Z8 Encore!
®
F083A Series Development Kit
User Manual
UM020604-0508 Revision History
ii
Revision History
Each instance in Revision History reflects a change to this document from
its previous revision. For more details, refer to the corresponding pages
and appropriate links in the table below.
Date
Revision
Level Description
Page
No
May 2008 04 Updated Introduction section. 1
March
2008
03 Modified Table 2 in Schematics to
incorporate changes to R15 from 220
Ohm to 0 Ohm. Added Note 3 to the
Schematics.
8, 9
December
2007
02 Updated Zilog logo, Zilog text, Disclaimer
section, and implemented style guide.
Removed XP from Z8 Encore! XP F0830/
F083A.
All
July 2006 01 Original issue. All
Z8 Encore!
®
F083A Series Development Kit
User Manual
UM020604-0508 Table of Contents
iii
Table of Contents
Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Kit Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Z8 Encore!
®
F083A Series Development Board . . . . . . . . . . . . . . . . 4
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
MCU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Jumper Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
External Interface Headers JP1 and JP2 . . . . . . . . . . . . . . . . . . . . . 6
Schematic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Customer Support. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Z8 Encore!
®
F083A Series Development Kit
User Manual
UM020604-0508 Introduction
1
Introduction
Zilog’s Z8 Encore!
®
F083A Series MCU is part of the line of Zilog
®
microcontroller products. The Z8 Encore! F083A Series MCU Develop-
ment Kit (Z8F083A0128ZCOG) enables you to become familiar with the
hardware and software tools available with this product. This kit consists
of the 8 KB version of the Z8 Encore! development board that supports
and presents the features of the Z8 Encore! F083A Series. This kit allows
you to write application software and contains all the supporting docu-
ments.
The Z8 Encore! F083A Series devices support up to 8 KB Flash Program
Memory and 256 B register RAM that is pin-for-pin compatible with the
award-winning Z8 Encore! XP F0822 Series Flash Microcontrollers
family.
The Z8 Encore! F083A Series device features up to eight channels of fast
analog-to-digital conversion (2.15 µs). The ADC on the Z8 Encore!
F083A is one of the fastest 10-bit ADCs available in a 28-pin or smaller
package. The Z8 Encore! F083A is built for speed to handle rigorous
application requirements for motor control, sensor interfacing, ballast
control, and appliance controls. The single-pin debugger and program-
ming interface simplifies code development and allows easy in-circuit
programming.
This user manual acquaints you with the Z8 Encore! F083A Series MCU
Development Kit, and gives instructions on setting up and using the tools
to start building designs and applications. Z8F083ASJ020 is the silicon
used in the board. For more information, refer to Z8 Encore!
®
F083A
Series Product Specification (PS0263).
Z8 Encore!
®
F083A Series Development Kit
User Manual
UM020604-0508 Introduction
2
Kit Contents
For information on kit contents, refer to Z8 Encore! XP
®
/Z8 Encore!
®
(F0822, F082A, F1680, and F083A Series) Development Kits Quick Start
Guide (QS0043).
Z8 Encore!
®
F083A Series Development Kit
User Manual
UM020604-0508 Installation
3
Installation
For software installation and setup of the Z8 Encore!
®
F083A Series
Development Kit, refer to Z8 Encore! XP
®
/Z8 Encore!
®
(F0822, F082A,
F1680, and F083A Series) Development Kits Quick Start Guide
(QS0043).
Z8 Encore!
®
F083A Series Development Kit
User Manual
UM020604-0508 Z8 Encore!
®
F083A Series
4
Z8 Encore!
®
F083A Series
Development Board
Introduction
The Z8 Encore!
®
F083A Series Development Board is a development and
prototyping board for the Z8 Encore! F083A Series MCU. The board pro-
vides a tool to evaluate features of Z8 Encore! F083A Series MCU, and to
start developing an application before building the hardware.
Figure 1. Z8 Encore!
®
F083A Series Development Board
(see
Schematic on page 7 for details on components not installed on this board)
Z8 Encore!
®
F083A Series Development Kit
User Manual
UM020604-0508 Z8 Encore!
