Zonet ZFS3228E Quick Installation Manual

Brand: Zonet

Model: ZFS3228E

Type: Quick Installation Manual

ZFS3228E

Quick Installation Guide

Features

Plug & Play

Complies with IEEE802.3, IEEE802.3u, IEEE802.3ab, IEEE802.3x standards

NWAY Auto-negotiation support, Auto-Sense the transmission speed, half/full duplex

8 ports 10/100/1000M Auto-Sense, Auto-MDI/MDIX

Adopt IEEE802.3x flow control for full-duplex and backpressure for half-duplex

Non-blocking wire-speed transfer

Adopt store and forward structure

MAC address auto learning

Support IEEE802.3x for broadcasting storm control

Package Contents

One 8-Port Gigabit Switch

One Quick Installation Guide

One Power Adapter

Four rubber pad

Front Panel

LED lights panel

LED Status Operation

Power Green

Lit: Power is on

10/100M Link Green

Lit: Indicates a 10/100M device is connected

Flash: the port is transmitting/receiving data

Not lit: Indicates

there’s a 10M device or no device connected

Full Duplex

(FDX/COL)

Green

Lit: Indicates

this port is working under

full duplex mode

Flash: the port is

working under half duplex mode

Not lit: Indicates

this port is working under

half duplex mode

1000M Link/Act

Green

Lit: Indicates a 1000M device is connected

Flash: the port is transmitting/receiving data

Not lit: Indicates

there’s a 10/100M device or no device connected

Rear Panel

RJ45 ports

Side Panel

Ventilation and cooling holes

Please make sure there is no substance block up these holes, and leave enough space at the two side of

the switch, so the switch can have a proper ventilation and cooling to avoid high heat inside the switch,

which may cause improper working of the system.

Installation

1. Connect the output power to the AC-inlet of the Switch

2. Connect other IEEE802.3 compatible network device (Hub, Switch, PC) to one port of the Switch using

Category 3/4/5 UTP/STP cabling

3. Connect another IEEE802.3 compatible network device (Hub, Switch, PC) to another port of the Switch by

following the same process as described in Step2.

Caution

The surface to put the switch should be able to withstand at least 5Kgs weight

The power line should be properly and tightly connect with the switch power socket and power supply socket.

Make sure there has good ventilation around the switch; and don’t put any heavy item on the switch

Power supply requirement: 160-240VAC 50/60HZ, a good ground connection

Avoid installing the switch at high electromagnetic environment or under direct sunlight, avoiding dust and

vibrations.

Leave 10cm distance at least with other items around the switch to ensure a good ventilation and cooling.

Install the four rubber pad one the four bottom corner of the switch to avoid scratch at the bottom surface.

When install the switch on the rack, make sure to fix tight it on the rack with the screw.

The cable distance between the Switch and other IEEE802.3 compatible network device should not exceed

100 meter

Make sure the wiring is correct, it can be used Category 3/4/5 cable in 10 Mbps operation.

To reliably operate your network at 100/1000Mbps, you must use an Unshielded/shielded Twisted-Pair

(UTP/STP) Category 5 cable, or better Data Grade cabling.

While a Category 3 or 4 cable may initially seem to work, it will soon cause data loss

All kinds of IEEE802.3 compatible network device (Hub, Switch, PC)can connect to the Switch by using

straight-through wires or crossover wires because of Switch’s auto MDIX function

Troubleshooting

We always do our very best to deliver good quality product. However, the problem may still occur when you use

the product.

Most problems come from disconnected cable, faulty cable, exceeding cable length, or a malfunctioning LAN

card.

1. Check power to see if it functions properly.

Make sure the power switch is set on and the Power LED is lit. If the Power LED is not lit after the power is

turned on, check the power source and power cable. If the problem still can not be resolved, call your local

supplier to change the power adapter or the whole Switch unit.

2.Check if connection is done properly between

computers and switch or between switches.

Make sure all devices are connected to the network

properly and the Link LED is lit on each connected port.

3.Check the LAN card if it is installed properly.

4.Check the cable length, straight-through/cross-

over, collision domain limitation, and other physical aspects of the installation to see if they meet the network

installation requirements.

Notice:

If the problem still can not be solved, have your software/hardware configuration and error indications from

LEDs, call your local supplier for further assistance.

12-086-00599 Rev:00

Zonet ZFS3228E Quick Installation Manual

Zonet ZFS3228E Quick Installation Manual

Zonet ZFS3228E Quick Installation Manual

Related papers

Other documents