i3 International i3-B732 Quick start guide
- Category
- Security cameras
- Type
- Quick start guide
• Power Supply
Ensure the supplied voltage meets the power consumption requirements of this
camera before powering the camera on. Incorrect voltage may cause irreparable
damage to the video camera and will effectively void the camera warranty.
• Cleaning
For maximum optical clarity, the camera dome or lens must remain clean. Use a -
soft, dry cloth to remove finger prints or dust from the dome cover.
Use a blower to remove dust from the lens. -
Clean the body with a soft, dry cloth. If it is very dirty, use a cloth dampened with a -
small quantity of neutral detergent, then wipe dry.
Do not use volatile solvents such as alcohol, benzene, or thinners, as they may -
damage the surface finishes.
• Servicing
To avoid electrical shock and to preserve the product warranty, DO NOT -
disassemble the camera. Refer servicing to qualified personnel only.
• Camera Parts
IR Bullet Camera i3-B732
Quick Start Guide
5
1
6
4
2
3
7
Camera main body1.
Sun shield2.
Externally adjustable focal length & focus3.
OSD menu joystick 4.
Mount bracket5.
BNC connector. Connects to the VIDEO IN connector of the Monitor Video Connector 6.
Power connector. Connects to the external power source. DC12V/AC24V7.
(Please refer to camera label)
• Camera Installation
Step 1. Mounting the camera
Place the “Guide Pattern Sticker” included with your purchase on the desired 1.
location.
Drill three holes on the installation surface and insert provided anchors into the 2.
pre-drilled holes.
Install the bracket base onto the installation surface and fasten securely using 3.
the provided screws.
If installing on a metal surface (e.g. metal pillar), use the enclosed rubber pad and
washer (optional) for isolation.
Step 2. Adjusting the camera angle
Loosen the adjustment screws and rotate the adjustment ring to loosen.
Adjust the angle for optimum image view. After the adjustment, re-tighten the
adjustment ring and re-fasten the adjustment screws.
Adjustment Ring
Adjustment Screws (2)
IR Bullet Camera
QUICK START GUIDE
PART NUMBER B732 IR BULLET CAMERA
Signal system NTSC, PAL
Image sensor 1/3” SONY Exview HAD CCD II
Scanning system 2:1 Interlace
NTSC: 59.94 Hz (V), 15.734KHz (H)
PAL: 50Hz (V), 15.625KHz (H)
Sync system Internal/Linelock
Horizontal resolution 700 TV line
Day / Night mode Mechanical (ICR) control (Auto/Color/Forced to BW)
Built-in lens f=3.3mm~12mm,F1.4 DC iris varifocal
IR-corrected lens
External adjustments (zoom and focus)
IRIS control N/A
Effective pixels No. NTSC: 976 (H) × 494 (V), PAL: 976 (H) × 582 (V)
Min. illumination F1.4 color mode: 0.03 lux@50 IRE, 0.015 lux@30
IRE, B/W mode: 0.015 lux@50 IRE, 0.0075
lux@30 IRE, 0 lux (IR LED Turn ON)
AGC, BLC, flickerless On / Off (selectable, Off/ BLC/ HLC (High Light
compensation (selectable), Yes
White balance ATW / Manual / User / Push / Push Lock
S/N ratio > 50dB (AGC off)
Angle of view Horizontal:89.8°(wide)~23.9°(tele)
Vertical:63.6°(wide)~17.9°(tele)°
WDR On / Off (selectable)
Video output 1Vpp composite output, 75 ohm
Gamma correction 0.45
Iris control DC
DNR Yes
Motion detection Yes, 4 areas (max)
IR LED Super power LED x28 pcs
IR wavelength 850nm
IR distance 35M (115 ft)
IR turn on status Under 10 lux by photocell auto controlled
LED life > 10,000 hours (50ºC/122ºF)
Privacy mask Yes, 8 zones (max)
Multi language English, Japanese, German, French, Russian,
Portuguese, Spanish, Simplified Chinese
ENVIRONMENT
Housing material Metal
Weight 610g (1.36 lb) approx.
Operating temperature -40°C ~ 50°C
Operating humidity 90% RH max
Storage temperature -20°C ~ 60°C (-4º~140º F)
Dimensions (øxH) ø82.9mm x 87mm x 205.5mm (3.26” x 3.43” x
8.09”)
Vandal resistance N/A
Protection class IP66
ELECTRICAL
Power requirement 12 VDC/24 VAC ±10%
Power consumption 7W (max.)
Electric shutter NTSC: 1/60 sec, PAL: 1/50 sec
WARRANTY
i³ Superior 3 year warranty
Step 3. Adjusting the camera lens
Loosen the lens adjustment screws (1) and (2) and slide the focus and lens angle sliders
to achieve optimum image view. After the adjustment, re-tighten the adjustment screws to
maintain the selected setting.
Slider (1) controls the lens focus, N (near), F (far).
Slider (2) controls the lens angle, T (tele), W (wide).
1
2
-
1
-
2
i3 International i3-B732 Quick start guide
- Category
- Security cameras
- Type
- Quick start guide
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
i3 International i3-B73X Series User manual
-
-
i3 International i3R505 & i3506HB User manual
-
-
-
-
-
