ZiLOG Z8F0113 User manual

Z8F0113
ZiLOG
Brand
ZiLOG
Model
Z8F0113
Type
User manual
Copyright ©2008 by Zilog
®
, Inc. All rights reserved.
www.zilog.com
User Manual
UM016608-0608
Z8F04A28100KITG
Z8 Encore! XP
®
F042A Series
Development Kit
Z8 Encore! XP
®
F042A Series Development Kit
User Manual
UM016608-0608
ii
Revision History
Each instance in the following table reflects a change to this document
from its previous revision. To see more detail, click the appropriate link in
the table.
Date
Revision
Level Description Page No
June
2008
08 Updated Hardware section. 1
May
2008
07 Removed Registration Card from
Documentation.
Added Z8F042ASJ020 to the Introduction
section.
2
1
March
2008
06 Changed document title to Z8 Encore! XP
®
F042A Series Development Kit.
Modified Table 2 in Schematics to incorporate
changes to R15 from 220 Ohm to 0 Ohm. Added
Note 3 to the Schematics.
All
10, 11
February
2008
05 Updated document with new Zilog logo and text.
Updated document disclaimer. Implemented
Style Guide.
All
December
2006
04 Changed Figure 14 to Figure 2. Updated
schematics.
5, 10
August
2006
03 Removed Serial from Serial Smart Cable. 1
October
2005
02 Updated schematic to reflect board revision C.
Added 20 MHz clock information, and updated
power supply circuit.
6, 10, 11
Z8 Encore! XP
®
F042A Series Development Kit
User Manual
UM016608-0608
iii
FCC Statement
This device complies with part 15 of the FCC Rules. Operation is subject
to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including
interference that may cause undesired operation.
Safeguards
The following precaution must be observed when working with the
devices described in this document:
Always use a grounding strap to prevent damage resulting from
electrostatic discharge (ESD).
Caution:
Z8 Encore! XP
®
F042A Series Development Kit
User Manual
Table of Contents UM016608-0608
iv
Table of Contents
Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Kit Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Software (on CD-ROM) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
System/Software Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Supported Host System Configuration . . . . . . . . . . . . . . . . . . 3
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Z8 Encore! XP
®
F042A Series
Development Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Z8 Encore! XP F042A Series MCU . . . . . . . . . . . . . . . . . . . . . . . 6
UART with IrDA Endec . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Power and Communication Interfaces . . . . . . . . . . . . . . . . . . . . . 8
External Interface Headers JP1 and JP2 . . . . . . . . . . . . . . . . . . . 8
Schematics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Customer Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Z8 Encore! XP
®
F042A Series Development Kit
User Manual
UM016608-0608 Introduction
1
Introduction
Zilog’s Z8 Encore! XP
®
F042A Series MCU is the part of the line of
Zilog
®
microcontroller products. The Z8 Encore! XP MCU Development
Kit (Z8F04A28100KITG) allows you to get familiar with the hardware
and software tools available with this product. This kit consists of the
4 KB version of the Z8 Encore!
®
Development Board that supports and
presents the features of the Z8 Encore! XP F042A Series. This kit allows
you to write application software and contains all supporting documents.
Z8F042ASJ020 is the silicon used in the board. For more details, refer to
Z8 Encore! XP
®
F0823 Series Product Specification (PS0243) available
for download at www.zilog.com
.
This manual acquaints you with the Z8 Encore! XP F042A Series MCU
Development Kit and provides instructions on setting up and using the
tools to start building designs and applications.
Kit Contents
The Z8 Encore! XP F042A Series MCU Development Kit contains the
following:
Hardware
The hardware in Z8 Encore! XP F042A Series Development Kit includes:
•
Z8 Encore! XP F042A Series Development Board
•
USB Smart Cable for PC to Z8 Encore! XP
®
F042A series
development board (previous versions of the development kit used a
Serial Smart Cable. Refer your original documentation for informa-
tion on using the Serial Smart Cable).
•
5 V DC power supply
Z8 Encore! XP
®
F042A Series Development Kit
User Manual
UM016608-0608 Introduction
2
Software (on CD-ROM)
The software on CD-ROM provided with Z8 Encore! XP
F042A Series
Development Kit includes:
•
ZDS II-Z8 Encore!
®
IDE with ANSI C-Compiler
•
Sample code
•
Document browser
•
Acrobat Reader
®
Figure 1. Z8 Encore! XP F042A Series Development Kit Contents
Development
Board
Packaging
CD-ROM Containing
Documentation
Serial Smart Cable
Power
Supply
Z8 Encore! XP
®
F042A Series Development Kit
User Manual
UM016608-0608 Introduction
3
Documentation
•
Quick Start Guide
•
Z8 Encore! XP F042A Series technical documentation (on CD-
ROM):
– Development Kit User Manual
– ZDS II - IDE User Manual
–eZ8
TM
CPU User Manual
The sample code is installed with ZDS II and resides in the
<installa-
tion directory>\samples
in the disk drive.
The documentation can be installed with the DemoShield interface or
can be viewed on the CD-ROM using the DemoShield menus and a PDF
reader. A copy of the Acrobat installer is provided on the CD-ROM and
can be installed from the DemoShield install screen. After installing the
documentation, Windows Explorer can be used to select any document to
be viewed with the PDF file viewer.
System/Software Requirements
An IBM PC (or compatible computer) with the following minimum
configuration:
Supported Host System Configuration
•
Win98 Second Edition/ WinNT 4.0 Service Pack 6/ Win2000 Service
Pack 3/ WinXP Professional Service Pack 1
•
PentiumII/233 MHz processor or higher up to Pentium IV, 2.8 GHz
•
96 MB RAM or more
•
25 MB hard disk space or more
•
Super VGA video adapter
Z8 Encore! XP
®
F042A Series Development Kit
User Manual
UM016608-0608 Introduction
4
•
CD-ROM
•
One or more RS-232 communication ports
Installation
Follow the instructions in the Quick Start Guide for software installation
and setup of the Z8 Encore! XP
®
F042A Series Development Kit.
Z8 Encore! XP
®
F042A Series Development Kit
User Manual
UM016608-0608 Z8 Encore! XP
®
F042A Series Development
5
Z8 Encore! XP
®
F042A Series
Development Board
The Z8 Encore! XP F042A Series Development Board is a development
and prototyping board for the Z8 Encore! XP F042A Series MCU. The
board provides a tool to evaluate features of Z8 Encore! XP F042A Series
MCU and to start developing an application before building the hardware.
Figure 2. Z8 Encore! XP F042A Series Development Board
Z8 Encore! XP
®
F042A Series Development Kit
User Manual
UM016608-0608 Z8 Encore! XP
®
F042A Series Development
6
Features
The features of Z8 Encore! XP F042A Series Development Board
include:
•
Z8 Encore!
®
MCU (28-pin SOIC)
•
3 LEDs
•
RS-232 interface
•
IrDA transceiver
•
Two pushbuttons, RESET and TEST
•
5 V DC power connector
•
On-Chip Debugger interface
•
20 MHz Crystal (Y1)
•
Header for ADC input
•
Prototyping area
•
External interface connectors JP1 and JP2
•
2.7 V to 3.6 V operating voltage with 5 V-tolerant inputs
Z8 Encore! XP F042A Series MCU
The Z8 Encore! XP F042A Series MCU is member of a family of Zilog
®
microcontroller products based on the 8-bit eZ8
TM
core CPU. The Flash
in-circuit programming capability allows for faster development time and
program changes in the field. The eZ8 core CPU is upward compatible
with existing Z8
®
instructions. The rich peripheral set of the Z8 Encore!
XP F042A Series makes it suitable for various applications including
motor control, security systems, home appliances, personal electronic
devices, and sensors.
Z8 Encore! XP
®
F042A Series Development Kit
User Manual
UM016608-0608 Z8 Encore! XP
®
F042A Series Development
7
The Development Board contains circuitry to support and present all the
features of the Z8 Encore! XP F042A Series. The main features of the
Z8 Encore! XP F042A Series include:
•
eZ8 core CPU
•
4 KB Flash memory with in-circuit programming capability
•
1 KB register RAM
•
5-channel, 10-bit Analog-to-Digital Converter (ADC)
•
Full-duplex UART
•
I
2
C interface (Master Mode only)
•
Serial Peripheral Interface (SPI)
•
Infrared Data Association (IrDA)-compliant infrared encoder/decoder
•
Two 16-bit timers with capture, compare, and PWM capability
•
Watchdog Timer (WDT) with internal RC oscillator
•
Eleven (20-pin package) or nineteen (28-pin package) I/O pins
•
Programmable priority interrupts
•
On-Chip Debugger (OCD)
•
Voltage Brownout Protection (VBO)
•
Power-On Reset (POR)
•
2.7 V to 3.6 V operating voltage with 5 V-tolerant inputs
•
Operating temperatures: 20 °C ±10 °C
For more information on the Z8 Encore! XP family of devices, refer to
Z8 Encore! XP
®
F0823 Series Product Specification (PS0243) available
for download at www.zilog.com
.
Z8 Encore! XP
®
F042A Series Development Kit
User Manual
UM016608-0608 Z8 Encore! XP
®
F042A Series Development
8
UART with IrDA Endec
The Z8 Encore! XP F042A Series (component U5) contains a fully-func-
tional, high-performance UART with Infrared Encoder/Decoder
(ENDEC). The Infrared Endec is integrated with an on-chip UART allow-
ing easy communication between the Z8 Encore! XP F042A Series and
IrDA transceivers. Infrared communication provides secure, reliable,
low-cost, point-to-point communication between PCs, PDAs, cell phones,
printers and other infrared enabled devices.
Power and Communication Interfaces
Table 1 provides jumper information concerning the shunt status,
functions, devices and defaults affected of jumpers JP3 and JP4.
External Interface Headers JP1 and JP2
External interface headers JP1 and JP2 are displayed in the schematic in
Figure 3 and Figure 4 on page 10.
Table 1. Jumpers JP3 and JP4
Jumper Status Device Affected Status Default
JP3* OUT RS-232 interface Enabled X
JP3 IN RS-232 interface Disabled
JP4* OUT IrDA interface Enabled
JP4 IN IrDA interface Disabled X
JP5 OUT U5 RESET
/PD0 PD0 (GPIO) X
JP5 IN U5 RESET
/PD0 RESET when
SW1 pressed
* These jumpers must not be OUT at the same time.
Z8 Encore! XP
®
F042A Series Development Kit
User Manual
UM016608-0608 Schematics
9
Schematics
This section provides schematics for the Z8 Encore! XP
®
F042A Series
D
evelopment Board.
10
Schematics UM016608-0608
Z8 Encore! XP
®
F042A Series Development Kit
User Manual
Figure 3. Schematic, Z8 Encore! XP F042A Series MCU Development Board, Page 1 of 2
5
5
4
4
3
3
2
2
1
1
D D
C C
B B
A A
PB0_ANA0 PB2_ANA2
VCC_33V
PB3_ANA3
GND
PB1_ANA1
PB3_ANA3
PB0_ANA0
PB4_ANA7
PB2_ANA2
A20
-CS0
A12
-IOREQ
-F91_WE
A13
GND
GND
A17
A21
VCC_33V
A14
D1
VCC_33V
D7
-DIS_FLASH
GND
A6 A0
D3
D6
-BUSACK
A3
D2
VCC_33V
A15
A4
-TRSTN
D0
-MREQ
A7
A10
A9
A16A18
A11
-INSTRD
A19
A5
GNDD5
-CS1
A22
A1A2
-CS2
-RD
A8
GND
D4
A23
-WR
-BUSREQ
GND
PB7
PA3_CTS0
PC7
VCC_33V
PC4
PA7_T1OUT PA2
PA1_T0OUT_JPGND
GND
PC5
PA4_RXD0 PA5_TXD0
GND
GND
PB6
PA0_T0IN_JP
PC6
PA6_nT1OUT
PA7_T1OUT
GNDVCC_33V
GND
-DIS_IrDA
PB1_ANA1
PA2
VCC_33V
GND
PA5_TXD0
PB1_ANA1 PB0_ANA0
DBG
PA3_CTS0
PA4_RXD0
PB2_ANA2
PB3_ANA3
PA0_T0IN
PC3_COUT
PA7_T1OUT
PC3_COUT
PC2_ANA6
PC1_ANA5
PC0_ANA4
PD0
PA6_nT1OUT
PC2_ANA6 PB4_ANA7
PC0_ANA4
PC1_ANA5
PC2_ANA6
PB6
PB7GND
PC5
PB2_ANA2
PA2
PC0_ANA4
PC2_ANA6
PA5_TXD0
PD0
PC3_COUT
PC1_ANA5
PA4_RXD0 PC4
VCC_33V
PC7
PA2
PA6_nT1OUT
PA1_T0OUT
PC6
PA3_CTS0
GND
PC1_ANA5
PA7_T1OUT
PB0_ANA0
GND
PA1_T0OUT
PB1_ANA1
PA0_T0IN
PB4_ANA7
PC0_ANA4
PB3_ANA3
DBG
PB4_ANA7 PC2_ANA6
PC0_ANA4
PB2_ANA2
PB0_ANA0
PC1_ANA5
PB3_ANA3
PB1_ANA1
PB5_JPPC3_COUT
PD0
GND
VCC_33V
VCC_33V
PA6_nT1OUT
-RESET
VCC_33V
PA0_T0IN_JP
PA1_T0OUT_JP
PB5
PB5_JP
GND
VCC_33V
DBG
-DIS_IRDA
-DIS_232
PA3_CTS0
PA4_RXD0
PA5_TXD0
SENSE
Title
Size Document Number Rev
Date: Sheet
of
96C0941-001 D
XP 4K MDS Processor Module. Schematic.
