ABSCO 15141RK User manual

Brand
ABSCO
Model
15141RK
Type
User manual
Absco Industries Assembly Instruction Manual
ABSCO REGENT SHED
MODEL: 15141RK
1.52mW x 1.44mD x 1.96mH
Model: 15141RK 14/09/18 1.1
1
Download the Absco
Sheds Assembly App
for instructional videos
MANU FA CT URED
IN A US TR ALIA
SNAPTiTE
Assemb ly
AU: 1800 029 701
N Z: 0800 466 444
[email protected]
www.abscosheds.com.au
C
ONC
RETE
SLAB
1620
1540
When laying concrete slab, ensure there
is a rebated edge 25mm deep around
the perimeter. This will help water egress
from the base of the shed.
For construction in non-cyclonic areas
Wind rating: N2 as per AS4055-2012.
If you require a higher wind rating please contact
us: [email protected] or 1800 029 701
ABSCO INDUSTRIES ASSEMBLY INSTRUCTION MANUAL SHED MODEL: 23151GK 21-11-2017
CONCRETE SLAB
2360mm
1620mm
FRONT: 2.26m
SIDE: 1.52m
HEIGHT: 1.95m
We thank you for choosing an Australian made
shed. For further assistance please visit our detailed
instructional video library at
Http://www.abscosheds.com.au/watch-videos
At ABSCO Industries we are always looking to be
number ONE, so please let us know what you think
of our instructions. Feedback makes us better.
[email protected]
CONCRETE
REBATED EDGE
BOTTOM CHANNEL
CONCRETE SLAB
75mm WIDE REBATE
100mm
WHEN LAYING YOUR CONCRETE
SLAB, ENSURE THERE IS A
REBATED EDGE 25mm DEEP
AROUND THE PERIMETER
THIS WILL HELP WATER EGRESS
FROM THE BASE OF THE SHED
Absco Industries
Premier Shed Model: 23151GK
PAGE 01
Absco Industries Assembly Instruction Manual
ABSCO REGENT SHED
MODEL: 15141RK
1.52mW x 1.44mD x 1.96mH
Model: 15141RK 14/09/18 1.1
2
GENERAL INSTRUCTIONS
• Before commencing any assembly, read through these instructions in detail to gain a thorough
understanding of assembly methods and associated details.
• Unpack the carton and carefully identify and check off all the parts against the parts described
and illustrated on "COMPONENTS PACKING LIST" pages.
SITE PREPARATION
• The site for the shed must be level. An uneven surface may result in misalignment of parts.
• The shed shall be erected on top of a reinforced concrete slab and anchored down appropriately
illustrated on “FINAL CONSTRUCTION” page.
TOOLS REQUIRED
SAFETY NOTES
• Some parts may have sharp edges. It is advisable to wear gloves when handling these items and
safety glasses if drilling holes. Sensible shoes are highly recommended.
• Do not erect your shed in windy conditions.
• Ensure that the shed is securely anchored to a solid foundation immediately after construction is
completed.
• It is highly recommended to erect the shed with two or more people.
RECOMMENDED
3mm drill bit
10mm drill bits
metal & masonry
Absco Industries Assembly Instruction Manual
ABSCO REGENT SHED
MODEL: 15141RK
1.52mW x 1.44mD x 1.96mH
Model: 15141RK 14/09/18 1.1
3
COMPONENT PACKING LIST
Check off all components.
COMPONENT
DESCRIPTION
PART
No.
CHECK
COMPONENT
DESCRIPTION
PART
No.
