i3 International Do721 Quick start guide

i3 International
Brand
i3 International
Model
Do721
Category
Security cameras
Type
Quick start guide
QUICK START GUIDE
Do721-series Outdoor Vandal Camera
SAFETY
1. This quick start guide is designed for users who have an adequate
knowledge of CCTV cameras.
2. For maximum optical clarity, the camera or lens must remain clean.
Use a soft, dry cloth to remove finger prints and dust from the
dome cover
3. Ensure the supplied voltage meets the power consumption
requirements of this camera before powering the camera on.
4. To avoid electrical shock and to preserve the product warranty,
DO NOT disassembles the camera. Refer servicing to qualified
personnel only.
5. For more details on installation and operation, please refer to the
CD provided.
PACKAGE CONTENTS
• Flat Head Screw (Tapping Type) x4
• Plastic Anchor x4
• Security Tort wrench x1
• O-rings x4
• 2nd video monitor output cable x1
• Rubber gasket x1
• Guide Pattern sticker x1
• Flush Mount template (the box lining) x1
• Fully Assembled Camera x1
MOUNTING THE CAMERA (SURFACE MOUNT)
1. Attach the Guide Pattern Sticker to the wall or ceiling.
2. Drill two holes on the mounting surface and insert the plastic anchors (#1) into the
holes.
3. Complete drilling 2 holes on the base of the camera to match the 2 holes drilled
on the mounting surface.
(Recommendation: Surface conduit should point down to create a drip-loop.)
4. Remove the protective film from the black rubber gasket and adhere to the base
of the outdoor model cameras.
5. Secure the bottom case to the wall or ceiling with the Flat Head Screws (tapping
type) (#2).
For your convenience, the holes on the outdoor housing are started but not drilled
all the way through for moisture control.
Note: Depending on the material of your mounting surface, you may require different
screws and anchors than those supplied.
INSTALLATION
The dome camera is a fully integrated enclosure with camera and lens.
1. Bottom case
2. Camera base
3. Tilt adjustment
bracket
4. Inner liner
(Not present on
Do721R model
series)
5. Dome cover
6. Anti drop hook
1. Plastic Anchors
2. Flat Hand Screws
(Tapping Type)
Note: outdoor
screws come with
O-rings included.
Note: The Do-series
cameras come with
a large rubber gasket
to provide the seal
between the mounting
surface and the camera
base.
Figure 2. Disassembling the camera
Figure 3. Camera Surface Mounting
Applicable to the following models:
Do721, Do721R, Do721P, Do721RP
a
b
8
1. Conduit holes used for surface run power/video
connector
a. Side conduit hole (1/2”).
When using outdoors, sealant must be
used to maintain the IP67 status.
b. Top conduit hole (3/4”) (can also be used
for pendant mount).
When using outdoors, sealant must be
used to maintain the IP67 status.
2. Bottom case
3. Camera Base
4. Dome cover
5. Focus lever
6. Zoom lever
7. Video output connector
8. 24 VAC / 12 VDC power input connector (red
+, black -)
Figure 1. Camera Parts
i3-TRNG-CAMS-Do721-series-QuickGuide.indd
Rev. 130130
QUICK START GUIDE
Do721-series Outdoor Vandal Camera
ADJUST THE CAMERA POSITION
The dome camera has three axis for positioning the camera. While live viewing
on the monitor, adjust the camera position as follows:
• Horizontal adjustment rotates 3D assembly in the base.
• Vertical adjustment: After loosening the screw on the bracket, position the
camera as desired, and tighten the screw back to the bracket.
• Horizontal rotation for wall mount and tilted ceilings: rotate the lens base
(maximum 354°) until you are satisfied with the field of view.
1. Rotate 3D assembly in base for hori-
zontal adjustment
2. Loosen screw and adjust Tilt. Tighten
screw when desired vertical angle is
achieved.
