WamBam Fence BL19102 Installation guide

Type
Installation guide

WamBam Fence BL19102 is a vinyl picket gate designed for easy integration with the Nantucket Vinyl Picket Fence, standing 4 feet high. It can also be used in openings up to 50 inches wide by adjusting the top and bottom rails. The gate features stainless steel hardware for durability and includes gate caps, T-brackets, a gate latch, top and bottom rails, vertical stiles, pickets, gate bottom brackets, and stainless steel screws. It allows for a custom fit and is recommended to be installed with gate posts for optimal performance and longevity.

WamBam Fence BL19102 is a vinyl picket gate designed for easy integration with the Nantucket Vinyl Picket Fence, standing 4 feet high. It can also be used in openings up to 50 inches wide by adjusting the top and bottom rails. The gate features stainless steel hardware for durability and includes gate caps, T-brackets, a gate latch, top and bottom rails, vertical stiles, pickets, gate bottom brackets, and stainless steel screws. It allows for a custom fit and is recommended to be installed with gate posts for optimal performance and longevity.

REALLY
Important stuff to know about
installing your WamBam gate.
WamBam Nantucket Vinyl Picket
Gate w/Stainless Steel Hardware
(48 H x 48W)
1-877-778-5733
w ww.wambamfence.com
V-2.0
This gate is designed to be integrated with our
WamBam Nantucket Vinyl Picket Fence - 4' High.
(This gate can also be used in any opening that is 50” wide or less
by trimming down both the top and bottom rail).
(Adjustable Width)
1
1 - Read Over Fence Instructions First
Your gate and fence will work better together as an
integrated
solution if you rst take the time to read and understand your
fence instructions.
2 -
Pre-Assemble the Gate Frame
(without pickets)
Please do not screw your gate frame together until you have rst
temporarily assembled the gate. In other words, do a dry run rst.
This will ensure three things:
a) That you have everything necessary to complete the gate.
b) That you will have assembled the gate in the correct order.
c) All the pieces t and function properly.
Its easier to trouble shoot when things are not screwed together.
After you assemble your gate correctly, please disassemble as
necessary and use screws to permanently assemble the gate.
3 -
Ideally, Install Your Gate Posts
Before Your Fence Posts
Your fence panels will be more forgiving for a custom
t than your gate. Ideally, position and install your
gate posts before you do anything else, or very early
on in the process of setting up your fence run.
Install Your Gate Posts
Before Installing Your
Fence Posts.
For more information, contact us at 1 877-778-5733.
4 -
Ideally, Do Not Hang Your Gate System
Off a Single Non-Supported Post
Your gate will perform better and last longer if your hinge post is connected to a panel of fence which is
connected to another post. The weight strain will be transferred unto two posts versus just one. Installing
fence panels on both sides of your gate is the ideal in all situations. If this is not possible because of space
restrictions, please contact us for alternative solutions to overcome.
Do Not Hang Gate on Lone Soldier Post.
WamBam Nantucket Vinyl Picket Gate
w/Stainless Steel Hardware
PRODUCT OVERVIEW
For more information, contact us at 1 877-778-5733.
2
Gate InstallationGate Assembly
48 in
3.5 in
3.78 in
1.5 in
7.75 in
24.875 in
4 in
3.5 in
47.5 in
1
.5in.
3.5in.
3.5in.
1
.5in.
B
A B
C D
3.5in.
1
.5in.
.090in. wall thickness
C
1
.5in.
D
3.5in.
A
Posts & Pipe Anchors
Sold Separately
Ground
50 in
54 in
2 in
32.5 in
26 in
48 in
49.375 in
48 in
Post & Pipe Anchor
Sold Separately as 1-Pack
BOX CONTENTS
Each Gate Box Includes:
• Gate Caps (2)
• T-Brackets (2)
• Gate Latch (1)
• Top Rail (1)
• Gate Hinges (2)
• Vertical Stiles (2)
• Pickets ( 7)
• Gate Bottom Brackets (2)
• Bottom Rail (1)
• Stainless Steel Screws (20)
Sold Separately:
• 4ft. Post & Pipe Anchor (1-Pack)
.135in. wall thickness
WamBam Nantucket Vinyl Picket Gate
w/Stainless Steel Hardware
3
DETAILED ASSEMBY INSTRUCTIONS
C - Insert vertical gate stiles. They will
BOTTOM OUT against bottom horizontal rail
C
A
IMPORTANT!
Insert fully to this point.
Insert fully to this point.
Completely assembled
gate shown
Assemble the Gate Frame Bottom & Sides
STEP 1
B - Insert the bottom rail ALL THE WAY until it
BOTTOMS OUT INSIDE GATE BRACKET
A - Insert the bottom rail ALL THE WAY until it BOTTOMS OUT inside
gate bracket
Fasten gate brackets to internal members
though inside of frame using screws.
Did you do a dry run of assembly first?
Please read page 1 of instructions.
Note that the bottom rail
is ribbed internally.
B -
Insert rail ALL THE WAY until it
BOTTOMS OUT inside bracket
B
A - Insert top rail ALL THE WAY until it
BOTTOMS OUT inside bracket
A
Assemble the Gate Frame Top & Attach to Sides
STEP 2
B
IMPORTANT!
IMPORTANT!
WamBam Nantucket Vinyl Picket Gate
w/Stainless Steel Hardware
4
C - Slide T-brackets with toprail attached down
over the vertical gate stiles
D - Completely assembled gate frame shown
C D
A
Screw Gate Frame/Brackets
STEP 3
A - Screw into brackets as necessary
For more information, contact us at 1 877-778-5733.
WamBam Nantucket Vinyl Picket Gate
w/Stainless Steel Hardware
WARNING: Pickets once inserted into
bottom rail cannot be removed.
5
A - Insert pickets through top rail
down into bottom rail
A
A
Fasten Gate Hinges & Gate Latch
STEP 5
Insert Pickets Into Gate Frame & Attach Caps
STEP 4
B C
B -
Install bracket caps. Use pvc
glue (purchase separately) if you
would like to permanently secure
caps to T-brackets
C - Completed gate with frame
shown.
A - Fasten gate hinges and gate latch onto the gate brackets with screws.
For more information, contact us at 1 877-778-5733.
WamBam Nantucket Vinyl Picket Gate
w/Stainless Steel Hardware
B
Level Gate & Adjust Hinges
STEP 7
B - Fasten hinges to post with screws
6
Position, Adjust & Algn Gate/Secure Hinges to Posts
STEP 6
For more information, contact us at 1 877-778-5733.
LEVEL
A
A - Fasten gate hinges accordingly
B -
Check for level, fit and function to latching post
B
A - Use temporary spacers OR
blocks to rest the gate on during
alignment and installation
WamBam Nantucket Vinyl Picket Gate
w/Stainless Steel Hardware
Align & Install Latch
7
For more information, contact us at 1 877-778-5733.
Adjust the spring tension
in gates as necessary.
.
Use steel insert pin.
C D
C -
Hinges can be adjusted moderately
to bring gate into level alignment
with post
Latch is designed for left and right hand applications Temporarily remove.
the spring, bolt and reverse paddle portion as necessary.
B
Congratulations! You did it!
Go grab a beverage of your choice, admire your
handy work, and show us what you got by entering
our annual photo/video contests!
STEP 8
A
A - Align and fasten the gate latch catch to fit
and function with the gate finger.
WamBam Nantucket Vinyl Picket Gate
w/Stainless Steel Hardware
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

WamBam Fence BL19102 Installation guide

Type
Installation guide

WamBam Fence BL19102 is a vinyl picket gate designed for easy integration with the Nantucket Vinyl Picket Fence, standing 4 feet high. It can also be used in openings up to 50 inches wide by adjusting the top and bottom rails. The gate features stainless steel hardware for durability and includes gate caps, T-brackets, a gate latch, top and bottom rails, vertical stiles, pickets, gate bottom brackets, and stainless steel screws. It allows for a custom fit and is recommended to be installed with gate posts for optimal performance and longevity.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI