Axis P5532 User manual

Category
Security cameras
Type
User manual

This manual is also suitable for

ENGLISH DEUTSCH
ITALIANO
ESPAÑOL
INSTALLATION GUIDE
FRAN
Ç
AIS
AXIS P5532 PTZ Dome Network Camera
AXIS P5534 PTZ Dome Network Camera
Legal Considerations
Video and audio surveillance can be prohibited by laws
that vary from country to country. Check the laws in
your local region before using this product for
surveillance purposes.
This product includes one (1) H.264 decoder license. To
purchase further licenses, contact your reseller.
Electromagnetic Compatibility (EMC)
This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there is
no guarantee that interference will not occur in a
particular installation.
If this equipment does cause harmful interference to
radio or television reception, which can be determined
by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or
more of the following measures: Re-orient or relocate
the receiving antenna. Increase the separation between
the equipment and receiver. Connect the equipment to
an outlet on a different circuit to the receiver. Consult
your dealer or an experienced radio/TV technician for
help. Shielded (STP) network cables must be used with
this unit to ensure compliance with EMC standards.
USA
- This equipment has been tested and found to
comply with the limits for a Class B computing device
pursuant to Subpart B of Part 15 of FCC rules, which are
designed to provide reasonable protection against such
interference when operated in a commercial
environment. Operation of this equipment in a
residential area is likely to cause interference, in which
case the user at his/her own expense will be required to
take whatever measures may be required to correct the
interference.
Canada
- This Class B digital apparatus complies with
Canadian ICES-003
Europe - This digital equipment fulfills the requirements
for radiated emission according to limit B of EN55022,
and the requirements for immunity according to
EN55024 residential and commercial industry.
Japan - This is a class B product based on the standard
of the Voluntary Control Council for Interference from
Information Technology Equipment (VCCI). If this is used
near a radio or television receiver in a domestic
environment, it may cause radio interference. Install and
use the equipment according to the instruction manual.
Australia - This electronic device meets the
requirements of the Radio communications
(Electromagnetic Compatibility) Standard AS/NZS
CISPR22:2002.
Korea - Class B: As this equipment has obtained EMC
registration for household use, it can be used in any area
including residential areas.
Safety
Complies to EN 60950-1 (IEC 60950-1), Safety of
Information Technology Equipment.
Equipment Modifications
This equipment must be installed and used in strict
accordance with the instructions given in the user
documentation. This equipment contains no
user-serviceable components. Unauthorized equipment
changes or modifications will invalidate all applicable
regulatory certifications and approvals.
Liability
Every care has been taken in the preparation of this
document. Please inform your local Axis office of any
inaccuracies or omissions. Axis Communications AB
cannot be held responsible for any technical or
typographical errors and reserves the right to make
changes to the product and documentation without
prior notice. Axis Communications AB makes no
warranty of any kind with regard to the material
contained within this document, including, but not
limited to, the implied warranties of merchantability
and fitness for a particular purpose. Axis
Communications AB shall not be liable nor responsible
for incidental or consequential damages in connection
with the furnishing, performance or use of this material.
RoHS
This product complies with both the European
RoHS directive, 2002/95/EC, and the Chinese
RoHS regulations, ACPEIP.
WEEE Directive
The European Union has enacted a Directive
2002/96/EC on Waste Electrical and Electronic
Equipment (WEEE Directive). This directive is
applicable in the European Union member
states.
The WEEE marking on this product (see right) or its
documentation indicates that the product must not be
disposed of together with household waste. To prevent
possible harm to human health and/or the environment,
the product must be disposed of in an approved and
environmentally safe recycling process. For further
information on how to dispose of this product correctly,
contact the product supplier, or the local authority
responsible for waste disposal in your area.
Business users should contact the product supplier for
information on how to dispose of this product correctly.
This product should not be mixed with other commercial
waste.
Support
Should you require any technical assistance, please
contact your Axis reseller. If your questions cannot be
answered immediately, your reseller will forward your
queries through the appropriate channels to ensure a
rapid response. If you are connected to the Internet, you
can:
• download user documentation and firmware updates
• find answers to resolved problems in the FAQ database.
Search by product, category, or phrases
• report problems to Axis support by logging in to your
private support area.
AXIS P5532/P5534 uses a 3.0V CR2032 Lithium battery,
for more information please see page 111.
AXIS P5532/P5534 Installation Guide Page 3
ENGLISH
AXIS P5532 & AXIS P5534
Installation Guide
This installation guide provides instructions for installing an AXIS P5532/AXIS P5534 PTZ Dome
Network Camera on your network. For all other aspects of using the product, please see the User’s
Manual, available on the CD included in this package, or from www.axis.com
Installation Steps
1. Check the package contents against the list below.
2. Hardware overview. See page 4.
3. Install the hardware.
Prepare for installation, see page 6.
Hard ceiling mount, see page 7.
Drop ceiling mount, see page 8.
Bracket mount (optional accessory), see page 10.
Install the AXIS T8123 High PoE Midspan 1-port, see page 11.
4. Assign an IP address. See page 12.
5. Set the password. See page 15.
Package Contents
Item Models/variants/notes
Network camera AXIS P5532
AXIS P5534
Dome covers Clear transparent cover (pre-mounted)
Smoked transparent cover
Mounting kit Mounting kit for hard ceilings and drop ceilings
Resitorx screw driver
High PoE Midspan AXIS T8123
CD AXIS Network Video Product CD, including product documentation,
installation tools and other software.
Printed materials AXIS P5532/P5534 Network Camera Installation Guide (this document),
Axis Warranty Document, Drill template, Extra serial number labels (2x),
AVHS Authentication key
Optional accessories AXIS T91A Mounting Accessories
Multi-connector cable for connection of I/O, audio, and power
See www.axis.com for information on power accessories and outdoor housings
Important!
This product must be used in
compliance with local laws and
regulations.
Page 4 AXIS P5532/P5534 Installation Guide
Hardware Overview
SDHC card slot
Status indicator LED
Restart button
Control button
Dome ring
Dome ring
Dome cover Top cover
screws (6)
Sealing ring
Camera unit
Dome cover
AXIS P5532/P5534 Installation Guide Page 5
ENGLISH
Hard ceiling mount
Drop ceiling mount
Bracket arm
Bracket arm
Mounting plate
screw (3)
Camera base lid
Multi-connector
Hook for safety wire
Network connector
Top cover screws (4)
Top cover
Unit holders (3)
(3)
Mounting
plate screws
(3)
Camera base lid screws (4)
Cable tracks
Foam gasket
Part number (P/N) & Serial number (S/N).
The serial number may be required
during the installation.
and
washer (3)
Trim ring
Safety wire
Page 6 AXIS P5532/P5534 Installation Guide
Install the hardware
Prepare for installation
Read all the instructions before preparing to install AXIS P5532/P5534 since several installation
preparation steps require removing the top cover and would benefit from being completed together.
Follow the instructions Remove the protective packaging, below to remove the protective
packing before installing the camera.
The camera is supplied with a clear transparent cover and a smoked transparent cover. If
required, follow the instructions Replace the clear/smoked dome cover (optional), below to
replace the dome cover.
A standard or high capacity SD card (not included) is required to store images locally in the
network camera. Follow the instructions Install an SD card (optional), below to remove the
top cover and install an SD card.
Remove the protective packaging
1. Loosen the 4 top cover screws and remove the top cover, see illustration on page 5.
2. Remove the protective packaging.
3. If replacing the clear/smoked dome cover or installing an SD card, refer to the instructions
Replace the clear/smoked dome cover (optional) and Install an SD card (optional), below.
4. Put the top cover back in its original position and fasten the screws.
!
IMPORTANT! - To use AXIS P5532/P5534 outdoors, it must be installed in an approved
outdoor housing. Please see www.axis.com for more information on outdoor housing.
Protective packaging
AXIS P5532/P5534 Installation Guide Page 7
ENGLISH
Replace the clear/smoked dome cover (optional)
1. Loosen the 4 top cover screws and remove the top cover, see illustration on page 5.
2. Remove the 6 dome ring screws and remove the dome ring from the top cover.
3. Attach the dome ring and the dome cover to the top cover and secure by tightening the 6
screws.
4. If installing an SD card, refer to the instructions Install an SD card (optional), below.
5. Put the top cover back in its original position and fasten the screws.
Note:
Be careful not to scratch or damage the dome cover. Use a soft cloth to wipe clean before
attaching the dome cover to the camera unit.
Install an SD card (optional)
1. Loosen the 4 top cover screws and remove the top cover, see illustration on page 5.
2. Insert an SD card (not included) into the SDHC (Secure Digital High Capacity) card slot.
3. Put the top cover back in its original position and fasten the screws.
Note:
The SD card is automatically mounted when inserted into the SDHC card slot. However,
before removing the SD card it should be unmounted through the camera’s web pages. Go
to Setup > System Options > Storage > SD Card and click Unmount. For more informa-
tion, please see the User’s Manual available from the AXIS Network Video Product CD sup-
plied with this product or from the website at www.axis.com
Hard ceiling mount
1. Prepare the ceiling for installation of the mounting plate, use the supplied drill template to
position the holes. Make sure to use drill bits, screws, and plugs that are appropriate for the
material.
2. Install the mounting plate.
3. Loosen the 4 camera base lid screws and remove the camera base lid, see illustration on page 5.
Mounting plate
Security wire
Page 8 AXIS P5532/P5534 Installation Guide
4. Route and connect the network cable and the multi-connector cable, if applicable, to the
network camera. Be careful not to damage the cables when connecting them. Make sure the
foam gasket holes are aligned with the cable tracks and, if applicable, remove the cut-out piece
for the multi-connector cable from the foam gasket.
5. Put the camera base lid back in its original position and fasten the screws.
6. Secure the camera using the supplied safety wire.
7. Slide the unit holders on the network camera into the slots on the mounting plate and rotate
the camera unit.
8. Install the High PoE Midspan 1-Port, see Install the AXIS T8123 High PoE Midspan 1-port, on
page 11.
9. Check that the indicator LEDs on the midspan indicate the correct conditions, see the table on
page 21 for further details.
Drop ceiling mount
1. Remove the ceiling tile in which the drop ceiling mount is to be fitted.
2. Use the supplied template to mark the position for the 210 mm (8.3 in.) hole in the ceiling tile.
Cut around the template.
Notes:
The combined weight of the camera and ceiling mount is approximately 2.3 kg (5.1 lb.). Check
that the ceiling material is strong enough to support this weight.
The ceiling tile should be 5 mm–60 mm (0.2 in.–2.4 in.) thick.
3. Assemble the ceiling bracket.
4. Put the ceiling bracket into the ceiling tile, see illustration on page 9.
5. Tighten the bracket arm screws using a torx 20 screwdriver head.
6. Loosen the 4 camera base lid screws and remove the camera base lid, see illustration on page 5.
Ceiling tile
Hole diameter
210 mm (8.3 in.)
AXIS P5532/P5534 Installation Guide Page 9
ENGLISH
7. Route and connect the network cable and the multi-connector cable, if applicable, to the
network camera. Be careful not to damage the cables when connecting them. Make sure the
foam gasket holes are aligned with the cable tracks and, if applicable, remove the cut-out piece
for the multi-connector cable from the foam gasket.
8. Put the camera base lid back in its original position and fasten the screws.
9. Secure the camera using the supplied safety wire.
10. Slide the unit holders on the network camera into the slots on the mounting plate and rotate
the camera unit.
11. Install the High PoE Midspan 1-Port, see Install the AXIS T8123 High PoE Midspan 1-port, on
page 11.
12. Check that the indicator LEDs on the midspan indicate the correct conditions. See the table on
page 21 for further details.
13. Install the ceiling tile, with the camera mounted, into the ceiling.
Multi-connector cable
Network cable
Safety wire
Ceiling tile
Ceiling bracket
Page 10 AXIS P5532/P5534 Installation Guide
14. Place the trim ring over the ceiling bracket and snap it into place.
Bracket mount (optional accessory)
1. Install the selected bracket according to the
instructions supplied with the bracket. If drilling is
required, make sure to use drill bits, screws, and
plugs that are appropriate for the material.
2. Loosen the 4 camera base lid screws and remove
the camera base lid, see illustration on page 5.
3. Route the network cable and the multi-connector
cable, if applicable, through the holes in the
mounting bracket.
4. Hook the camera to the safety wire on the bracket.
5. Connect the network cable and, if applicable, the
multi-connector cable to the network camera.
6. Install AXIS T8123, see Install the AXIS T8123 High PoE Midspan 1-port, on page 11.
7. Put the camera base lid back in its original position.
8. Slide the unit holders on the network camera into the slots on the bracket and rotate the
camera unit.
9. Secure the network camera to the mounting bracket by fastening the 3 screws (Torx T30).
Trim ring
Wall bracket (mounting example)
Safety
wire
Slots for
Screws
Torx T30
unit holders
AXIS P5532/P5534 Installation Guide Page 11
ENGLISH
Install the AXIS T8123 High PoE Midspan 1-port
AXIS T8123 High PoE Midspan 1-port enables Axis network video products with high power
consumption to receive data and power over the same Ethernet cable. Follow these instructions to
connect AXIS T8123.
1. Connect AXIS T8123 (Data in) to the network switch using a standard network cable.
2. Connect AXIS T8123 (Data and Power Out) to the network camera, using the network cable that
has been connected to the camera.
3. Connect AXIS T8123 to an AC outlet (100–240 V AC), using the supplied power cable.
For information on the LEDs on the midspan, see AXIS T8123 Status indicators, on page 21.
Data &
Power out
Data in
Port
AC Input
connectivity
indicator
connectivity
indicator
Network camera Ethernet
AXIS T8123
Page 12 AXIS P5532/P5534 Installation Guide
Assign an IP Address
Most networks today have a DHCP server that automatically assigns IP addresses to connected
devices. If your network does not have a DHCP server the network camera will use 192.168.0.90 as
the default IP address.
If you would like to assign a static IP address, the recommended method in Windows is either AXIS
IP Utility or AXIS Camera Management. Depending on the number of cameras you wish to install,
use the method that best suits your purpose.
Both of these free applications are available on the AXIS Network Video Product CD supplied with
this product, or they can be downloaded from www.axis.com
Notes:
If assigning the IP address fails, check that there is no firewall blocking the operation.
For other methods of assigning or discovering the IP address, e.g. in other operating systems, see
page 17.
Method Recommended for Operating system
AXIS IP Utility
See page 13
Single camera
Small installations
Windows
AXIS Camera Management
See page 14
Multiple cameras
Large installations
Installation on a different subnet
Windows 2000
Windows XP Pro
Windows 2003 Server
Windows Vista
Windows 7
AXIS P5532/P5534 Installation Guide Page 13
ENGLISH
AXIS IP Utility - single camera/small installation
AXIS IP Utility automatically discovers and displays Axis devices on your network. The application
can also be used to manually assign a static IP address.
Note that the computer running AXIS IP Utility must be on the same network segment (physical
subnet) as the network camera.
Automatic discovery
1. Check that the network camera is connected to the network and that power has been applied.
2. Start AXIS IP Utility.
3. When the camera appears in the window, double-click it to open its home page.
4. See page 15 for instructions on how to assign the password.
Assign the IP address manually (optional)
1. Acquire an unused IP address on the same network segment as your computer.
2. Select the network camera in the list.
3. Click the Assign new IP address to the selected device button
and enter the IP address.
4. Click Assign and follow the on-screen instructions. Note that the camera must be restarted
within 2 minutes for the new IP address to be set.
5. Click Home Page to access the camera’s web pages.
6. See page 15 for instructions on how to set the password.
Page 14 AXIS P5532/P5534 Installation Guide
AXIS Camera Management - multiple cameras/large installations
AXIS Camera Management can automatically discover multiple Axis devices, show connection
status, manage firmware upgrades and set IP addresses.
Automatic discovery
1. Check that the camera is connected to the network and that power has been applied.
2. Start AXIS Camera Management. When the network camera appears in the window, right-click
the link and select Live View Home Page.
3. See page 15 for instructions on how to set the password.
Assign an IP address in a single device
1. Select the network camera in AXIS Camera Management and
click the Assign IP button.
2. Select Assign the following IP address and enter the IP
address, subnet mask and default router the device will use.
3. Click OK.
Assign IP addresses in multiple devices
AXIS Camera Management speeds up the process of assigning
IP addresses to multiple devices, by suggesting IP addresses
from a specified range.
1. Select the devices you wish to configure (different models
can be selected) and click the Assign IP button.
2. Select Assign the following IP address range and enter
the range of IP addresses, the subnet mask and default
router the devices will use.
3. Click Update. Suggested IP addresses are listed under New
IP Addresses and can be edited by selecting a device and
clicking Edit.
4. Click OK.
AXIS P5532/P5534 Installation Guide Page 15
ENGLISH
Set the Password
To gain access to the product, the password for the default administrator user root must be set. This
is done in the ‘Configure Root Password’ dialog, which is displayed when the network camera is
accessed for the first time.
To prevent network eavesdropping when setting the root password, this can be done via an
encrypted HTTPS connection, which requires an HTTPS certificate.
Note: HTTPS (Hypertext Transfer Protocol over SSL) is a protocol used to encrypt the traffic between web
browsers and servers. The HTTPS certificate controls the encrypted exchange of information.
To set the password via a standard HTTP connection, enter it directly in the first dialog shown
below.
To set the password via an encrypted HTTPS connection, follow these steps:
1. Click the Create self-signed certificate button.
2. Provide the requested information and click OK. The certificate is created and the password can
now be set securely. All traffic to and from the network camera is encrypted from this point on.
3. Enter a password and then re-enter it to confirm the spelling. Click OK. The password has now
been configured.
4. To log in, enter the user name “root” in the dialog as requested.
Note: The default administrator user name root cannot be deleted.
5. Enter the password as set above, and click OK.
Note: If the password is lost, the camera must be reset to the factory default settings. See page 22.
To configure the password directly
via an unencrypted connection, enter
the password here.
To create an HTTPS connection,
start by clicking this button.
Page 16 AXIS P5532/P5534 Installation Guide
Access the video stream
The Live View page of the network camera is displayed, with links to the Setup tools, which allow
you to customize the camera.
If required, click Yes to install AMC (AXIS Media Control), which allows viewing of the video stream
in Internet Explorer. You will need administrator rights on the computer to do this.
If required, click the link to install missing decoders.
Note: To install AMC in Windows 7/Windows Vista, you must run Internet Explorer as an administrator.
Right-click the Internet Explorer icon and select Run as administrator.
AXIS P5532/P5534 Installation Guide Page 17
ENGLISH
Other Methods of Setting the IP address
The table below shows the other methods available for setting or discovering the IP address. All
methods are enabled by default, and all can be disabled.
Use in operating
system
Notes
AVHS Service
Connection
All To connect the camera to an AVHS service, refer to the service
provider´s Installation Guide. For information and help to find a local
AVHS Service Provider go to www.axis.com
UPnP™
Windows When enabled on your computer, the camera is automatically detected
and added to “My Network Places.”
Bonjour
MAC OSX
(10.4 or later)
Applicable to browsers with support for Bonjour. Navigate to the Bon-
jour bookmark in your browser (e.g. Safari) and click on the link to
access the camera’s web pages.
AXIS Dynamic
DNS Service
All A free service from Axis that allows you to quickly and simply install
your camera. Requires an Internet connection with no HTTP proxy. See
www.axiscam.net for more information
ARP/Ping
All See below. The command must be issued within 2 minutes of
connecting power to the camera.
DHCP
All To view the admin pages for the network DHCP server, see the server’s
own documentation.
Page 18 AXIS P5532/P5534 Installation Guide
Set the IP address with ARP/Ping
1. Acquire an IP address on the same network segment your computer is connected to.
2. Locate the serial number (S/N) on the product label on the camera.
3. Open a command prompt on your computer and enter the following commands:
4. Check that the network cable is connected to the camera and then start/restart the camera, by
disconnecting and reconnecting power.
5. Close the command prompt when you see ‘Reply from 192.168.0.125: ...’ or similar.
6. In your browser, type in http://<IP address> in the Location/Address field and press Enter on
your keyboard.
Notes:
To open a command prompt in Windows: from the Start menu, select Run... and type cmd. Click OK.
To use the ARP command in Windows 7/ Windows Vista, right-click the command prompt icon and
select Run as administrator.
To use the ARP command on a Mac OS X, use the Terminal utility in Application > Utilities.
Windows syntax: Windows example:
arp -s <IP Address> <Serial Number>
ping -l 408 -t <IP Address>
arp -s 192.168.0.125 00-40-8c-18-10-00
ping -l 408 -t 192.168.0.125
UNIX/Linux/Mac syntax: UNIX/Linux/Mac example:
arp -s <IP Address> <Serial Number> temp
ping -s 408 <IP Address>
arp -s 192.168.0.125 00:40:8c:18:10:00 temp
ping -s 408 192.168.0.125
AXIS P5532/P5534 Installation Guide Page 19
ENGLISH
Unit Connectors
Network connector – RJ-45 Ethernet connector. Supports High PoE (Power over Ethernet, IEEE
802.3at). Use AXIS T8123 High PoE Midspan 1-port (included). Shielded cables should be used to
comply with EMC.
Multi-connector – Terminal connector for connection of external equipment:
Audio equipment
Input/output (I/O) devices
AC/DC power supply
When connecting external equipment to AXIS P5532/P5534, a multi-connector cable is required in
order to maintain the IP51 rating. The multi-connector cable can be purchased from your Axis
reseller. For more information, please see the User’s Manual available from the AXIS Network Video
Product CD supplied with this product or from the website at www.axis.com
SDHC card slot – A standard or high capacity SD card (not included) is required to store images
locally in the network camera. To insert and remove the SD card, the camera’s top cover must be
removed, see Install an SD card (optional), on page 7.
Note:
Before removal, the SD card should be unmounted to prevent corruption of recordings. To
unmount the SD card, go to Setup > System Options > Storage > SD Card and click
Unmount. For more information, please see the User’s Manual available from the AXIS Net-
work Video Product CD supplied with this product or from the website at www.axis.com
Page 20 AXIS P5532/P5534 Installation Guide
Multi-connector cable (not included)
When connecting external equipment to AXIS P5532/P5534, a multi-connector cable is required in
order to maintain the camera’s IP51 rating. The multi-connector cable can be purchased from your
Axis reseller.
Connect the multi-connector cable to the camera’s multi connector, see illustration on page 5 and
instructions on page 7 and page 8. The cable provides the following connectors:
Power connector – 3-pin terminal block used for power input.
Audio in (pink) – 3.5 mm input for a mono microphone, or a line-in mono signal (left channel is
used from a stereo signal).
Audio out (green) – 3.5 mm output for audio (line level) that can be connected to a public address
(PA) system or an active speaker with a built-in amplifier. A pair of headphones can also be
attached. A stereo connector must be used for the audio out.
I/O terminal connector – Used in applications for e.g. motion detection, event
triggering, time lapse recording and alarm notifications. In addition to an auxiliary
power and a GND pin, the I/O terminal connector has 4 pins that can be
configured as either input or output. These pins provide the interface to:
Digital output - For connecting external devices such as relays and LEDs. Connected devices
can be activated by the VAPIX® Application Programming Interface, output buttons on the
Live View page or by an Event Type. The output will show as active (shown under
Events > Port Status if the alarm device is activated.
DC power input, 24-34 V DC
AC power input, 20-24 V AC
AXIS P5532: max 15 W
AXIS P5534: max 17 W
AXIS P5532: max 20 VA
AXIS P5534: max 23.6 VA
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112

Axis P5532 User manual

Category
Security cameras
Type
User manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI