

a null modem cable or to Data Circuit Equipment (DCE)

with a straight-through cable. Use this port to connect

third-party equipment that requires an RS-232

interface.

N2 - RS485 Bus Terminal

The N2 - RS485 bus network terminal is a 4-position

removable, keyed terminal block. Use this terminal to

connect to MIG3500 to the Metasys N2 network.

Refer to the N2 Communications Bus Technical

Bulletin (LIT-636018) for information and guidelines on

wiring devices on the N2 Bus.

Ethernet Port

The Ethernet connection (10 or 100 Mb/s) is an 8-pin

RJ-45 network port (Figure 1). Use this port only if you

need to load the firmware with the Metasys MIG

Update Utility (MUU) over an Internet Protocol (IP)

network connection. Do not connect the MIG3500 to a

local area network. For information on the MUU, refer

to the Metasys Integrator 3500 Series Commissioning

Guide (LIT-12011439).

Table 1: Port Comparisons: MIG300 to MIG3500

MIG300 MIG3500 Usage

Commissioning

Port

Config -

RS232C

Configuration/

Commissioning

Vendor Port A

1. On the MIG300, this is an RS232C port. On the

MIG3500, this is a native RS485 port.

Vendor A -

RS485

Vendor device

communication

Vendor Port B Vendor B -

RS232C

Vendor device

communication

N2 N2 - RS485 N2 Bus communication

Metasys Integrator® MIG3500 Series Installation Instructions 5

Wiring the MIG3500

Mount the MIG3500 securely before wiring the unit.

See the Mounting

section.

Follow these guidelines when wiring an MIG3500:

• Route the supply power wires and communication

cables at least 50 mm (2 in.) away from the vent

slots on the sides of the MIG3500 housing.

• Provide slack in the wires and cables. Keep cables

routed neatly around the MIG3500 to promote

good ventilation, Light-Emitting Diode (LED)

visibility, and ease of service.

To wire the MIG3500:

1. Connect the three N2 Bus wires to the removable

4-terminal plug as shown in Figure 5 and plug into

the port labeled N2 - RS485. If a shield is present,

follow standard practices for terminating a shield

as discussed in the N2 Bus literature. Refer to the

N2 Communications Bus Technical Bulletin

(LIT-636018).

2. If you have a vendor device with an RS-232

interface, connect the appropriate computer cable

to the Vendor B - RS232C port as shown in

Figure 6.

IMPORTANT: Do not connect 24 VAC supply

power to the MIG3500 before finishing wiring and

checking all wiring connections. Short circuits or

improperly connected wires may result in permanent

damage to the equipment.

IMPORTANT: Use copper conductors only. Make

all wiring in accordance with local, national, and

regional regulations. The MIG3500 is a low-voltage

(<30 VAC) device. Do not exceed the MIG3500

electrical ratings.

IMPORTANT: Do not remove the terminal block

keys. The terminal block plugs and the terminal

sockets are keyed to fit together in the correct

configuration only.

IMPORTANT: Prevent any static electric discharge

to the MIG3500. Static electric discharge can

damage the MIG3500 and void any warranties.

IMPORTANT: Make sure the building automation

network wiring meets the specifications, rules, and

guidelines in the Power Supply, Network, and

Communication Connections section in this

document.

Figure 5: N2 Bus Wiring

N2 - RS485

(N2 Bus)

Terminal

Block

N2 - RS485

(N2 Bus)

Terminal Block

Plug

FIG:MIGN2_bs

SHLD

COM

N2+N2-REF

Figure 6: RS-232 Vendor Wiring

From Vendor Device

(RS232)

FIG:RS232-conn

Vendor B - RS232C Port

Metasys Integrator® MIG3500 Series Installation Instructions6

3. If you have a vendor device with an RS-485

interface, connect its communication wires to the

Vendor A - RS485 terminal block plug as shown in

Figure 7.

4. If you have a second vendor device with an

RS-232 or RS-485 interface, connect an RS-232 to

RS-485 converter between the appropriate vendor

port on the MIG3500 and the vendor device,

referring to Figure 6 (RS-232) or Figure 7

(RS-485). This connection may also require a

gender changer or 9-to-25 pin adapter.

5. Connect the 24 VAC supply power wires from the

transformer to the removable 3-terminal plug as

shown in Figure 8. The middle terminal is not used.

Note: Power supply wire colors may be different on

transformers not manufactured by Johnson Controls.

Follow the transformer manufacturer’s instructions or

the project installation drawings.

Note: When connecting 24 VAC power to the

MIG3500s and field devices on the network, be

consistent so that transformer phasing is uniform

across the devices. Powering devices with uniform 24

VAC supply power phasing reduces noise,

interference, and ground loop problems. The MIG3500

does not require an earth ground connection.

Wiring Considerations and Guidelines for Network Integrations

Figure 7: RS-485 Vendor Wiring

Vendor A

RS485

Terminal Block

Plug

FIG:vndrA

REF

From Vendor Device (RS-485)

Figure 8: 24 VAC Supply Power Wiring

Power Terminal

Block

Power Terminal

Block Plug

Wires from

Johnson Controls

24 VAC Class 2

Power Transformer

Brown Wire

(COM)

Orange Wire

(24 VAC)

FIG:MIGpwr_prt

24V~

COM

HOT

Table 2: Guidelines for Vendor Networking

Category Rules/Maximums Allowed

General The MIG3500 can have either:

• One RS-485 device interface and one RS-232 device interface

• Two RS-485 device interfaces

• Two RS-232 device interfaces

1. One of the device interfaces requires RS232 to RS485 converter as an additional component.

Only daisy

-chained devices

Number of Supported Devices Refer to the vendor-specific application note available on QuickLit.

RS-232 Cable Length Up to 19,200 baud: 15 m (50 ft) between MIG3500 and vendor equipment

Higher than 19,200 baud: 4 m (13 ft) between MIG3500 and vendor equipment

RS-485 Cable Length and Type 1,500 m (5,000 ft) twisted pair cable without a repeater

4,500 m (15,000 ft) twisted pair cable from an NAE and the farthest FC device (three

segments of 1,500 m [5,000 ft] each, separated by repeaters)

2,000 m (6,600 ft) between two fiber modems

RS-485 Cable Wire Type and Size Solid or stranded 22 AWG recommended (24 AWG twisted pair or larger is acceptable)

Terminations EOL switch available for RS-485 B terminal port (if required)

Metasys Integrator® MIG3500 Series Installation Instructions 7

Setup and Adjustments

Battery

The MIG3500 is shipped with a battery installed and

connected. If the MIG3500 experiences a power loss,

the battery maintains the current time and date stored

in the unit. The battery is non-rechargeable and field

replaceable.

Turning On the MIG3500

After applying 24 VAC power, the MIG3500 requires

approximately 2 minutes to start up and become

operational. See the LED Test Sequence at Startup

section.

Startup is complete and the MIG3500 is operational

when the (green) RUN LED is On steady and the (red)

FAULT LED is Off (Figure 11). If this is a new MIG3500

without a firmware image, the RUN LED continues to

flash, indicating that the unit needs to be

commissioned with the MUU. Refer to the Metasys

Integrator 3500 Series Commissioning Guide

(LIT-12011439) for additional information on

commissioning an MIG3500.

Disconnecting Power from the MIG3500

When 24 VAC supply power to a MIG3500 is

disconnected or lost, the MIG3500 turns off

immediately.

Setting N2 Bus End-of-Line Switch

N2 Bus applications require at least one terminated

device on each N2 Bus segment; but two terminated

devices, one at each end of the N2 Bus segment, are

recommended. The MIG3500 has an End-of-Line

(EOL) switch that allows you to set the MIG3500 as a

terminated device. The MIG3500 is shipped with the

EOL A switch in the factory default, ON (up) position

(Figure 9). Set the EOL A switch to the appropriate

position for each MIG3500 in your network. For more

details, refer to the Setting Terminations section of the

N2 Communications Bus Technical Bulletin

(LIT-636018).

Setting RS485 EOL B Switch

RS485 serial protocol bus segments require proper

EOL termination to reduce interference from signal

bounce back on the bus segment. An EOL switch for

the Vendor A - RS485 port on the MIG3500 is provided

for this purpose. Vendor devices at either end of the

RS485 bus must be set as terminated devices. The

MIG3500 is shipped with the EOL B switch in the

factory default, ON (up) position (Figure 10). Set the

EOL B switch to the appropriate position for each

MIG3500 in your network.

Troubleshooting

LED Status Indicators

The MIG3500 has a bank of LEDs to indicate power

and network communication status. Figure 11 shows

the LEDs and Table 3 describes the LED indications.

IMPORTANT: Wait for the MIG3500 to complete

the start-up sequence and the RUN LED to go On

steady before initiating any other action on the

MIG3500.

Figure 9: N2 Bus EOL A Switch in the

Factory Default ON (Up) Position

FIG:MIG_EOL

Figure 10: RS485 EOL B Switch in the Factory

Default ON (Up) Position

FIG:MIG_EOL

Figure 11: MIG3500 LED Designations

ETHERNET

10 LINK

100 LINK

RUN

POWER

FAULT

N2 PORT TX

VENDOR A TX

VENDOR B TX

VENDOR B RX

FIG:MIG_LED

Metasys Integrator® MIG3500 Series Installation Instructions8

LED Test Sequence at Startup

When you connect power to the MIG3500, it initiates a

2-second LED test to verify the operational status of its

LEDs. After this test, the operating system is loaded,

the MIG3500 application starts, the MIG3500 database

is loaded from flash memory, and MIG3500

initialization occurs.

A steady On RUN LED indicates a fully initialized

MIG3500. For details, refer to the Metasys Integrator

3500 Series Commissioning Guide (LIT-12011439).

For more information about the other possible

behaviors of the MIG3500 LEDs, see Table 3.

Repair Information

If you replace an MIG3500 on a site with a new

MIG3500 for any reason, or add a new MIG3500 to a

site, you must update the system database to ensure

that the new MIG3500 is recognized and able to

communicate with the site.

Refer to the Metasys Integrator 3500 Series

Commissioning Guide (LIT-12011439) for information

on removing an MIG3500 from service and configuring

a replacement MIG3500.

Table 3: MIG3500 LED Designations, Normal Status, and Descriptions

LED Designation Normal Status Descriptions/Other Conditions

POWER (Green) On Steady On Steady = Unit is getting power from the 24 VAC supply.

Off Steady = Unit is shut down.

FAULT (Red) Off Steady Flicker Once, Then Device Continually Restarts = Internal fault has

occurred.

N2 PORT TX

(Green)

Flicker Flicker = Normal communications; the N2 Bus is transmitting and receiving

data. Flickers are generally in sync with data transmission, but should not be

used to indicate specific transmission times.

Off Steady = No field controllers are defined for the MIG3500 N2 Bus.

VENDOR A TX

(Green)

Flicker Flicker = Data is being transmitted from the MIG3500 to the vendor device

connected to the Vendor A - RS485 port.

VENDOR B TX

(Green)

Flicker Flicker = Data is being transmitted from the MIG3500 to the vendor device

connected to the Vendor B - RS232C port.

VENDOR B RX

(Green)

Flicker Flicker = Data is being received by the MIG3500 from the vendor device

connected to the Vendor B - RS232C port.

ETHERNET (Green) Flicker Flicker = Data is transferring on the Ethernet connection. This LED is only

active when the MUU is downloading the firmware to the unit.

Off Steady = No Ethernet traffic on the Ethernet connection, indicating the

MUU is not in use or is not downloading the firmware to the unit.

10/LINK (Green) On Steady On Steady = Ethernet connection is established at 10 Mbps.

100/LINK (Green) On Steady On Steady = Ethernet connection is established at 100 Mbps.

RUN (Green) On Steady On Steady = MIG3500 software is fully initialized.

Off = MIG3500 unit is not powered or is starting up.

On 0.5 seconds, Off 0.5 seconds = MIG3500 software is starting up.

Table 4: MIG3500 Ordering Information

Product Code

Number

Description

MS-MIG3520-0

MIG3500 Metasys Integrator: Requires a 24 VAC power supply. Each model includes one RS-232-C

commissioning port, one_RS-232-C vendor serial port, one RS-485 vendor port, one N2 Bus

communication port, one Ethernet port, and a battery.

MS-MIGSWO-1 Metasys Integrator software with latest version of all downloadable drivers/tables used to

commission MIG3500.

1. For the European version, add an E after the code number. For repair parts, replace the -0 suffix with -700.

Metasys Integrator® MIG3500 Series Installation Instructions 9

Technical Specifications

Table 5: MIG3500 Accessories Ordering Information

Product Code

Number

Description

Y65T31-0 Power transformer (Class 2, 24 VAC, 40 VA maximum output), no enclosure

AS-XFR050-0

Power transformer (Class 2, 24 VAC, 50 VA maximum output), no enclosure

EN-EWC25-0 Standard enclosure with dimensions: 406 x 406 x 190 mm (16 x 16 x 7.5 in.)

MM-CVT101-0 RS232 to RS485 Converter (old style)

AS-CVTPRO300-1 Zone Bus/N2 Bus Interface Converter with 120 VAC/3 VDC External Power Adapter (North American

version)

IU-9100-8401 RS232 to RS485 Interface Unit (European use only)

MIG3500 Model

Power Requirement Dedicated nominal 24 VAC, Class 2 power supply (North America), Safety Extra-Low

Voltage (SELV) power supply (Europe), at 50/60 Hz (20 VAC minimum to 30 VAC

maximum)

Power Consumption 25 VA maximum

Ambient Operating Temperature 0 to 50°C (32 to 122°F)

Ambient Operating Conditions 10 to 90% RH, 30°C (86°F) maximum dew point

Ambient Storage Temperature -40 to 70°C (-40 to 158°F)

Ambient Storage Conditions 5 to 95% RH, 30°C (86°F) maximum dew point

Battery Non-rechargeable lithium 3.0 V, 160 mAh; typical life of 5 to 7 years at 21°C (70°F)

Panasonic® CR2025 or equivalent

Processor 192 MHz Renesas™ SH4 7760 RISC processor

Memory 128 MB Flash nonvolatile memory

128 MB Synchronous Dynamic Random Access Memory (SDRAM)

Operating System Microsoft® Windows® CE embedded

Network and Serial Interfaces One Ethernet port; 10/100 Mb/s; 8-pin RJ-45 connector

One optically isolated RS-485 port; 9600 bps; pluggable and keyed 4-position terminal

block

Two RS232C serial ports with standard 9-pin sub-D connectors that support standard

baud rates.

Dimensions

(Height x Width x Depth)

131 x 270 x 62 mm (5.2 x 10.6 x 2.5 in.)

Minimum space for mounting: 210 x 350 x 110 mm (8.3 x 13.8 x 4.3 in.)

Housing Plastic housing material: ABS + polycarbonate; Protection: IP20 (IEC60529)

Mounting On flat surface with screws on three mounting clips or a single 35 mm DIN rail

Shipping Weight 1.2 kg (2.7 lb)

Compliance United States

UL Listed (PAZX), UL 916

FCC compliant, CFR47, Part 15, Class B

Canada

UL Listed (PAZX7), CAN/CSA C22.2 No. 205

Industry Canada compliant

Europe

EMC Directive, 89/336/EEC

Australia/New Zealand

C-Tick mark compliant

The performance specifications are nominal and conform to acceptable industry standard. For application at conditions beyond these

specifications, consult the local Johnson Controls® office. Johnson Controls, Inc. shall not be liable for damages resulting from misapplication

or misuse of its products.

Published in U.S.A. www.johnsoncontrols.com

Metasys Integrator® MIG3500 Series Installation Instructions10

Metasys® and Johnson Controls® are registered trademarks of Johnson Controls, Inc.

Building Efficiency

507 E. Michigan Street, Milwaukee, WI 53202

Johnson Controls Metasys Integrator MS-MIG3520-0 Installation Instructions Manual

Brand: Johnson Controls

Model: Metasys Integrator MS-MIG3520-0

Type: Installation Instructions Manual

This manual is also suitable for

Download PDF

report

Johnson Controls Metasys Integrator MS-MIG3520-0 Installation Instructions Manual

This manual is also suitable for

Johnson Controls Metasys Integrator MS-MIG3520-0 Installation Instructions Manual

Related papers

Other documents