Abus TVIP51500 User manual

2

Deutsch

Diese Bedienungsanleitung enthält wichtige Hinweise zur Inbetriebnahme und Handhabung. Achten

Sie hierauf, auch wenn Sie dieses Produkt an Dritte weitergeben.

Heben Sie deshalb diese Bedienungsanleitung zum Nachlesen auf!

Eine Auflistung der Inhalte finden Sie im Inhaltsverzeichnis mit Angabe der entsprechenden Seitenzahlen auf

Seite 3

These user manual contains important information for installation and operation.

This should be noted also when this product is passed on to a third party.

Therefore look after these operating instructions for future reference!

A list of contents with the corresponding page numbers can be found in the index on page 74

Ce mode d’emploi appartient à de produit. Il contient des recommandations en ce qui concerne sa

mise en service et sa manutention. Veuillez en tenir compte et ceci également lorsque vous remettez

le produit à des tiers.

Conservez ce mode d’emploi afin de pouvoir vous documenter en temps utile!

Vous trouverez le récapitulatif des indications du contenu á la table des matières avec mention de la page

correspondante á la page140.

Deze gebruiksaanwijzing hoort bij dit product. Er staan belagrijke aanwijzingen in betreffende de

ingebruikname en gebruik, ook als u dit product doorgeeft aan derden.

Bewaar deze hendleiding zorgvuldig, zodat u deze later nog eens kunt nalezen!

U vindt een opsomming van de inhoud in de inhoudsopgave met aanduiding van de paginanummers op

pagina 211

Denne manual hører sammen med dette produkt. Den indeholder vigtig information som skal bruges

under opsætning og efterfølgende ved service. Dette skal huskes også når produkter gives videre til

anden part.

Læs derfor denne manual grundigt igennem også for fremtiden.

Indholdet kan ses med sideanvisninger kan findes i indekset på side 283

Deutsch

English

Français

Dansk

Nederlands

8

Deutsch

6.19 Systemlog ............................................................................................................................................. 70

7. Wartung und Reinigung ....................................................................................................................... 71

7.1 Funktionstest ........................................................................................................................................ 71

7.2 Reinigung .............................................................................................................................................. 71

8. Entsorgung ........................................................................................................................................... 71

9. Technische Daten ................................................................................................................................. 72

10. URL Kommandos ................................................................................................................................. 73

11. GPL Lizenzhinweise ............................................................................................................................. 73

Appendix ...................................................................................................................................................... 353

A.) Frame and Bitrates ............................................................................................................................. 353

B.) Storage calculation ............................................................................................................................ 356

C.) HTTP/CGI Command .......................................................................................................................... 358

English

TVIP51500/TVIP51550

 User manual

Version 11/2012

75

English

Contents

1. Usage in accordance with regulations ............................................................................................... 77

2. Scope of delivery .................................................................................................................................. 77

3. Installation ............................................................................................................................................. 78

3.1 Power supply ........................................................................................................................................ 78

3.2 Installing the camera ............................................................................................................................ 78

4. Camera description .............................................................................................................................. 78

4.1 Front view .............................................................................................................................................. 78

4.2 Rear view ............................................................................................................................................... 79

4.3 Alarm input and output ........................................................................................................................ 80

4.4 Status displays ..................................................................................................................................... 80

4.5 Putting into operation .......................................................................................................................... 81

4.6 Accessing the network camera for the first time .............................................................................. 82

4.7 Accessing the network camera over a web browser ........................................................................ 83

4.8 Installing the ActiveX plug-in .............................................................................................................. 83

4.9 Adjusting the security settings ........................................................................................................... 83

4.10 Password prompt ................................................................................................................................. 84

4.11 Accessing the network camera over an RTSP player ...................................................................... 84

4.12 Accessing the network camera over a mobile phone ...................................................................... 85

4.13 Accessing the network camera over ABUS VMS .............................................................................. 86

5. User functions ...................................................................................................................................... 87

5.1 Audio / video control ............................................................................................................................ 90

6. Camera settings (configuration) ......................................................................................................... 92

6.1 System ................................................................................................................................................... 93

6.2 Camera .................................................................................................................................................. 95

6.3 Network ............................................................................................................................................... 102

6.4 Security ............................................................................................................................................... 109

6.5 PTZ control .......................................................................................................................................... 112

6.6 Preset position .................................................................................................................................... 113

6.7 Patrol ................................................................................................................................................... 115

6.8 FTP client ............................................................................................................................................ 116

6.9 SMTP .................................................................................................................................................... 118

6.10 Network storage ................................................................................................................................. 120

6.11 SD-Card ............................................................................................................................................... 123

6.12 HTTP event .......................................................................................................................................... 129

6.13 Alarm output ....................................................................................................................................... 130

6.14 Schedule .............................................................................................................................................. 131

6.15 Alarm input .......................................................................................................................................... 132

6.16 Alarm buffer ........................................................................................................................................ 132

6.17 Motion detection ................................................................................................................................. 133

76

English

6.18 Audio detection .................................................................................................................................. 134

6.19 System Log ......................................................................................................................................... 136

7. Servicing and cleaning ...................................................................................................................... 137

7.1 Function test ....................................................................................................................................... 137

7.2 Cleaning .............................................................................................................................................. 137

8. Disposal ............................................................................................................................................... 137

9. Technical data ..................................................................................................................................... 138

10. URL commands .................................................................................................................................. 139

11. GPL Lizenzhinweise ........................................................................................................................... 139

Appendix ...................................................................................................................................................... 353

A.) Frame and Bitrates ............................................................................................................................. 353

B.) Storage calculation ............................................................................................................................ 356

C.) HTTP/CGI Command .......................................................................................................................... 358

77

English

1. Usage in accordance with regulations

The network camera is equipped with a high-quality CCD element. It is used for indoor video surveillance. In

order to use the camera outdoors, it must be installed in a suitable weatherproof housing.

The product must not be exposed to moisture. The video surveillance camera

is only designed for use in dry rooms.

Use of this product for other than the described purpose may lead to damage to the product

and other dangers. All other uses are not in accordance with regulations, and result in the

invalidation of the product guarantee and warranty. No liability can be accepted as a result.

This also applies to any alterations or modifications made to the product.

Read the entire operating manual carefully before putting the product into operation. The

operating manual contains important information on installation and operation.

2. Scope of delivery

ABUS network camera

TVIP51500/TVIP51550

Power supply unit

Camera bracket

Antenna

(TVIP51550)

Quick guide

Network cable (1 metre)

Software CD

(including operating manual)

78

English

3. Installation

Make sure that all accessories and parts listed above are present in the scope of delivery. An Ethernet cable

is required for camera operation. This Ethernet cable must meet UTP Category 5 (CAT 5) specifications and

must not be longer than 100 metres.

3.1 Power supply

Before starting installation, ensure that the mains voltage and the rated voltage on the camera are identical.

3.2 Installing the camera

Firstly, the supplied base is fastened to the bottom of the camera. The plate is then aligned to the pre-defined

screw openings and fastened with the screws provided.

IMPORTANT!

The camera must be disconnected from the mains power during installation.

4. Camera description

4.1 Front view

Focus ring: Adjust the camera focus (image sharpness) by turning the ring.

Power LED: The LED is lit when in operation.

Network LED: When the camera is connected to a network, the LED flashes during data exchange.

Light Sensor

WLAN

A

ntenna

Back Focus ring

DC drive connector

79

English

4.2 Rear view

Alarm input / output: One alarm input / output (see diagram below).

LAN interface: Used for establishing a network connection via the RJ-45 plug.

Audio output: Audio output via connected loudspeakers (two-way audio).

Audio input: Used for connecting a separate microphone.

Reset: Manual restart or reset to factory settings (see table).

Power supply: Connection for 12 V PSU.

WLAN antenna: Used for establishing a wireless network connection (WLAN 802.11 b/g).

Camera reset:

Reset button pressed once briefly Camera is restarted

Reset button held down for 10 seconds Camera reset to the factory settings

Power LED

Power connector

SD-Card-Slot

I/O terminal

A

udio input

Ethernet connecto

r

Reset

Status LED SD-Card

WLAN LED

A

udio output

80

English

4.3 Alarm input and output



I/O Connector

PIN Description

1 Ground

2 + 12 VDC

3 RS-485 -

4 RS-485 +

5 Digital Output 1

6 Digital Output 2

7 Alarm Input 1

8 Alarm Input 2

Please carefully observe the connection instructions and power specifications!

4.4 Status displays

Status LEDs

State / LED colour Power LED

(blue)

Network LED

(red / blue)

System start On Blue flashing

Switched off Off Off

Network problem On Red (constantly lit)

Alarm Input 1/2: max. 12 VDC

Digital Output 1/2: max. 12V / 100mA

8 7 6 5 4 3 2 1

81

English

4.5 Putting into operation

The network camera automatically detects whether a direct connection between the PC and camera should

be made. A cross-over network cable is not required for this. You can use the supplied patch cable for direct

connection when putting into operation for the first time.

Direct connection of the network camera to a PC / laptop

6. Ensure that a CAT 5 network cable is used.

7. Connect the cable to the Ethernet interface of the PC / laptop and the network camera.

8. Connect the power supply to the network camera.

9. Configure the network interface of your PC / laptop to the IP address 192.168.1.1 and the default

gateway to 192.168.1.2.

10. Go to point 4.6 to finish the initial set-up and establish the connection to the network camera.

Connecting the network camera to a router / switch

8. Ensure that a CAT 5 network cable is used.

9. Connect the PC / laptop to the router / switch.

10. Connect the network camera to the router / switch.

11. Connect the power supply to the network camera.

12. If a DHCP server is available in your network, set the network interface of your PC / laptop to

“Obtain an IP address automatically”.

13. If no DHCP server is available, configure the network interface of your PC / laptop to 192.168.1.1

and the default gateway to 192.168.1.2.

14. Go to point 4.6 to finish the initial set-up and establish the connection to the network camera.

 CAT 5 Ethernet cable

Internet

82

English

4.6 Accessing the network camera for the first time

The network camera is accessed for the first time using the IP Installer.

After the installation wizard is started, it searches for all connected EyseoIP network cameras and video

servers in your network.

The program is found on the supplied CD-ROM. Install the program on your PC and then run it.

If a DHCP server is available in your network, the IP address is assigned automatically for both the PC /

laptop and the network camera.

If no DHCP server is available, the network camera determines a free IP address from the 192.168.1.2–

192.168.1.254 range independently. Your PC system must be located in the same IP segment in order to

establish communications with the network camera.

The standard setting for the network camera is “DHCP”. If no DHCP server is in operation in

your network, then we recommend setting the IP address manually to a fixed value following

initial access to the network camera.

83

English

4.7 Accessing the network camera over a web browser

When you first access the network camera under Windows, the web browser queries the installation of an

ActiveX plug-in for the network camera. This query depends on the Internet security settings of your PC. If the

highest security level is set, the PC will refuse any installation and any attempt at running it. This plug-in is

used for displaying the video in the browser. To continue, click “Install”. If the web browser prevents the

installation, open the Internet security settings and reduce the security level or consult your IT or network

administrator.

4.8 Installing the ActiveX plug-in

If Mozilla Firefox is used as the browser when accessing the camera, an MJPEG stream is

provided by the camera instead of the ActiveX plug-in.

4.9 Adjusting the security settings

84

English

Note: Your PC security settings may prevent a video stream. You can change the security

settings to a lower level under “Tools / Internet Options / Security”. Make sure you enable

ActiveX controls and downloads.

4.10 Password prompt

An administrator password is defined in the network camera as standard. However, the administrator should

define a new password immediately for security reasons. After the new administrator password is stored, the

network camera asks for the user name and password every time it is accessed.

The administrator account is set as follows (factory setting): User name = “admin”; password = “admin”. Each

time the network camera is accessed, the browser displays an authentication window and asks for the user

name and password. If you can no longer access your personal settings in the administrator account, you can

log in again with the “admin” user name / password after resetting the network camera to the factory settings.

To enter a user name and password, proceed as follows:

Open Internet Explorer and enter the IP address of the camera (e.g. “http://192.168.1.14”).

You are then prompted for authentication:

-> You are now connected with the network camera and can see a video stream.

4.11 Accessing the network camera over an RTSP player

You have the possibility of accessing the MPEG-4 / H.264 data streams on the network camera with an

RTSP-compatible media player. The following free media players support RTSP:

 VLC Media Player

 Real Player

 Quicktime Media Player

The address format for entering the connection data is as follows:

rtsp://<IP address of the network camera>:<RTSP port>/<Type of video data stream>

85

English

Example:

rtsp://192.168.1.14:554/video.mjpg (MJPEG stream)

rtsp://192.168.1.14:554/video.mp4 (MPEG-4 stream)

rtsp://192.168.1.14:554/video.h264 (H.264 stream)

4.12 Accessing the network camera over a mobile phone

Ensure that you can establish an Internet connection over your mobile phone. Your mobile phone must also

be equipped with an RTSP-compatible media player. The following media players for mobile phones support

RTSP:

 Real Player

 Core Player

Please note that access to the network camera via mobile phone is restricted due to the reduced network

bandwidth available. We therefore recommend making the following video stream settings in order to reduce

the data quantity:

Video compression MPEG-4

Resolution 160x120

Frame rate 5 frames / second

Video quality (constant bit rate) 48 kbps

If your media player does not support RTSP authentication, then deactivate the authentication mode for RTSP

in the network camera configuration settings.

The address format for entering the connection data is as follows:

rtsp://<IP address of the network camera>:<RTSP port>/<Type of video data stream>

Example:

rtsp://192.168.1.14:554/video.3gp

86

English

4.13 Accessing the network camera over ABUS VMS

The free ABUS VMS Express recording software can be found on the supplied CD-ROM. You then have the

possibility of connecting and recording several ABUS Security Center network cameras on one interface.

Further information can be found in the software manual on the enclosed CD-ROM.

87

English

5. User functions

Open the main menu on the network camera. The interface is divided into the following main areas:

Live image

You can access the full-screen view by double-clicking here (on Internet Explorer only).

Control the direction of the network camera by clicking the mouse once. Depending on the position of the

mouse cursor in the live image, the pan/tilt head of the network camera moves up, down, left or right (on

Internet Explorer only).

These functions are only available when using Internet Explorer.

Camera control

Setting

Used for configure the camera (administrator settings).

Client setting

Mode: Select the compression mode for image transmission in the live image.

Live image

Camera control

Audio / video control

Live image

88

English

View size: Select the window size.

Note: The view size specified here relates to the live image shown in the display mode of the

browser. The resolution set in the camera is always transmitted, even when the view size set

here is smaller.

Protocol: Allows a connection protocol to be selected between the client and the server. The following

protocol options are available for optimising the application: UDP, TCP, HTTP.

The UDP protocol gives you a larger number of audio and video streams in real time. However, some data

packets can be lost due to the large data volume in the network. Pictures may be unclear in this case. The

UDP protocol is recommended if you have no special requirements.

With the TCP protocol, fewer data packets are lost and the video display is more accurate. However, the

disadvantage of this protocol is that the video stream is transmitted at a lower frame rate than the UDP

protocol.

Use the HTTP protocol if the network is protected by a firewall and only the HTTP port (80) is available.

The selection of the protocol is recommended in the following order: UDP – TCP – HTTP.

This function is only available when using Internet Explorer.

Video buffer: Activate the video buffer if your connection only has a limited bandwidth. Image data is saved

temporarily in the network camera for clearer transmission, meaning the image delay is increased.

Image setup

Set the brightness, contrast, saturation and sharpness here.

This function is only available when using Internet Explorer.

89

English

PT control

Use the control buttons for pan/tilt control on the camera.

Arrows:

The pan/tilt head is moved by clicking the button

in the corresponding direction

Home:

The image is moved to the home position

Preset Go:

Select one of the preset positions from the list. The

network camera accesses the position immediately.

Set:

The current camera position in the live image is

saved as a preset. Presets saved in this way all have

a generic file name (Preset1, Preset2 etc.).

Patrol:

Select which tour should be started. Tours 1 to 4 can

be changed in the camera settings.

Go:

Starts the selected tour.

Pan speed:

Select a value between 0 and 100. Higher values

result in quicker movements.

Tilt speed:

Select a value between 0 and 100. Higher values

result in quicker movements.

Auto Pan speed:

This setting is used during a tour.

Select a value between 0 and 100. Higher values

result in quicker movements.

90

English

5.1 Audio / video control

These functions are only available when using Internet Explorer.

Snapshot

The web browser displays a new window containing the snapshot. To save the snapshot, either left-click it

and then click the floppy disk icon or right-click it and select “Save” from the context menu.

Full-screen

Activates the full-screen view. The live image on the network camera is shown on the entire screen.

Start / stop live image

The live stream can be stopped (paused) or exited. In both cases, the live stream can be continued by

pressing the Play symbol.

Local recording

A recording on the local hard disk can be started or stopped here. By clicking the button, the Windows “Save

as” dialog is called up.

Select a storage folder on your hard disk. A directory and recording file are created automatically in the folder

under the following name:

YYYYMMDD

YYYYMMDDHHmmss.avi

Y = Year

M = Month

D = Day

H = Hour

m = Minute

s = Second

91

English

Example:

C:\Recording\20091215\20091215143010.avi

The recorded data can be played back over an MP4-compatible video player (e.g. VLC Media

Player). Alternatively, you can also watch the videos on Windows Media Player by installing a

video codec in the IP Installer.

Microphone on

The microphone on your PC is active in order to send voice data to the network camera.

Microphone off

The microphone on the PC is deactivated. No voice data is transmitted.

Loudspeaker on

The loudspeakers on the PC are activated. Voice data from the network camera can be played back.

Loudspeaker off

The loudspeakers on the PC are deactivated. Voice data from the network camera cannot be played back.

Volume control

Used to set the volume of the audio playback.

Digital zoom

Click on the magnifying glass icon to activate the digital zoom. The zoom factor can be changed on the scroll

bar.

Setting the zoom factor

Change the zoom factor by moving the bar from left (low zoom) to right (high zoom).

Abus TVIP51500 User manual

Related papers

Other documents