B
23Tuesday, March 18, 2008
Title
Size Document Number Rev
Date: Sheet
of
96C0941-001 D
XP 4K MDS Processor Module. Schematic.
B
23Tuesday, March 18, 2008
Title
Size Document Number Rev
Date: Sheet
of
96C0941-001 D
XP 4K MDS Processor Module. Schematic.
B
23Tuesday, March 18, 2008
connector 2
connector 1
for
reference
only
If Module is plugged onto the Dev Platform the local
RS232 interface is disabled by pin 50 of JP2
TEST
20 pin footprint
28 pin footprint
RESET/TEST2
Note 1:
PB6 and PB7 are dual function pins (GPIO or Analog supply)
R12, R13, R16, and R17 are zero-ohm resistors used in
conjunction with GPIO Control Registers to select function
desired. C21, C22, and C23 are bypass capacitors that are used
for better noise rejection. U8 is an optional filter that can
be used to improve the quality of the Analog Supply. The
development board is shipped configured for Analog Supply.
Table 1 shows the configurations recommended
NOTE 1:
NOTE 1:
NOTE 2
Note 2: The XP supports internal, external crystal, external
ceramic resonator, external R/C and external CMOS drive
clock modes. R14, R15, R18, C19, C20 and Y1 are used to
support the clock mode selected. The development board is
shipped configured for external 20MHz ceramic resonator or
internal clock operation. When using Internal oscilator,
pins 7 and 8 could be used as GPIO ports PA0 and PA1. To do
so install R20 and R21.
Table 2 shows the recommended clock mode configurations.
Clock Mode R14 R15 R18 C19 C20 Y1
Internal Only none none none none none none
Crystal 0 Ohm 0 Ohm none Yes Yes Yes
Ceramic Res 0 Ohm 0 Ohm none none none Yes
External CMOS none none none none none none
TABLE 2
(Use PA0_T0IN
pin on JP2)
Supply
R12 R13 R16 R17 R22 U8 C21...C23
Analog IN OUT IN OUT OUT optional IN
GPIO OUT IN OUT IN IN OUT OUT
TABLE 1
NOTE 3:
Resistors R20 and R21 are not populated. See Note 2.
C22
0.033uF
C22
0.033uF
R16
0
R16
0
R21
0
R21
0
R10
10
R10
10
R18
1M
R18
1M
C13
0.001uF
C13
0.001uF
R15
0
R15
0
R9
100K
R9
100K
R19
10K
R19
10K
D2
GREEN
D2
GREEN
21
SW1SW1
R22
0
R22
0
+
C23
30uF
+
C23
30uF
D3
YELL
D3
YELL
21
D4
RED
D4
RED
21
C17
0.001uF
C17
0.001uF
C21
0.033uF
C21
0.033uF
C11
0.001uF
C11
0.001uF
JP2
HEADER 30x2/SM
JP2
HEADER 30x2/SM
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
42
44
46
48
50
52
54
56
58
60
1
3
5
7
9
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
41
43
45
47
49
51
53
55
57
59
C16
0.001uF
C16
0.001uF
R17
0
R17
0
U5
Z8F04xA_28
U5
Z8F04xA_28
GND
9
PC4/LED
16
PA6/T1IN/T1OUT
15
PA5/TXD0
14
PA4/RXD0
13
PA3/CTS0
12
PB3/ANA3/CLKIN
4
PA0/T0IN/T0OUTXIN
7
VDD
6
PB1/ANA1
28
PB0/ANA0
27
PC1/ANA5/CINN/LED
24
PC2/ANA6/LED
25
PC3/COUT/LED
26
PC0/ANA4/CINP/LED
23
PB2/ANA2
1
PC6/LED
19
PC7/LED
20
PA2/DE
11
PB5/Vref
3
PB4/ANA7
2
PA7/T1OUT
18
PC5/LED
17
PB7(AGND)
10
PA1/T0OUT/XOUT
8
PB6(AVDD)
5
RESET/PD0
21
DBG
22
C14
0.001uF
C14
0.001uF
Y1
20 MHz
Y1
20 MHz
1
1
2
2
3
3
R12
0
R12
0
R7
100
R7
100
C15
0.001uF
C15
0.001uF
C19C19
R13
0
R13
0
J2
HEADER 8X2
J2
HEADER 8X2
2
4
6
8
10
12
14
16
1
3
5
7
9
11
13
15
R20
0
R20
0
R8
100
R8
100
U6
Z8F04xA
U6
Z8F04xA
PB2/ANA2
2
PA4/RXD0
10
PA3/CTS0
9
PA2/DE
8
PB3/CLKIN/ANA3
3
PA1/T0OUT/XOUT
6
PA0/T0IN/T0OUT/XIN/
5
PB0/ANA0
20
PB1/ANA1
1
PC1ANA5/CINN/LED
17
PC0/ANA4/CINP/LED
16
DBG
15
PA7/T1OUT
13
PA6/T1IN/T1OUT
12
PA5/TXD0
11
RESET/PD0
14
GND
7
VDD
4
PC3/COUT/LED
19
PC2/ANA6/LED
18
C12
0.001uF
C12
0.001uF
R14
0
R14
0
SW2SW2
C20C20
C10
0.001uF
C10
0.001uF
R11
100
R11
100
U8
EMI Filter
U8
EMI Filter
IO
1
GND
2
IO
3
JP5
HEADER 2
JP5
HEADER 2
1
2
JP1
HEADER 30x2/SM
JP1
HEADER 30x2/SM
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
42
44
46
48
50
52
54
56
58
60
1
3
5
7
9
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
41
43
45
47
49
51
53
55
57
59
C18
0.001uF
C18
0.001uF
11
Schematics UM016608-0608
Z8 Encore! XP
®
F042A Series Development Kit
User Manual
Figure 4. Schematic, Z8 Encore! XP F042A Series MCU Development Board, Page 2 of 2
5
5
4
4
3
3
2
2
1
1
D D
C C
B B
A A
TXD0
GND
CTS0
RXD0
VCC_33V
DBG
PA4_RXD0
PA5_TXD0
IRDA_SD
GND
PA3_CTS0
VCC_33V
GND
VCC_33V
PA5_TXD0
VCC_33V
PA4_RXD0
GND
VCC_33V
GND
-Z_RST
GND
GND
5V
VCC_33V
VCC
GND
-Z_RST
PA3_CTS0
DBG
-DIS_IRDA
-DIS_232
PA5_TXD0
PA4_RXD0
VCC_33V
GND
SENSE
Title
Size Document Number Rev
Date: Sheet
of
96C0941-001 D
XP 4K MDS Processor Module. Schematic.
B
33Wednesday, March 12, 2008
Title
Size Document Number Rev
Date: Sheet
of
96C0941-001 D
XP 4K MDS Processor Module. Schematic.
B
33Wednesday, March 12, 2008
Title
Size Document Number Rev
Date: Sheet
of
96C0941-001 D
XP 4K MDS Processor Module. Schematic.
B
33Wednesday, March 12, 2008
CONSOLE
GND
USER
DBG
INTERFACE
DIS RS232
DIS IRDA
3.3 OK
C2
0.1uF
C2
0.1uF
R3
68
R3
68
C4
0.1uF
C4
0.1uF
U3E
74LVC04/SO
U3E
74LVC04/SO
11 10
147
U3A
74LVC04/SO
U3A
74LVC04/SO
1 2
147
U7
LT1129-3.3/DD
U7
LT1129-3.3/DD
OUT
1
SENSE
2
GND
3
SHDN
4
VIN
5
C6
0.1uF
C6
0.1uF
JP3JP3
1
2
U3D
74LVC04/SO
U3D
74LVC04/SO
9 8
147
P2
Header 3x2
P2
Header 3x2
1 2
3 4
5 6
R2
10K
R2
10K
U3B
74LVC04/SO
U3B
74LVC04/SO
3 4
147
R23
10K
R23
10K
U3F
74LVC04/SO
U3F
74LVC04/SO
13 12
147
C1
0.1uF
C1
0.1uF
JP4JP4
1
2
C9
330nF
C9
330nF
R1
680
R1
680
F1
RXE050
F1
RXE050
R24
15K
R24
15K
R4
2R7
R4
2R7
C5
0.1uF
C5
0.1uF
J1
PWR JACK
J1
PWR JACK
2
3
1
U4
ZHX1810
U4
ZHX1810
TXD
2
SD
4
RXD
3
LEDA
1
VCC
5
GND
6
T
0
+
C7
100/10
+
C7
100/10
C8
0.1uF
C8
0.1uF
R5
10K
R5
10K
+
C3
100/10
+
C3
100/10
U3C
74LVC04/SO
U3C
74LVC04/SO
5 6
147
P1
DB9 Female
P1
DB9 Female
5
9
4
8
3
7
2
6
1
U1
MAX3222
U1
MAX3222
EN
1
C1+
2
C1-
4
C2+
5
C2-
6
T1IN
13
T2IN
12
R1OUT
15
R2OUT
10
V+
3
V-
7
T1OUT
17
T2OUT
8
R1IN
16
R2IN
9
SHDN
20
VCC
19
GND
18
NC
11
NC
14
TP1TP1
1
2
3
4
5
R6
10K
R6
10K
D1
LED
D1
LED
21
TP2TP2
1
2
3
4
5
Z8 Encore! XP
®
F042A Series Development Kit
User Manual
UM016608-0608 Customer Support
12
Customer Support
For answers to technical questions about the product, documentation, or
any other issues with Zilog’s offerings, please visit Zilog’s Knowledge
Base at:
http://www.zilog.com/kb
.
For any comments, detail technical questions, or reporting problems,
please visit Zilog’s Technical Support at:
h
ttp://support.zilog.com.
Z8 Encore! XP
®
F042A Series Development Kit
User Manual
UM016608-0608
13
DO NOT USE IN LIFE SUPPORT
LIFE SUPPORT POLICY
ZILOG'S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN
LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS PRIOR WRITTEN
APPROVAL OF THE PRESIDENT AND GENERAL COUNSEL OF ZILOG CORPORATION.
As used herein
Life support devices or systems are devices which (a) are intended for surgical implant
into the body, or (b) support or sustain life and whose failure to perform when properly
used in accordance with instructions for use provided in the labeling can be reasonably
expected to result in a significant injury to the user. A critical component is any
component in a life support device or system whose failure to perform can be reasonably
expected to cause the failure of the life support device or system or to affect its safety or
effectiveness.
Document Disclaimer
©2008 by Zilog, Inc. All rights reserved. Information in this publication concerning the
devices, applications, or technology described is intended to suggest possible uses and
may be superseded. ZILOG, INC. DOES NOT ASSUME LIABILITY FOR OR
PROVIDE A REPRESENTATION OF ACCURACY OF THE INFORMATION,
DEVICES, OR TECHNOLOGY DESCRIBED IN THIS DOCUMENT. ZILOG ALSO
DOES NOT ASSUME LIABILITY FOR INTELLECTUAL PROPERTY
INFRINGEMENT RELATED IN ANY MANNER TO USE OF INFORMATION,
DEVICES, OR TECHNOLOGY DESCRIBED HEREIN OR OTHERWISE. The
information contained within this document has been verified according to the general
principles of electrical and mechanical engineering.
Z8, Z8 Encore!, and Z8 Encore! XP are registered trademarks of Zilog, Inc. eZ8 is a
trademark of Zilog, Inc. All other product or service names are the property of their
respective owners.
Warning:
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17

ZiLOG Z8F0113 User manual

Z8F0113
ZiLOG
Brand
ZiLOG
Model
Z8F0113
Type
User manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents