Zonet ZFS3216E Quick Installation Manual

Brand: Zonet

Model: ZFS3216E

Type: Quick Installation Manual

ZFS3216E/ZFS3224E

Quick Installation Guide

All manuals and user guides at all-guides.com

all-guides.com

Features

Plug & Play

Complies with IEEE802.3, IEEE802.3u, IEEE802.3ab, IEEE802.3x standards

NWAY Auto-negotiation support, Auto-Sense the transmission speed, half/full duplex

16/24 ports 10/100/1000M Auto-Sense, Auto-MDI/MDIX

Adopt IEEE802.3x flow control for full-duplex and backpressure for half-duplex

Store and forward structure

MAC address auto learning

Support IEEE802.3x for broadcasting storm control

Package Contents

One 16/24 Ports Gigabit Switch

One Quick Installation Guide

One Power Adapter

Four rubber pads

Two L

-shape rackmount brackets and screws

Front Panel

LED lights panel

LED Status Operation

Power Green

Steady: Power is ON

10/100M Link Green

Steady: Indicates a 10/100M device is connected

Flash: the port is transmitting/receiving data

Off: Indicates

either a 10M device or no device connected

Full Duplex

(FDX/COL)

Green

Steady: Indicates

this port is working under

full duplex mode

Flash:

Indicates there is data collision at this port

Off: Indicates

this port is working under

half duplex mode

1000M Link/Act

Green

Steady: Indicates a Gigabit device is connected

Flash: the port is transmitting/receiving data

Off: Indicates

either a 10/100M device or no device connected

Front Panel Diagrams

ZFS3216E(top) / ZFS3224E(bottom)

Rear Panel

AC power line socket and power switch

Side Panel

Ventilation and cooling holes

Please make sure there are no substances blocking up these holes, and leave enough space on both sides of

the switch, so the switch can have proper ventilation and cooling to avoid over heat inside the unit, which

may cause damages and/or system malfunctions.

All manuals and user guides at all-guides.com

Installation

1. Connect the output power to the AC-inlet of the Switch

2. Connect other IEEE802.3 compatible network device (Hub, Switch, PC) to RJ-45 port of the Switch using

Category 3/4/5 UTP/STP cables.

3. Connect another IEEE802.3 compatible network device (Hub, Switch, PC) to another RJ-45 port of the Switch

by following the same process as described in Step2.

Caution

The switch must put on a surface that is able to withstand at least 5Kgs weight.

The power line should be properly and tightly connect with the switch power socket and power supply socket.

Make sure ventilation and cooling is sufficient for the switch; suggested at least 10cm space in distance

around the unit.

Don’t put any heavy items on top of the switch.

Power supply requirement: 160-240VAC 50/60HZ, grounded connection

Don’t installing the switch at high electromagnetic environment, under direct sunlight, dust and vibrate

surfaces.

Install all four(4) rubber pads at the bottom corners of the switch to avoid scratch at the bottom surface.

When installs it on the rack, make sure to fix tight it on the rack with the screw.

Maximum cable distance between the Switch and other IEEE802.3 compatible network devices is 100 meters

Only Category 3/4/5 cables can be used in 10 Mbps operation mode.

Must use an Unshielded/Shielded Twisted-Pair (UTP/STP) Category 5 cable or higher Grade data cables in

order to operate 100Mbps and 1000Mbps network operations.

May experience loss of data packets when Category 3 or 4 cables are used.

Auto-MDIX ports allow all kinds of IEEE802.3 compatible network devices, such as hub, switch and

computers, to connect to the Switch using straight-through wires and/or crossover cables.

Troubleshooting

We always do our best to deliver high quality products to our customers; however, problems may still occur

when using the product. Many problems are due to disconnected cables, faulty cables, exceeded maximum

cable length, or malfunctioning NIC. Below are some troubleshooting tips you may try when the switch is not

functioning correctly.

1. Check power to see if it functions properly.

Make sure the power switch is turned on and the power LED is on steady. If the Power LED is not ON, check

the power source and power cable.

2.Check connection to see if it is done correctly and properly between computers and switch or between

switches. Make sure all devices are connected to the network properly and the Link LED is ON on connected

ports.

3.Check the NIC to see if it is installed and function properly.

4.Check the cable length to see if it reaches the maximum distance.

5.Check straight-through and/or crossover, cable collision, domain limitation, and other physical installation

aspects to see if they meet standard network installation requirements.

Notice:

If problem still persists and cannot be solved, write down your software/hardware configuration and error

indications from LEDs and call your local retailer or the store purchased for further assistance.

All manuals and user guides at all-guides.com

Zonet ZFS3216E Quick Installation Manual

Zonet ZFS3216E Quick Installation Manual

Zonet ZFS3216E Quick Installation Manual

Related papers

Other documents