®
F083A Series
5
Features
The key features of Z8 Encore! F083A Series include:
•
20 MHz eZ8 CPU
•
Up to 8 KB Flash memory with in-circuit programming capability
•
Up to 256 B register RAM
•
100 B non-volatile data storage (NVDS)
•
Up to 23 I/O pins depending upon package
•
Internal precision oscillator (IPO)
•
External crystal oscillator
•
Two enhanced 16-bit timers with capture, compare, and PWM capa-
bility
•
Watchdog Timer (WDT) with dedicated internal RC oscillator
•
Single-pin, On-Chip Debugger (OCD)
•
Fast 8-channel, 10-bit analog-to-digital converter (ADC)
•
On-chip analog comparator
•
Up to 18 vectored interrupts
•
Voltage Brownout (VBO) protection
•
Power-On Reset (POR)
•
2.7 V to 3.6 V operating voltage
•
Up to thirteen 5 V tolerant input pins
•
20- and 28-pin packages
•
0 °C to +70 °C standard temperature range and -40 °C to +105 °C
extended temperature operating ranges
Z8 Encore!
®
F083A Series Development Kit
User Manual
UM020604-0508 Z8 Encore!
®
F083A Series
6
MCU
The Z8 Encore! F083A Series MCU is member of a family of Zilog
®
microcontroller products based upon the 8-bit eZ8 core CPU. The Flash
in-circuit programming capability allows for faster development time and
program changes in the field. The eZ8 core CPU is upward compatible
with existing Z8
®
instructions. The successive approximation register
(SAR) ADC on the Z8 Encore! F083A is one of the fastest 10-bit ADCs
available in a 28-pin or smaller package. The Z8 Encore! F083A is built
for speed to handle rigorous application requirements for motor control,
sensor interfacing, ballast control, and appliance controls.
The development board contains circuitry to support and present all the
features of the Z8 Encore! F083A Series. For more information on the
Z8 Encore!
®
family of devices, refer to Z8 Encore!
®
F083A Series
Product Specification (PS0263) available for download at
w
ww.zilog.com.
Jumper Settings
The only jumper available on the Z8 Encore! F083A development board
is JP5, which affects U5 RESET/PD0. Set JP5 as follows:
•
JP5 OUT (default): PD0 (GPIO)
•
JP5 IN: RESET when SW1 pressed
External Interface Headers JP1 and JP2
Figure 2 on page 8 displays the external interface headers JP1 and JP2.
Z8 Encore!
®
F083A Series Development Kit
User Manual
UM020604-0508 Schematic
7
Schematic
This section includes schematics for the Z8 Encore!
®
F083A Series
Development Board (see Figure 2 and Figure 3 on page 9).
The following components appear in the schematic but are not installed
on the board:
•
C1, C2, C5, C6, C9, C11 through C18
•
JP3, JP4
•
P1
•
R2 through R5
•
U1, U3, U4
UM020604-0508
Z8 Encore!
®
F083A Series Development Kit
User Manual
8
Figure 2. Schematic, Z8 Encore!
®
F083A Series MCU Development Board
5
5
4
4
3
3
2
2
1
1
D D
C C
B B
A A
PB0_ANA0 PB2_ANA2
VCC_33V
PB3_ANA3
GND
PB1_ANA1
PB3_ANA3
PB0_ANA0
PB4_ANA7
PB2_ANA2
A20
-CS0
A12
-IOREQ
-F91_WE
A13
GND
GND
A17
A21
VCC_33V
A14
D1
VCC_33V
D7
-DIS_FLASH
GND
A6 A0
D3
D6
-BUSACK
A3
D2
VCC_33V
A15
A4
-TRSTN
D0
-MREQ
A7
A10
A9
A16A18
A11
-INSTRD
A19
A5
GNDD5
-CS1
A22
A1A2
-CS2
-RD
A8
GND
D4
A23
-WR
-BUSREQ
GND
PB7
PA3_CTS0
PC7
VCC_33V
PC4
PA7_T1OUT PA2
PA1_T0OUT_JPGND
GND
PC5
PA4_RXD0 PA5_TXD0
GND
GND
PB6
PA0_T0IN_JP
PC6
PA6_nT1OUT
PA7_T1OUT
GNDVCC_33V
GND
-DIS_IrDA
PB1_ANA1
PA2
VCC_33V
GND
PA5_TXD0
PB1_ANA1 PB0_ANA0
DBG
PA3_CTS0
PA4_RXD0
PB2_ANA2
PB3_ANA3
PA0_T0IN
PC3_COUT
PA7_T1OUT
PC3_COUT
PC2_ANA6
PC1_ANA5
PC0_ANA4
PD0
PA6_nT1OUT
PC2_ANA6 PB4_ANA7
PC0_ANA4
PC1_ANA5
PC2_ANA6
PB6
PB7GND
PC5
PB2_ANA2
PA2
PC0_ANA4
PC2_ANA6
PA5_TXD0
PD0
PC3_COUT
PC1_ANA5
PA4_RXD0 PC4
VCC_33V
PC7
PA2
PA6_nT1OUT
PA1_T0OUT
PC6
PA3_CTS0
GND
PC1_ANA5
PA7_T1OUT
PB0_ANA0
GND
PA1_T0OUT
PB1_ANA1
PA0_T0IN
PB4_ANA7
PC0_ANA4
PB3_ANA3
DBG
PB4_ANA7 PC2_ANA6
PC0_ANA4
PB2_ANA2
PB0_ANA0
PC1_ANA5
PB3_ANA3
PB1_ANA1
PB5_JPPC3_COUT
PD0
GND
VCC_33V
VCC_33V
PA6_nT1OUT
-RESET
VCC_33V
PA0_T0IN_JP
PA1_T0OUT_JP
PB5
PB5_JP
GND
VCC_33V
DBG
-DIS_IRDA
-DIS_232
PA3_CTS0
PA4_RXD0
PA5_TXD0
SENSE
Title
Size Document Number Rev
Date: Sheet
of
96C0941-001 D
XP 4K MDS Processor Module. Schematic.
B
23Tuesday, March 18, 2008
Title
Size Document Number Rev
Date: Sheet
of
96C0941-001 D
XP 4K MDS Processor Module. Schematic.
B
23Tuesday, March 18, 2008
Title
Size Document Number Rev
Date: Sheet
of
96C0941-001 D
XP 4K MDS Processor Module. Schematic.
B
23Tuesday, March 18, 2008
connector 2
connector 1
for
reference
only
If Module is plugged onto the Dev Platform the local
RS232 interface is disabled by pin 50 of JP2
TEST
20 pin footprint
28 pin footprint
RESET/TEST2
Note 1:
PB6 and PB7 are dual function pins (GPIO or Analog supply)
R12, R13, R16, and R17 are zero-ohm resistors used in
conjunction with GPIO Control Registers to select function
desired. C21, C22, and C23 are bypass capacitors that are used
for better noise rejection. U8 is an optional filter that can
be used to improve the quality of the Analog Supply. The
development board is shipped configured for Analog Supply.
Table 1 shows the configurations recommended
NOTE 1:
NOTE 1:
NOTE 2
Note 2: The XP supports internal, external crystal, external
ceramic resonator, external R/C and external CMOS drive
clock modes. R14, R15, R18, C19, C20 and Y1 are used to
support the clock mode selected. The development board is
shipped configured for external 20MHz ceramic resonator or
internal clock operation. When using Internal oscilator,
pins 7 and 8 could be used as GPIO ports PA0 and PA1. To do
so install R20 and R21.
Table 2 shows the recommended clock mode configurations.
Clock Mode R14 R15 R18 C19 C20 Y1
Internal Only none none none none none none
Crystal 0 Ohm 0 Ohm none Yes Yes Yes
Ceramic Res 0 Ohm 0 Ohm none none none Yes
External CMOS none none none none none none
TABLE 2
(Use PA0_T0IN
pin on JP2)
Supply
R12 R13 R16 R17 R22 U8 C21...C23
Analog IN OUT IN OUT OUT optional IN
GPIO OUT IN OUT IN IN OUT OUT
TABLE 1
NOTE 3:
Resistors R20 and R21 are not populated. See Note 2.
C22
0.033uF
C22
0.033uF
R16
0
R16
0
R21
0
R21
0
R10
10
R10
10
R18
1M
R18
1M
C13
0.001uF
C13
0.001uF
R15
0
R15
0
R9
100K
R9
100K
R19
10K
R19
10K
D2
GREEN
D2
GREEN
21
SW1SW1
R22
0
R22
0
+
C23
30uF
+
C23
30uF
D3
YELL
D3
YELL
21
D4
RED
D4
RED
21
C17
0.001uF
C17
0.001uF
C21
0.033uF
C21
0.033uF
C11
0.001uF
C11
0.001uF
JP2
HEADER 30x2/SM
JP2
HEADER 30x2/SM
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
42
44
46
48
50
52
54
56
58
60
1
3
5
7
9
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
41
43
45
47
49
51
53
55
57
59
C16
0.001uF
C16
0.001uF
R17
0
R17
0
U5
Z8F04xA_28
U5
Z8F04xA_28
GND
9
PC4/LED
16
PA6/T1IN/T1OUT
15
PA5/TXD0
14
PA4/RXD0
13
PA3/CTS0
12
PB3/ANA3/CLKIN
4
PA0/T0IN/T0OUTXIN
7
VDD
6
PB1/ANA1
28
PB0/ANA0
27
PC1/ANA5/CINN/LED
24
PC2/ANA6/LED
25
PC3/COUT/LED
26
PC0/ANA4/CINP/LED
23
PB2/ANA2
1
PC6/LED
19
PC7/LED
20
PA2/DE
11
PB5/Vref
3
PB4/ANA7
2
PA7/T1OUT
18
PC5/LED
17
PB7(AGND)
10
PA1/T0OUT/XOUT
8
PB6(AVDD)
5
RESET/PD0
21
DBG
22
C14
0.001uF
C14
0.001uF
Y1
20 MHz
Y1
20 MHz
1
1
2
2
3
3
R12
0
R12
0
R7
100
R7
100
C15
0.001uF
C15
0.001uF
C19C19
R13
0
R13
0
J2
HEADER 8X2
J2
HEADER 8X2
2
4
6
8
10
12
14
16
1
3
5
7
9
11
13
15
R20
0
R20
0
R8
100
R8
100
U6
Z8F04xA
U6
Z8F04xA
PB2/ANA2
2
PA4/RXD0
10
PA3/CTS0
9
PA2/DE
8
PB3/CLKIN/ANA3
3
PA1/T0OUT/XOUT
6
PA0/T0IN/T0OUT/XIN/
5
PB0/ANA0
20
PB1/ANA1
1
PC1ANA5/CINN/LED
17
PC0/ANA4/CINP/LED
16
DBG
15
PA7/T1OUT
13
PA6/T1IN/T1OUT
12
PA5/TXD0
11
RESET/PD0
14
GND
7
VDD
4
PC3/COUT/LED
19
PC2/ANA6/LED
18
C12
0.001uF
C12
0.001uF
R14
0
R14
0
SW2SW2
C20C20
C10
0.001uF
C10
0.001uF
R11
100
R11
100
U8
EMI Filter
U8
EMI Filter
IO
1
GND
2
IO
3
JP5
HEADER 2
JP5
HEADER 2
1
2
JP1
HEADER 30x2/SM
JP1
HEADER 30x2/SM
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
42
44
46
48
50
52
54
56
58
60
1
3
5
7
9
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
41
43
45
47
49
51
53
55
57
59
C18
0.001uF
C18
0.001uF
UM020604-0508
Z8 Encore!
®
F083A Series Development Kit
User Manual
9
Figure 3. Schematic, Z8 Encore!
®
F083A Series MCU Development Board
5
5
4
4
3
3
2
2
1
1
D D
C C
B B
A A
TXD0
GND
CTS0
RXD0
VCC_33V
DBG
PA4_RXD0
PA5_TXD0
IRDA_SD
GND
PA3_CTS0
VCC_33V
GND
VCC_33V
PA5_TXD0
VCC_33V
PA4_RXD0
GND
VCC_33V
GND
-Z_RST
GND
GND
5V
VCC_33V
VCC
GND
-Z_RST
PA3_CTS0
DBG
-DIS_IRDA
-DIS_232
PA5_TXD0
PA4_RXD0
VCC_33V
GND
SENSE
Title
Size Document Number Rev
Date: Sheet
of
96C0941-001 D
XP 4K MDS Processor Module. Schematic.
B
33Wednesday, March 12, 2008
Title
Size Document Number Rev
Date: Sheet
of
96C0941-001 D
XP 4K MDS Processor Module. Schematic.
B
33Wednesday, March 12, 2008
Title
Size Document Number Rev
Date: Sheet
of
96C0941-001 D
XP 4K MDS Processor Module. Schematic.
B
33Wednesday, March 12, 2008
CONSOLE
GND
USER
DBG
INTERFACE
DIS RS232
DIS IRDA
3.3 OK
C2
0.1uF
C2
0.1uF
R3
68
R3
68
C4
0.1uF
C4
0.1uF
U3E
74LVC04/SO
U3E
74LVC04/SO
11 10
147
U3A
74LVC04/SO
U3A
74LVC04/SO
1 2
147
U7
LT1129-3.3/DD
U7
LT1129-3.3/DD
OUT
1
SENSE
2
GND
3
SHDN
4
VIN
5
C6
0.1uF
C6
0.1uF
JP3JP3
1
2
U3D
74LVC04/SO
U3D
74LVC04/SO
9 8
147
P2
Header 3x2
P2
Header 3x2
1 2
3 4
5 6
R2
10K
R2
10K
U3B
74LVC04/SO
U3B
74LVC04/SO
3 4
147
R23
10K
R23
10K
U3F
74LVC04/SO
U3F
74LVC04/SO
13 12
147
C1
0.1uF
C1
0.1uF
JP4JP4
1
2
C9
330nF
C9
330nF
R1
680
R1
680
F1
RXE050
F1
RXE050
R24
15K
R24
15K
R4
2R7
R4
2R7
C5
0.1uF
C5
0.1uF
J1
PWR JACK
J1
PWR JACK
2
3
1
U4
ZHX1810
U4
ZHX1810
TXD
2
SD
4
RXD
3
LEDA
1
VCC
5
GND
6
T
0
+
C7
100/10
+
C7
100/10
C8
0.1uF
C8
0.1uF
R5
10K
R5
10K
+
C3
100/10
+
C3
100/10
U3C
74LVC04/SO
U3C
74LVC04/SO
5 6
147
P1
DB9 Female
P1
DB9 Female
5
9
4
8
3
7
2
6
1
U1
MAX3222
U1
MAX3222
EN
1
C1+
2
C1-
4
C2+
5
C2-
6
T1IN
13
T2IN
12
R1OUT
15
R2OUT
10
V+
3
V-
7
T1OUT
17
T2OUT
8
R1IN
16
R2IN
9
SHDN
20
VCC
19
GND
18
NC
11
NC
14
TP1TP1
1
2
3
4
5
R6
10K
R6
10K
D1
LED
D1
LED
21
TP2TP2
1
2
3
4
5
Z8 Encore!
®
F083A Series Development Kit
User Manual
UM020604-0508 Customer Support
10
Customer Support
For answers to technical questions about the product, documentation, or
any other issues with Zilog’s offerings, please visit Zilog’s Knowledge
Base at http://www.zilog.com/kb
.
For any comments, detail technical questions, or reporting problems,
please visit Zilog’s Technical Support at http://support.zilog.com
.
Z8 Encore!
®
F083A Series Development Kit
User Manual
UM020604-0508
11
DO NOT USE IN LIFE SUPPORT
LIFE SUPPORT POLICY
ZILOG'S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL
COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE
EXPRESS PRIOR WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL
COUNSEL OF ZILOG CORPORATION.
As used herein
Life support devices or systems are devices which (a) are intended for surgical implant
into the body, or (b) support or sustain life and whose failure to perform when properly
used in accordance with instructions for use provided in the labeling can be reasonably
expected to result in a significant injury to the user. A critical component is any
component in a life support device or system whose failure to perform can be reasonably
expected to cause the failure of the life support device or system or to affect its safety or
effectiveness.
Document Disclaimer
©2008 by Zilog, Inc. All rights reserved. Information in this publication concerning the
devices, applications, or technology described is intended to suggest possible uses and
may be superseded. ZILOG, INC. DOES NOT ASSUME LIABILITY FOR OR
PROVIDE A REPRESENTATION OF ACCURACY OF THE INFORMATION,
DEVICES, OR TECHNOLOGY DESCRIBED IN THIS DOCUMENT. ZILOG ALSO
DOES NOT ASSUME LIABILITY FOR INTELLECTUAL PROPERTY
INFRINGEMENT RELATED IN ANY MANNER TO USE OF INFORMATION,
DEVICES, OR TECHNOLOGY DESCRIBED HEREIN OR OTHERWISE. The
information contained within this document has been verified according to the general
principles of electrical and mechanical engineering.
Z8 Encore! and Z8 Encore! XP are registered trademarks of Zilog, Inc. All other product
or service names are the property of their respective owners.
Warning:
/
