Cetacea ASTRO-XLR001-SFC User manual

Brand: Cetacea

Model: ASTRO-XLR001-SFC

Category: Interactive whiteboards

Type: User manual

This manual is also suitable for

Technical Audio for the 21st Century Classroom

Owner's Manual

Astronaut XL

A GETTING STARTED 2–5

Important—Read First 2

Shipping Kit Contents 3

Astronaut Up Close 4

Safety Precautions 5

B INSTALLATION 6–17

Installer Notes 6

Cabling Options 7

Ceiling Mount Instructions 8–13

Source Connections 14–15

Power Connection 16–17

C TECHNICAL SUPPORT 18–20

Troubleshooting Guide 18–19

Contact Info 20

D LIMITED WARRANTY 21

Index

Online ResourcesContact Info

CETACEA SOUND CORP

2003 East Center Circle

Plymouth, Minnesota 55441

SALES

[email protected]

CUSTOMER SERVICE

[email protected]

PHONE

(763) 559-1019

U.S.A. and Canada

(800) 556-1922

FAX

(763) 559-1585

ONLINE

www.cetaceasound.com

OWNER'S MANUAL

For use with the following Astronaut XL systems.

System No.: ASTRO-XLW001 | ASTRO-XLD001 | ASTRO-XLR001

NEWS CENTER

Announcements

& Events

EMAIL / RSS

News Delivered

Your Way

SUPPORT

Documentation

& Resources

PLEASE READ ALL INSTRUCTIONS CAREFULLY AND KEEP A COPY OF THIS GUIDE IN A SAFE PLACE

Getting Started

Astronaut branded speaker systems are ampliﬁ ed and designed

to plug into either mono or stereo sources of sound. Please check

the model number of your speaker for input speciﬁ cations.

Common Sources

Projector

Microphone

DVD / VHS

Interactive Whiteboard

CD / iPod® / iPad®

Computer

The Astronaut has a built-in ampliﬁ er. Connect to ﬁ xed or

variable line level sources only.

When using an electronic source, turn off all equalizer or

compression algorithm effects, commonly called “bass boost”,

“surround sound”, “jazz”, etc. If connecting to a computer,

make sure that the sound card software is properly set up

for uncompressed and un-boosted stereo output. Use only

the stereo output from DVD’s and personal computers. The

Astronaut is not designed to plug into third party ampliﬁ ers,

pre-amps, or subwoofer output jacks. Most line and variable

headphone jacks are suitable sources.

Turn OFF special effects

IMPORTANT—READ FIRST A

The Astronaut is an ampliﬁ ed speaker

iPod® and iPad® are registered trademarks of Apple Inc.

Astronaut XL Speaker

S/N: ASTRO-XLD001

Desktop PS

S/N: ASTRO-XLR001

Wall Mount PS

w/ 30' Ext. Cable

S/N: ASTRO-XLW001

Wall Mount PS

Mounting Bracket

Ceiling Mount Kit

Aluminum Bolts (4)Ceiling Plate

Eye Bolt

Power Supply

1 of the following 3 power supply (PS) packages is included with your

system. Refer to the original order documentation for system number (S/N).

Please check that you have all of the following

items. If any items are missing, please contact

Cetacea Sound directly at (800) 556-1922.

PLEASE SAVE THE BOXES IN CASE YOU NEED TO RETURN YOUR PRODUCT FOR ANY REASON

Getting Started

SHIPPING KIT CONTENTS

PLEASE READ ALL INSTRUCTIONS CAREFULLY AND KEEP A COPY OF THIS GUIDE IN A SAFE PLACE

B – LINE INPUT

Stereo/mono, 3.5 mm mini-jack

ON / OFF LED

Green when on

REMOVE

Twist right to install /

left to uninstall

A – LINE INPUT

Stereo/mono, 3.5 mm mini-jack

C – LINE INPUT

Stereo/mono, 3.5 mm mini-jack

DC POWER

External power supply connector

Getting Started

ASTRONAUT UP CLOSE A

Getting Started

SAFETY PRECAUTIONS

Safeguard this equipment from high humidity conditions.

Read the instructions completely prior to attaching the

speaker overhead.

Take special care to not drop the equipment while

mounting to the ceiling.

Heed to all cautions and warnings posted within this guide

and on the speaker equipment.

When not using the equipment for long periods of time,

e.g. one month or longer, disconnect the power supply. The

Astronaut has over-voltage and diode protection built in;

however, it is best to err on the side of caution.

Never force anything into the openings or source inputs of

the speaker equipment.

Do not use this equipment if it shows obvious signs of

damage from shipping or dropping.

Do not use this equipment if ambient temperatures exceed

120 °F (48 °C).

Make sure equipment is properly mounted according to the

Ceiling Mount Instructions found in this guide. This is the

only approved method of installation; any other may cause

a loss in warranty.

Follow these instructions & use precautions

NOTE

All literature can be found on our website. Please download

an electronic copy of this guide for your records.

PLEASE READ ALL INSTRUCTIONS CAREFULLY AND KEEP A COPY OF THIS GUIDE IN A SAFE PLACE

Installation

INSTALLER NOTES B

Stereo Sources

Maximum input voltage should not exceed 300 mV per input

channel (A, B, or C). Do not use any multi-channel sources like

3-channel, Dolby Digital 5-channel, THX, or Q-Sound.

Mono Sources

Maximum input voltage should not exceed 150 mV per input

channel (A, B, or C). Use microphones that offer a mono or stereo

line output instead of microphone level output. Cetacea Sound

microphones are compatible with the Astronaut. Use of other

brands may result in unpredictable results and is not advised.

Line Level Sources

Although preamps, projector outputs, and music mixers are

popular, it is possible to “overdrive” the Astronaut with these

devices, leading to premature failure and a loss of warranty

coverage.

Additionally, equalizers, bass boost, surround sound, QSound,

spatializer, and other compression techniques are not necessary

and will add nothing to the sound quality. This can also

“overdrive” the Astronaut, leading to failure and a loss of

warranty coverage.

Recommended assembly tools

The following tools are recommended to mount the Astronaut

to a suspended ceiling tile.

Phillips head screwdriver

Hand drill with ¼" and ½" bits

Measuring tape

Input source speciﬁ cations

Cetacea Sound offers a variety of source and power cabling options to best support

your speciﬁ c installation project. Please ensure that all source and power cables are

procured prior to installation. Please visit our website for ordering information.

AC Extension Cables

Lengths: 6' | 10' | 20' | 30'

DC Extension Cables

Lengths (non-plenum): 6' | 10' | 20' | 40'

Lengths (plenum): 20' | 40'

Installation

CABLING OPTIONS

Power Extension Cables

Mono Cables, M-M

Length: 6'

Stereo Cables, M-M

Lengths: 3' | 20'

Source Cables

RCA to 3.5 mm, M-F

Length: 6'

In-line Volume Control, M-F

RCA Adapter

Volume Control

PLEASE READ ALL INSTRUCTIONS CAREFULLY AND KEEP A COPY OF THIS GUIDE IN A SAFE PLACE

Installation

CEILING MOUNT INSTRUCTIONS B

Determine Speaker Location

The Astronaut is very forgiving and does not need to be in the

center of the room for the best sound quality. Typically, installers

choose a location near the projector in order to share the same

power source in the ceiling. Try to maintain at least 4' of space

from the nearest wall or vertical obstruction.

CAUTION

Install speaker away from direct heat, high humidity, and

physical obstructions.

Do not install the Astronaut speaker near a projector

exhaust port or fan. The hot air from the projector can

cause the Astronaut to overheat and fail.

STEP 1

Mounting Bracket

Ceiling Mount Kit

Aluminum Bolts (4)

Ceiling Plate

Eye Bolt

Installation

CEILING MOUNT INSTRUCTIONS

Tap Holes Into Ceiling Tile

Remove a ceiling tile and set it on a ﬁ rm surface. Use the ceiling

plate as a guide to mark all 5 holes at locations A and B.

Drill or tap ¼" holes at location A for the provided 4 aluminum

bolts. Drill or tap a ½" hole at location B in the ceiling surface

for the security eye bolt.

Above Ceiling Cabling (optional)

If cables will be routed above the ceiling, cut a 1" hole into the

ceiling tile approximately 6" away from where the front of the

speaker will be.

Diagrams

6 in.

STEP 2

PLEASE READ ALL INSTRUCTIONS CAREFULLY AND KEEP A COPY OF THIS GUIDE IN A SAFE PLACE

Installation

CEILING MOUNT INSTRUCTIONS B

Mount Ceiling Plate and Bracket

Using the provided 4 aluminum bolts, fasten the ceiling plate C

to the top of the ceiling tile and ceiling bracket D to the bottom

of the ceiling tile. The bolts should be secured snugly; do not

over-tighten.

For Solid Ceiling Surfaces Only (optional)

The Astronaut also installs to hard surface ceilings. In this case,

Ceiling Plate C and the security eyebolt are not needed. Prior to

installing the Ceiling Bracket D, clip off the small teeth from the

ceiling side of the bracket using a pair of diagonal pliers. Fasten

Ceiling Bracket D using the appropriate screws for the ceiling

surface material, like wood or plaster screws.

Diagrams

STEP 3

Teeth

Installation

Mount Astronaut Speaker

a. Mount the Astronaut speaker to the ceiling bracket. Use a

ﬁ nger to locate the ﬁ rst peg E. Align this peg with one of

the four holes F on the speaker base. All other pegs will fall

into place accordingly.

b. Twist the speaker slightly to the right until you hear it lock.

Once locked, the ceiling bracket pointer G will line up with

the line-guide on the speaker lens.

CEILING MOUNT INSTRUCTIONS

REMOVE

NOTE

Make sure all 4 pegs are aligned and the speaker is ﬂ ush to

the ceiling prior to the step below.

HINT

It only takes light pressure to lock the speaker—no more

than it would to click a pen.

Diagrams

STEP 4

PLEASE READ ALL INSTRUCTIONS CAREFULLY AND KEEP A COPY OF THIS GUIDE IN A SAFE PLACE

Installation

CEILING MOUNT INSTRUCTIONS B

Lock Astronaut Speaker with Security Eye Bolt

Once the speaker is attached to the ceiling bracket, screw the

eyebolt H through the top of the ceiling plate I and into the

Astronaut base.

Diagram

STEP 5

NOTE

The eye bolt prevents the Astronaut from being removed

from below the false ceiling without ﬁ rst unscrewing it.

Installation

Secure Astronaut to Ceiling Truss (optional)

If desired, use a suspension wire (not supplied) to attach the eye

bolt to the ceiling truss.

CEILING MOUNT INSTRUCTIONS

Diagram

STEP 6

Suspension Wire

Ceiling Structure

False Ceiling

Ceiling Truss

PLEASE READ ALL INSTRUCTIONS CAREFULLY AND KEEP A COPY OF THIS GUIDE IN A SAFE PLACE

Installation

SOURCE CONNECTIONS B

The Astronaut can be hooked up to a variety of different A/V

devices. Please use high quality stereo/mono cables (3.5 mm

mini jacks) when connecting your source equipment. The

Astronaut has a built-in 3-channel mixer that accepts up to 3

simultaneous devices (A, B, C).

Connect A/V equipment to the Astronaut

Stereo/Mono Cable

Common Sources

Projector Microphone

DVD / VHS Interactive Whiteboard

CD / iPod® / iPad® Computer

Volume Control

When using a variable output, e.g., projector audio output,

control the volume level at the source. When using a ﬁ xed

audio output, an in-line volume control or mixer must be used

to adjust the volume (sold separately).

In-line Volume Control

Installation

SOURCE CONNECTIONS

Fixed Output | VCR/DVD Connections

Variable Output | Projector Connections

Connection diagrams

Stereo Cable*RCA Adapter*

Astronaut

DVD / VCR

In-line Volume

Control or other

attenuators*

Input A,B, or C

AUDIO

Stereo Cable*

Projector

Input A, B or C

Astronaut

Audio-Out

* Source cables sold separately.

PLEASE READ ALL INSTRUCTIONS CAREFULLY AND KEEP A COPY OF THIS GUIDE IN A SAFE PLACE

Installation

POWER CONNECTION B

High Voltage Connection

Wall Mount Power Supply

Choose this power supply when the AC outlet is near the

mounting location. Typically, the power source is shared with

and located near a projector.

Desktop Power Supply

Choose this power supply when the AC outlet location requires

AC power extension cables or international plugs.

Wall Mount PS Desktop PS

STEP 1

NOTE

We offer optional length power cords for long-run

applications and other custom installations. (See pg. 7)

CAUTION

Do not connect speaker to power until ceiling installation

is completed and at least one source cable is connected.

Astronaut

DC Power

Astronaut

DC Power

Removable

Installation

POWER CONNECTION

Low Voltage Connection

The low power barrel connector J can now be plugged into

the speaker. Plugging/unplugging this connector will turn the

speaker on and off.

STEP 3

Power Up

When the power supply connector barrel is plugged into the

speaker the internal green light K will turn on, indicating the

speaker is on.

Turn on your sound source and adjust the volume.

STEP 2

CAUTION

Make sure all source cables are connected

before plugging in power barrel.

Diagram

Source Cable

(plug in 1st)

Power Supply

(plug in 2nd)

PLEASE READ ALL INSTRUCTIONS CAREFULLY AND KEEP A COPY OF THIS GUIDE IN A SAFE PLACE

Technical Support

TROUBLESHOOTING GUIDE C

This guide covers the most common issues encountered

with powered speakers. Perform this self-diagnostic

procedure prior to contacting us; it will help us further

diagnose any problem you are experiencing.

Most speaker difﬁ culties result from:

Poor connections Poor audio sources

Incorrect or unapproved power supplies

STEP 1

Check Connections

Make sure the power supply is fully plugged into the

power outlet and correct speaker terminal.

Make sure the audio source connections (CD, DVD,

PC, microphone, etc.) are fully plugged into the correct

speaker terminal.

Make sure all connections are tight otherwise noise

may occur.

STEP 2

Source Diagnostics

a. Computers and Laptops

Please refer to your computer's documentation.

Make sure the volume set on your computer

is turned up at least 50%.

Make sure CD/DVD’s or MP3 ﬁ les are playing

through your computer speakers before connecting

Cetacea Sound speakers.

b. Other Source Devices

Test multiple audio sources to isolate a device problem.

If you hear sound with one source device but not

another, then the sound source is faulty.

For faulty computers: the headphone or line-out jack

is not set up correctly in the computer software. Refer

to your computer’s documentation.

Technical Support

TROUBLESHOOTING GUIDE

STEP 3

Check Power

Verify that the green light L is on at the speaker input panel.

Verify the sound source is “ON” and playing.

DOs & DON'Ts

Don’t use unapproved power supplies. They could permanently

damage the ampliﬁ er or other components in your speaker.

Do educate all users in the proper use and handling of electronic

equipment, especially wires and cables.

TIP

In the case that your power supply fails, please recycle it

according to local laws. Older supplies can be returned to

us for a 25% discount on a new ENERGY STAR® model.

Page is loading ...

Cetacea ASTRO-XLR001-SFC User manual

Brand: Cetacea

Model: ASTRO-XLR001-SFC

Category: Interactive whiteboards

Type: User manual

This manual is also suitable for

Download PDF

report

Cetacea ASTRO-XLR001-SFC User manual

This manual is also suitable for

Cetacea ASTRO-XLR001-SFC User manual

Related papers

Other documents