CHECK
QTY QTY
2
2
1
3
1
2
2
2
2
1785mm X 773mm
30A
STEEL SHEET
STEEL SHEET
1785mm X 731mm
32A
STEEL SHEET
1725mm X 773mm
B
81I
CHANNEL
L = 1439
59C
CHANNEL
L = 1439
STEEL SHEET
795mm X 773mm
50L
2
STEEL SHEET
795mm X 773mm
50R
2
GABLE L/H
L=735mm
18L
2
GABLE R/H
L=735mm
18R
1
75A
CHANNEL
L = 1513mm
53B
CHANNEL
L = 1513mm
1
75C
CHANNEL
L = 1513mm
1
CHANNEL
L = 1513mm
81E
78C
CHANNEL
L = 1513
97C
RIDGE
BEAM
L = 1513
STEEL SHEET
1785mm X 731mm
33A
1
STEEL SHEET
1785mm X 711mm
34A
1
CHANNEL
L = 1513mm
81F
1
79C
CHANNEL
L = 783mm
1
CHANNEL
L = 1785
80A
1
Absco Industries Assembly Instruction Manual
ABSCO REGENT SHED
MODEL: 15141RK
1.52mW x 1.44mD x 1.96mH
Model: 15141RK 14/09/18 1.1
4
COMPONENT PACKING LIST
4
12A
1
DOOR
STRAP
L: 165mm
14A
2
CAP GABLE
L: 170mm
COMPONENT
DESCRIPTION
PART
No.
CHECK
COMPONENT
DESCRIPTION
PART
No.
CHECK
QTY QTY
INSTRUCTIONS & FITTINGS PACKET
2
11
1
2
58A
CHANNEL WITH HINGES
L = 1725mm
58B
CHANNEL
L = 1725mm
58C
CHANNEL
L = 773mm
89A
JAMB L= 1785mm
91A
JAMB L= 1120mm
90C
JAMB L= 783mm
1
89B
JAMB L= 1785mm
1
85B
LIP TRIM L= 795mm
SELF TAPPING
SCREWS
(20mm)
6
DOOR
PADBOLT
HASP
1
1
SELF TAPPING SCREWS
PACKET CONTAINING 220
1
DOOR
PADBOLT
FAST006
3/16 COUNTERSUNK
SCREWS & NUTS
6
3.2 x 8mm
BLIND POP RIVETS
6
PSTKSGL - SINGLE DOOR FITTINGS PACK
PACK 6P - SCREW PACK 6
PACK 6P
SCREW PACK 6
1
PHILLIPS DRIVER BIT
3mm DRILL BIT
DRILL
FAST007
FAST038
1 1
1
1
SELF TAPPING SCREWS
PACKET CONTAINING 100
PSTKSGL
SINGLE DOOR FITTINGS PACK
Absco Industries Assembly Instruction Manual
ABSCO REGENT SHED
MODEL: 15141RK
1.52mW x 1.44mD x 1.96mH
Model: 15141RK 14/09/18 1.1
5
SNAPTiTE ASSEMBLY GUIDE
The Snaptite Assembly System locks end channels to all roof and wall sheets without the need for
tools and fasteners.
To assemble each panel, the perimeter channels are secured to the top and bottom of each panel.
Gently tap the channel over the SNAPTiTE lugs on the sheet, working along the sheet.
Each perimeter channel must fi nish fl ush with the edges of the sheets. Simply tap the channel along
the sheets until each end is neatly fl ush. If you need to remove channels from the panels, slide it off
from the side.
Channel locks the shed panel into
position without the need for screws!
FASTENING SYMBOLS
Secure channel to sheeting by SNAPTiTE
fastening method.
Join components together with one
screw at this location only, as some
channels have extra holes that are not
required for this model of shed.
Do not join components together at
this location yet, as the screws may
obstruct further assembly of the other
components.
Join components together by pre-drill-
ing the holes fi rst. Use one component as
template to mark where the holes are and
drill with a 3mm drill bit.
3mm pop rivet
4mm nut and bolt set.
D
SNAP
T TE
i
Absco Industries Assembly Instruction Manual
ABSCO REGENT SHED
MODEL: 15141RK
1.52mW x 1.44mD x 1.96mH
Model: 15141RK 14/09/18 1.1
6
OVERVIEW OF ROOF COMPONENTS
OVERVIEW OF ROOF COMPONENTS
50L
50L
50R
50R
85B
14A
85B
97C
78C
81E
85B
85B
81E
Absco Industries Assembly Instruction Manual
ABSCO REGENT SHED
MODEL: 15141RK
1.52mW x 1.44mD x 1.96mH
Model: 15141RK 14/09/18 1.1
7
OVERVIEW OF WALL COMPONENTS
OVERVIEW OF WALL COMPONENTS
33A
32A
30A
30A
32A
32A
34A
B
53B
79C
89B
89A
81I
90C
80A
81I
81F
59C
18L
75A
18R
18L
18R
59C
22A
91A
75C
Absco Industries Assembly Instruction Manual
ABSCO REGENT SHED
MODEL: 15141RK
1.52mW x 1.44mD x 1.96mH
Model: 15141RK 14/09/18 1.1
8
REAR PANEL ASSEMBLY
1x required.
30A
30A
75C
81F
SNAP
T TE
i
SNAP
T
TE
i
Absco Industries Assembly Instruction Manual
ABSCO REGENT SHED
MODEL: 15141RK
1.52mW x 1.44mD x 1.96mH
Model: 15141RK 14/09/18 1.1
9
ROOF PANEL ASSEMBLY
2x required.
Fit 81E to edge
of sheet with pre-
punched holes.
50L
50R
SNAP
T TE
i
78C
85B
81E
85B
SNAP
T TE
i
Absco Industries Assembly Instruction Manual
ABSCO REGENT SHED
MODEL: 15141RK
1.52mW x 1.44mD x 1.96mH
Model: 15141RK 14/09/18 1.1
10
RIGHT SIDE PANEL ASSEMBLY
1x required.
Small pan
32A
32A
SNAP
T TE
i
SNAP
T TE
i
59C
81I
Absco Industries Assembly Instruction Manual
ABSCO REGENT SHED
MODEL: 15141RK
1.52mW x 1.44mD x 1.96mH
Model: 15141RK 14/09/18 1.1
11
LEFT SIDE PANEL ASSEMBLY
1x required.
SNAP
T TE
i
SNAP
T TE
i
59C
81I
32A
33A
80A
Small pan
Absco Industries Assembly Instruction Manual
ABSCO REGENT SHED
MODEL: 15141RK
1.52mW x 1.44mD x 1.96mH
Model: 15141RK 14/09/18 1.1
12
FRONT PANEL ASSEMBLY
1x required.
SNAP
T TE
i
SNAP
T TE
i
34A
89A
53B
75A
79C
89B
90C
Absco Industries Assembly Instruction Manual
ABSCO REGENT SHED
MODEL: 15141RK
1.52mW x 1.44mD x 1.96mH
Model: 15141RK 14/09/18 1.1
13
DOOR PANEL ASSEMBLY
DOOR PANEL ASSEMBLY
Vertical door channels are
installed in the opposite
orientation compared to the
horizontal door channels.
Short fl ange
of channel
Long
fl ange of
channel
SINGLE DOOR
58C
58C
S
N
A
P
T
TE
i
S
N
A
P
T TE
i
12A
B
B
58B
58A
D
D
D
D
1x required.
Absco Industries Assembly Instruction Manual
ABSCO REGENT SHED
MODEL: 15141RK
1.52mW x 1.44mD x 1.96mH
Model: 15141RK 14/09/18 1.1
14
SINGLE DOOR PANEL
NOTE: Nuts and bolts are also
supplied and may be used instead of
rivets. Use a 4mm drill bit to enlarge
these holes in the jamb
NOTE: The holes to fasten the padbolt hasp are not
pre-punched to allow for proper alignment. Position
the hasp centrally over the padbolt shaft and drill 3mm
holes and secure with screws.
91A
91A
DOOR PANEL ASSEMBLY
B
Absco Industries Assembly Instruction Manual
ABSCO REGENT SHED
MODEL: 15141RK
1.52mW x 1.44mD x 1.96mH
Model: 15141RK 14/09/18 1.1
15
PANEL CONSTRUCTION
NOTE: Take care
to ensure that all
wall panels are not
upside down. The
top channels of each
panel are pre-punched
for attaching roof
sheeting. The base
channels are not pre-
punched.
Pre-punched
channel to
match ridge
beam holes
Side wall channels
fit into the
notched rear wall
channels.
Pre-punched holes in roof panel to this side
for connection to front and rear walls.
Orient panel so
channel (78C)
goes into ridge
beam
Channel (81E)
this end
97C
33A
80A
89B
CONNECT DOOR MULLION SECTIONS WITH SIX
20mm SCREWS
REPLACE PADBOLT HASP 10mm
SCREWS WITH 20MM SCREWS
D
D
D
D
D
D
D
D
D
D
D
D
D
Absco Industries Assembly Instruction Manual
ABSCO REGENT SHED
MODEL: 15141RK
1.52mW x 1.44mD x 1.96mH
Model: 15141RK 14/09/18 1.1
16
INSIDE VIEW OF FIXINGOUTSIDE VIEW
37mm
ROOR OVERHANGS
ALL WALL PANELS
BY 37mm
Secure ridge beam to
gable sections with
two screws at each
end. Secure each roof
panel with one screw
in each corner only at
this stage
Absco Industries Assembly Instruction Manual
ABSCO REGENT SHED
MODEL: 15141RK
1.52mW x 1.44mD x 1.96mH
Model: 15141RK 14/09/18 1.1
17
FINAL CONSTRUCTION
Each anchor consists of one nut, bolt, M10
dynabolt and steel angle.
Drill a 10mm hole into the wall sheet.
Drill a 10mm hole into the concrete.
Bolt and Nut*
M10 4.6/S
Steel Angle*
35 x 35 x 3
M10 Dynabolt*
* Denotes hot dip galvanised fi nish
Wall Sheet
Slab
14A
Bend the top and bottom
flanges as shown, then hook the
bottom flanges under the top
channel and screw top to the
ridge beam with two screws.
ANCHORING OF SHED
50
700
Location of 8
concrete
anchors
50
50
50
700
700
700
700
D
D
D
D
D
D
D
D
D
D
D
D
Absco Industries Assembly Instruction Manual
ABSCO REGENT SHED
MODEL: 15141RK
1.52mW x 1.44mD x 1.96mH
Model: 15141RK 14/09/18 1.1
18
Absco Gable Roof Shed Notes
• 1.G This instruction manual shall be read in conjunction with other consultants drawings, specifi cations and
written instructions provided by Absco and/or their representatives.
• 2.G The drawings provided herein are for installation and structural engineering purposes only.
• If discrepancies are discovered within the documentation provided, these shall be brought to the attention
of Absco and written approvals obtained prior to commencing the affected section of work.
• 3.G If in doubt ask.
• 4.G Until approvals from the local authorities are obtained, commencement of construction from these
drawings shall not commence.
• 5.G Unless varied by the project specifi cation, all materials and workmanship shall be undertaken in
accordance with the relevant Australian standards and the by-laws and ordinances of the relevant building
authorities.
• 6.G All dimensions indicated in these drawings shall be verifi ed on site by the installation contractor. Scaling
of drawings shall not be undertaken.
• 7.G Prior to commencing works on site, the contractor shall verify the position of all services in the area to
ensure that the construction does not interfere with any of those services.
• 8.G During installation on site the shed structures shall be maintained in a stable condition with no part
becoming overstressed or permanently deformed.
• 9.G In circumstances where the shed has been installed in a manner which is inconsistent with the installation
manual, structural certifi cation shall be void.
• 10.G The structural components detailed within this installation manual have been designed for the following
loads in accordance with AS/NZS1170 based on a Class 10a, Type 2 structure:
• Roof Live Load: 0.25 kPa uniformly distributed or 1.1 kN concentrated as per AS/NZS1170.1
• Wind Load: Classifi cation N2, Non-Cyclonic to AS4055 where Vu = 40 m/s, Vs = 26 m/s
Windward wall Cpe = 0.7
Leeward Wall Cp,e = -0.3 to -0.5 as applicable based on shed geometry
Side Wall Cp,e = -0.5 to -0.65 as applicable based on shed geometry
Roof Cp,e = -0.5 to -1.3 depending on wind direction
6-12 Activity St, Acacia Ridge QLD 4110
PO Box 119, Acacia Ridge QLD 4110
AU: 1800 029 701
N Z: 0800 466 444
[email protected]
www.abscosheds.com.au
General
Absco Industries Assembly Instruction Manual
ABSCO REGENT SHED
MODEL: 15141RK
1.52mW x 1.44mD x 1.96mH
Model: 15141RK 14/09/18 1.1
19
Absco Gable Roof Shed Notes
• 1.S All structural steelwork shall have a corrosion protection system applied consistent with AS/NZS 2312-
2002.
• 2.S All structural steelwork detailed within this installation manual shall be minimum Grade
• 550 for roll formed sections (including roof and wall sheeting) and Grade 250 for angle sections.
• 3.S All roof, and wall sheeting shall be minimum base metal thickness of 0.3mm
• 4.S All snaptite channels and jambs shall be minimum base metal thickness of 0.42mm
• 5.S All top hats shall be minimum base metal thickness of 1.0mm
• 6.S All screw fasteners shall be Phil Pan Head Zinc Plated #8 x 3/4” (STP0820)
• 7.S All bolt fasteners for anchoring shall be M10 minimum grade 4.6/S
• 8.S Installation of screw fasteners shall generally be undertaken in accordance with the relevant provisions
of AS1562.
Steelwork
• 1.F The supporting slab foundation for the garden shed shall be of a minimum size indicated on the installation
manual. The top surface of the formed slab shall be level and free of any irregularities which would inhibit
the installation of the shed.
• 2.F The structural engineering design for the supporting slab foundation shall be undertaken by a suitably
qualifi ed structural engineer. The design shall consider all relevent provision of AS3600 and AS2870.
• 3.F Between adjacent footings or excavations, the contractor installing the slab foundation shall not exceed
a rise of 1 in a run of 2 in line of slope.
• 4.F Unless approved in writing by the slab foundation engineer, the limits of excavations near existing
footings shall be in accordance with that indicated below.
Supporting Slab and Foundations
The contactor shall undertake investigatory
localised excavations near existing
footings to ascertain their depth prior to
excavating adjacent to them. It is noted that
excavating to a depth below that indicated
above shall not be undertaken without
the written approval from the engineer.
Absco Industries Assembly Instruction Manual
ABSCO REGENT SHED
MODEL: 15141RK
1.52mW x 1.44mD x 1.96mH
Model: 15141RK 14/09/18 1.1
20
Absco Sheds Storage Guidelines
• Absco Sheds are designed to be weatherproof for normal weather conditions. In the event of extreme
weather conditions such as heavy rain, combined with high wind gusts, the ridge capping, sheeting joins,
screw fi xings etc., may exhibit minor deformations which may allow some water entry. These areas should be
checked regularly to ensure that maximum strength and protection is maintained.
• Other weather conditions such as extreme heat and extreme cold, moist or dry air can infl uence the effects
of concrete fl oor moisture and/or condensation on the underside of the roof sheets.
• Absco Sheds and storage units are primarily used for storage of garden equipment such as lawnmowers,
wheelbarrows, garden tools etc. Storage items that might be adversely affected by any of the above conditions
may require additional protection such as being sealed or covered by plastic sheets and/or stacked above
the concrete fl oor on timber slats.
• Waterproof sealants may be used to offer further protection where required around joins and screw fi xings,
as can rubber door seals and other products which are available from most hardware outlets.
• Placement of waterproof sealants (silicone) between the base of the shed and concrete slab is not
recommended, as this process can have a reverse effect, preventing excess water from escaping, resulting
with water accumulating and being trapped inside the shed.
• Absco accepts no responsibility for water entry, fl oor moisture, condensation or the condition of the Contents
inside your Absco steel building arising from any of the pre-mentioned weather conditions.
6-12 Activity St, Acacia Ridge QLD 4110
PO Box 119, Acacia Ridge QLD 4110
AU: 1800 029 701
N Z: 0800 466 444
[email protected]
www.abscosheds.com.au
Page is loading ...
Page is loading ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22

ABSCO 15141RK User manual

Brand
ABSCO
Model
15141RK
Type
User manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents