Zonet ZFS3015P Quick Installation Manual

Brand: Zonet

Model: ZFS3015P

Type: Quick Installation Manual

All manuals and user guides at all-guides.com

all-guides.com

P

P

a

a

c

c

k

k

a

a

g

g

e

e

C

C

o

o

n

n

t

t

e

e

n

n

t

t

s

s

• One ZFS3015P / ZFS3018P

• One Quick Installation Guide

• One Power Adapter

Contact your local authorized reseller or the store purchased from for any items

damaged and/or missing.

T

T

o

o

p

p

P

P

a

a

n

n

e

e

l

l

LED indicators

LED Status

Operation

Power Green

Steady: Power is ON

LNK/ACT Green

Steady: Network cable connected and connection established

Flash: Data packets are transmitting

Off: Network cable is unplug

Diagram

a. ZFS3015P

Note: Power Connector is on the marked side of ZFS3015P

All manuals and user guides at all-guides.com

b. ZFS3018P

Note: Power Connector is on the marked side of ZFS3018P

R

R

e

e

a

a

r

r

P

P

a

a

n

n

e

e

l

l

a. ZFS3015P

5 RJ-45 ports

b. ZFS3018P

8

RJ-45 ports

All manuals and user guides at all-guides.com

I

I

n

n

s

s

t

t

a

a

l

l

l

l

a

a

t

t

i

i

o

o

n

n

1. Connect the provided power adapter to the Power connector of the ZFS3015P /

ZFS3018P

2. Connect your network devices to the RJ-45 ports of the ZFS3015P / ZFS3018P

with UTP/STP Category 3/4/5 cables

C

C

a

a

u

u

t

t

i

i

o

o

n

n

• The switch must put on a surface that is able to hold at least 5kgs weight

• Power adapter must be connected to the switch properly and securely

• Suggested at least 10cm empty space around the unit for sufficient ventilation

and cooling

• Do not recommend to put any items on top of the switch

• ZFS3015P / ZFS3018P is not ideally to work in a high electromagnetic

environment, under direct sunlight, dust and vibrating surfaces

• Maximum distance between the switch and the end node is 100 meters

• Must use an unshielded or shielded twisted-pair (UTP/STP) Category 5 or

better cables to ensure proper transmission

• Loss of data packet may encounter when using cable other than Category 5

All manuals and user guides at all-guides.com

T

T

r

r

o

o

u

u

b

b

l

l

e

e

s

s

h

h

o

o

o

o

t

t

i

i

n

n

g

g

1. Check the power adapter and power wall-jet to make sure they are function

properly. Check if the switch is turned-ON and power LED is steady.

2. Check all cable connections between computer and the switch to make sure

they are connected properly.

3. Maximum distance is 100 meters from the switch to end nodes.

4. Link LED(s) is ON/flashing at the connected port(s) of the switch.

5. Test your computer’s network adapter to make sure it is installed and functioned

properly.

6. Check issues such as network collisions, domain limitations, and other physical

installation aspects. Make sure they all meet IEEE standard network

installation requirements, more details can be found at www.ieee.org.

7. If problem still persists, write down your software/hardware configuration and

LED error indications and contact your local retailer or the store purchased for

further assistance.

8. If the provided power adapter is missing, purchase 9V / 600mA power adapter

for replacement.

All manuals and user guides at all-guides.com

1
2
3
4
5

Zonet ZFS3015P Quick Installation Manual

Brand: Zonet

Model: ZFS3015P

Type: Quick Installation Manual

Related papers

Other documents