3. Turn axis ring for horizontal rotation.
4. Focus lever
5. Zoom lever
ADJUST THE LENS
1. Loosen the focus lever (#4 on Fig 4.)
counter-clockwise a little and adjust for
optimum picture sharpness.
2. Loosen the zoom lever (#5 on Fig.4)
counter-clockwise a little and rotate to
determine the image view.
3. Re-tighten the zoom lever and focus lever
after adjustment.
Please note: It is important that you lock
the zoom and focus levers after making
adjustments. This will avoid the positions
moving (for example, from temperature changes or vibrations).
4. Once all adjustments are done, attach and secure the camera housing:
a. Use a soft and lint-free cloth to wipe the dome cover and remove
fingerprints.
b. Attach the inner liner (#3) to the tilt adjustment bracket (#2). Push down
until it clicks into place.
(Not applicable to IR models)
c. Assemble the dome cover (#4) and the camera base (#1).
To use the OSD joystick
control:
1. Press the OSD
joystick control
straight down to
enter the Main
menu or a selected
item.
2. Move the OSD
joystick control UP,
DOWN, LEFT and
RIGHT to navigate
through menus and
options.
1. OSD Joystick Control 2. Monitor Output
Figure 4. Camera Adjustment
Figure 5. Camera Adjustment Controls
Features/Model Do721 Do721R
ATR/D-WDR Digital Wide Dynamic Range On/Off (Selectable)
Multi language sup-
port
English, French, Spanish, Portuguese, German, Russian, Simpli-
fied Chinese, Japanese
DNR Yes
Signal system NTSC/PAL
Scanning system
NTSC 2:1 Interlace V: 59.94 Hz , H: 15.734KHz / PAL: 2:1 Inter-
lace V: 50 Hz , H: 15.625 KHz
Image sensor 1/3” SONY Exview HAD CCD II
Effective pixels NTSC: 976 (H) × 494 (V) / PAL: 976 (H) × 582 (V)
Lens Vari-focal, f=3.7mm~12mm
Vari-focal, f=2.8mm~10.5mm,
F1.2 DC iris
View angle (NTSC)
Wide: 82° (H), 56° (V)
Tele: 22° (H), 16° (V)
Wide: 93° (H), 66° (V)
Tele: 26°(H), 20° (V)
View angle (PAL)
Wide: 82° (H), 53° (V)
Tele: 24° (H), 15° (V)
Wide: 94° (H), 58° (V)
Tele: 26° (H), 16° (V)
Minimum illumination
F1.2 @50IRE, 0.02lux,
@30IRE, 0.01lux
B/W: 0 lux (IR on)
Sync system Internal
Horizontal resolution 700 TV lines
Privacy zone Yes, 8 zones (max)
Motion detection Yes, 4 areas (max)
Day & Night mode Digital Day/Night Mechanical Day/Night
White balance ATW/ Manual/ User/ Push/ Push lock
AGC, BLC
AGC: On / Off (selectable); BLC: Off/ BLC/ HLC (High light com-
pensation) (selectable)
Flickerless Auto adjusted
Gamma correction 0.45
OSD Yes
Video output level 1Vpp composite output, 75 ohm
S/N Ratio More than 50dB (AGC off)
Shutter time
NTSC: 1/60 sec
PAL: 1/50 sec
NTSC: 1/60~1/10K sec
PAL: 1/50~1/10K sec
Power supply
Power requirement DC 12V & AC 24V ± 10%
Power consumption 2.5W (max) 4W (max)
Environment
Operating temperature
-10ºC ~ 50ºC (14 ºF ~ 122 ºF); Supports -40ºC only when unit is
installed at temperature above -10ºC
Operating humidity 90% MAX
Storage temperature -20ºC ~ 60ºC (-4 ºF ~ 140 ºF)
Dimensions (øxH) ø140 x 132 mm (ø5.51” x 5.20”)
Weight approx. 975g (2.15 lb) approx. 958g (2.11 lb)
Protection Class CE, FCC, Class A, IP67, Vandal-Proof
Warranty
Standard Warranty i³ Superior 3 year warranty
IR
IR Distance N/A 15M (49ft)
IR LED N/A 14pcs
IR Wavelength N/A 850nm
IR turn on status N/A by photocell auto controlled
LEF Life N/A More than 10,000 hours (50ºC)
i
3
INTERNATIONAL INC.
1.866.840.0004
www.i3international.com
U.S.A 1967 Wehrle Drive,
Suite 1, PMB# 034 Buffalo
NY, 14221
Canada 780 Birchmount Road,
Unit 16, Scarborough,
ON, M1K 5H4
1
2
3
4
Figure 4. Lens Adjustment
OSD CONTROL SWITCH
  • Page 1 1
  • Page 2 2

i3 International Do721 Quick start guide

i3 International
Brand
i3 International
Model
Do721
Category
Security cameras
Type
Quick start guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents