AIC HA202-PV User manual

UM_HA202-PV_v1.1_061119

HA202-PV

Storage Barebone

User's Manual

Content

Table of Contents

Preface �� i

Safety Instructions �� ii

About This Manual �� iv

Chapter 1� Product Features ��1

1�1 Box Content ��1

1.2 Specications��2

1�3 Features ��3

Chapter 2� Hardware Setup ��7

2�1 Central Processing Unit Setup ��7

2.1.1 Processor Installation ........................................................................................7

2.1.2 CPU heatsink for each CPU ............................................................................. 10

2�2 System Memory ��11

2.2.1 Dual Processor ................................................................................................ 11

2.2.2 Recommended Dimm Installation Order ........................................................ 12

2.2.3 DIMM Installation ............................................................................................ 14

2�3 Top Cover ��15

2.3.1 Installing the top cover .................................................................................... 15

2.3.2 Removing the top cover .................................................................................. 15

2�4 Power Supply Unit Module ��16

2.4.1 Installing the Power Supply Unit ..................................................................... 16

2.4.2 Removing the Power Supply Unit ................................................................... 16

2�5 Node ��17

2.5.1 Installing the Node .......................................................................................... 17

2.5.2 Removing the Node ......................................................................................... 17

2�6 Fan Module ��18

2.6.1 Installing the fan module ................................................................................ 18

2.6.2 Removing the fan module ............................................................................... 18

2�7 Hard Disk Drive ��19

2.7.1 Installing the hard disk drive ........................................................................... 19

2.7.2 Removing the hard disk drive.......................................................................... 19

2�8 HDD Backplane Module ��20

2.8.1 Installing the HDD Backplane ........................................................................ 20

2.8.2 Removing the HDD Backplane ....................................................................... 20

2�9 Slide Rail Installation ��21

Chapter 3� Hardware Settings �� 24

3�1 Motherboard Block Diagram ��24

3�2 Motherboard Content List ��25

3�3 Motherboard Layout ��26

3�4 Internal Connectors/Jumpers ��27

3�5 System LED Indicator ��32

3.5.1 Front Panel LED .............................................................................................. 32

3.5.2 Rear I350 LAN LEDs......................................................................................... 32

3.5.3 Rear PCH LAN LEDs......................................................................................... 33

3.5.4 Rear UID LED & Internal LED ........................................................................... 34

3�6

HDD Backplane ��35

3.6.1 Layout ............................................................................................................... 35

3.6.2 Internal Connectors/Jumpers ......................................................................... 36

3�7 Bridge Board ��37

3.7.1 Layout ............................................................................................................... 37

3.7.2 Connector ......................................................................................................... 38

Chapter 4. BIOS Conguration Settings �� 39

4�1 Navigation Keys ��39

4�2 BIOS Setup ��40

4.2.1 Menu ................................................................................................................. 40

4.2.2 Startup .............................................................................................................. 40

4�3 Main ��43

4.3.1 Main .................................................................................................................. 43

4�4 Advanced ��44

4.4.1 Peripheral Conguration ................................................................................. 44

4.4.2 Video Conguration ......................................................................................... 44

4.4.3 Socket Conguration ....................................................................................... 44

4.4.4 PCH Conguration ........................................................................................... 48

4.4.5 H2o IPMI Conguration ................................................................................... 52

4.4.6 H2o Event Log Cong Manager ...................................................................... 53

4�5 Security �� 54

4.5.1 Security ............................................................................................................ 54

4�6 Power ��55

4.6.1 Power ............................................................................................................... 55

4�7 Boot ��56

4.7.1 Boot .................................................................................................................. 56

Content

4�8 Exit ��57

4.8.1 Exit .................................................................................................................... 57

Chapter 5. BMC Conguration Settings �� 58

5�1 Method 1 (Use the BIOS Setup) ��58

5�2 Method 2 (Use a Dos Tool - Syscheck) ��61

5�3 Login �� 63

5�4 Web GUI ��64

5.4.1 Menu Bar .......................................................................................................... 64

5.4.2 User Information and Quick Button ............................................................... 65

5.4.3 Dashboard: ....................................................................................................... 66

5.4.4 Sensor ............................................................................................................. 66

5.4.5 FRU Information ............................................................................................... 66

5.4.6 Logs and Report .............................................................................................. 67

5.4.7 Settings ........................................................................................................... 67

5.4.8 KVM Mouse Setting ........................................................................................ 68

Chapter 6� Technical Support �� 70

Content

This document contains proprietary information about

AIC products and is not to be disclosed or used except in

accordance with applicable agreements.

Document Release History

Release Date Version Update Content

June

2018

1 User's Manual release to public.

June

2019

1.1 Memory update

Copyright

No part of this publication may be reproduced, stored in a retrieval system, or

transmitted in any form or by any means, electronic, mechanical, photo-static, recording

or otherwise, without the prior written consent of the manufacturer.

Trademarks

All products and trade names used in this document are trademarks or registered

trademarks of their respective holders.

Changes

The material in this document is for information purposes only and is subject to change

without notice.

Warning

1. A shielded-type power cord is required in order to meet FCC emission limits and also

to prevent interference to the nearby radio and television reception. It is essential

that only the supplied power cord be used.

2. Use only shielded cables to connect I/O devices to this equipment.

3. You are cautioned that changes or modifications not expressly approved by the

party responsible for compliance could void your authority to operate the equipment.

Disclaimer

AIC shall not be liable for technical or editorial errors or omissions contained herein.

The information provided is provided "as is" without warranty of any kind. To the

extent permitted by law, neither AIC or its afliates, subcontractors or suppliers will be

liable for incidental, special or consequential damages including downtime cost; lost

profits; damages relating to the procurement of substitute products or services; or

damages for loss of data, or software restoration. The information in this document

is subject to change without notice.

Instruction Symbols

Special attention should be given to the instruction symbols below.

NOTE

This symbol indicates that there is an explanatory or

supplementary instruction.

CAUTION

This symbol denotes possible hardware impairment. Upmost

precaution must be taken to prevent serious harware damage.

WARNING

This symbol serves as a warning alert for potential body

injury. The user may suffer possible injury from disregard or

lack of attention.

Preface

i

Before getting started, please read the following important cautions:

• All cautions and warnings on the equipment or in the manuals should be noted.

• Most electronic components are sensitive to electrical static discharge. Therefore, be

sure to ground yourself at all times when installing the internal components.

• Use a grounding wrist strap and place all electronic components in static-shielded

devices. Grounding wrist straps can be purchased in any electronic supply store.

• Be sure to turn off the power and then disconnect the power cords from your system

before performing any installation or servicing. A sudden surge of power could

damage sensitive electronic components.

• Do not open the system’s top cover. If opening the cover for maintenance is a must,

only a trained technician should do so. Integrated circuits on computer boards are

sensitive to static electricity. Before handling a board or integrated circuit, touch

an unpainted portion of the system unit chassis for a few seconds. This will help to

discharge any static electricity on your body.

• Place this equipment on a stable surface when install. A drop or fall could cause injury.

• Please keep this equipment away from humidity.

• Carefully mount the equipment into the rack, in such manner, that it won’t be

hazardous due to uneven mechanical loading.

• This equipment is to be installed for operation in an environment with maximum

ambient temperature below 35°C.

• The openings on the system are for air convection to protect the equipment from

overheating. DO NOT COVER THE OPENINGS.

• Never pour any liquid into ventilation openings. This could cause fire or electrical

shock.

• Make sure the voltage of the power source is within the specification on the label

when connecting the equipment to the power outlet. The current load and output

power of loads shall be within the specification.

• This equipment must be connected to reliable grounding before using. Pay special

attention to power supplied other than direct connections, e.g. using of power strips.

• Place the power cord out of the way of foot traffic. Do not place anything over the

power cord. The power cord must be rated for the product, voltage and current marked

on the product’s electrical ratings label. The voltage and current rating of the cord

should be greater than the voltage and current rating marked on the product.

• If the equipment is not used for a long time, disconnect the equipment from mains to

avoid being damaged by transient over-voltage.

• Never open the equipment. For safety reasons, only qualified service personnel should

open the equipment.

Safety Instructions

ii

• If one of the following situations arise, the equipment should be checked by service

personnel:

1. The power cord or plug is damaged.

2. Liquid has penetrated the equipment.

3. The equipment has been exposed to moisture.

4. The equipment does not work well or will not work according to its user manual.

5. The equipment has been dropped and/or damaged.

6. The equipment has obvious signs of breakage.

7. Please disconnect this equipment from the AC outlet before cleaning. Do not

use liquid or detergent for cleaning. The use of a moisture sheet or cloth is

recommended for cleaning.

• Module and drive bays must not be empty! They must have a dummy cover.

CAUTION

The equipment intended for installation should be placed in Restricted Access

Location.

CAUTION

There will be a risk of explosion if battery is replaced by an incorrect type. Dispose

of used batteries according to the instructions. After performing any installation or

servicing, make sure the enclosure is correct in position before turning on the power.

CAUTION

This unit may have more than one power supply. Disconnect all power sources before

maintenance to avoid electric shock.

iii

Thank you for selecting and purchasing the HA202-PV.

This user's manual is provided for professional technicians to perform easy hardware

setup, basic system configurations, and quick software startup. This document pellucidly

presents a brief overview of the product design, device installation, and firmware settings

for HA202-PV. For the latest version of this user's manual, please refer to the AIC website:

https://www.aicipc.com/en/productdetail/50946.

Chapter 1 Product Features

HA202-PV is a flexible storage server barebone that is specifically designed to

accommodate diverse corporations and enterprises for managing heavy workloads and

multiple applications.

Chapter 2 Hardware Setup

This chapter displays an easy installation guide for assembling the hardware in this

product. Utmost caution for proceeding to set up the hardware is highly advised. Most of

the components are highly fragile and vulnerable to exterior influence. Do not endanger

the device by placing the device in an unstable environment.

Chapter 3 Hardware Settings

This chapter elaborates the overall layout of the server motherboard, including

multifarious connectors, jumpers, and LED descriptions. These descriptions assist users

to configure different settings and functions of the motherboard, as well as to confirm the

location of each connector and jumper.

Chapter 4 BIOS Configuration Settings

This chapter introduces the key features of BIOS, including the descriptions and option

keys for diverse functions. These details provide users to effortlessly navigate and

configure the input/output devices.

Chapter 5 BMC Configuration Settings

This chapter illustrates the diverse functions of IPMI BMC, including the details on logging

into the web page and assorted definitions. These descriptions are helpful in configuring

various functions through Web GUI without entering the BIOS setup. For more information

of BMC configurations, please refer to IPMI BMC (Aspeed AST2500) User's Manual for a

more detailed description.

Chapter 6 Technical Support

For more information or suggestion, please contact the nearest AIC corporation

representative in your district or visit the AIC website: http://www.aicipc.com/en. It is our

greatest honor to provide the best service for our customers.

About This Manual

iv

1

Chapter 1. Product FeaturesHA202-PV User Manual

♦ PACKAGE CONTENT MAY VARY PER REGION.

HA202-PV is a 2U high density storage server with 24 hot swap bays for dual-port

NVMe SSDs (U.2). For more information about our product, please visit our website at

http://www.aicipc.com/en/index.

Before removing the subsystem from the shipping carton, visually inspect the

physical condition of the shipping carton. Exterior damage to the shipping carton

may indicate that the contents of the carton are damaged. If any damage is found, do

not remove the components; contact the dealer where the subsystem was purchased

for further instructions. Before continuing, first unpack the subsystem and verify that

the number of components in the shipping carton is accurate and in good condition.

1�1 Box Content

This product contains the components listed below.

Please confirm the number and the condition of the components before installation.

• System chassis

(drive tray, fan, power supply unit)

• Power cord (vary per region)

• 28" Slide rail x 1 set (optional)

HA202-PV User Manual

Chapter 1� Product Features

2

Chapter 1. Product FeaturesHA202-PV User Manual

1.2 Specications

Dimensions

(W x D x H)

mm : 435 x 911 x 87

inches : 17.1 x 35.9 x 3.4

Motherboard

(per node)

AIC Server Board Pavo

Processor

(per node)

Processor

Support

• Intel® Xeon® Scalable Processors

(Skylake and next gen. CPU)

• Supports CPU TDP up to 150W

UPI Speeds

10.4 GT/s, 9.6 GT/s

Socket Type Socket P0 (LGA-3647 Socket)

Chipset Support

(per node)

Intel® Lewisburg C620 series PCH

System Memory

(per node)

• 6 x memory channels per CPU,

1 x DIMM per channel

• 16 x DIMM slots support:

2666/2400MHz RDIMM/LRDIMM

(feature supports up to DDR4 2933MHz

by next gen. process upgrade)

- up to 192GB RDIMM SRx4

- up to 384GB RDIMM DRx4

- up to 1536GB RDIMM 3DS 8Rx4

- up to 768GB LRDIMM QRx4

- up to 1536GB LRDIMM 3DS 8Rx4

• Intel® NVM DIMM (Apache Pass) support by

next gen. Purley Refresh CPU

Front Panel System power on/off

LEDs

A :

• Power (Secondary)

• Warning

B :

• Power (Primary)

• Warning

Drive Bays

External 2.5” hot swap 24

Internal 2.5” 2

Backplane 1 x 24-port dual loop NVMe backplane

Expansion Slots

(per node)

PCIe 3.0

• 1 x16 slot (FH)

• 1 x16 slot (x8 mode) (FH)

• 1 x OCP Mezzanine card V2.0

Expander Boards

(per node)

2 x 64-port Broadcom/PLX 9765 PCIe switch board

Riser Card

(included) (per node)

RC-PE2U08-TY 1 x16 PCIe slot + 1 x8 PCIe slot

System BIOS

BIOS Type

Insyde UEFI BIOS

BIOS Features

• ACP

• PXE

• WOL

• AC loss recovery

• Serial console

redirection

• BIOS Boot

• BIOS Recovery

Mode

• SMBIOS

• SRIOV

• iSCSI

• TPM

• PCIe Hotplug

On-board Devices

SATA

Intel® Lewisburg PCH on-chip solution

• 4 x SATA 6.0 Gb/s (by 1 x mini-SAS HD) +

2 x SATA 6.0 Gb/s (by 2 x SATA 7 pin)

• 5 x SATA 6.0 Gb/s (by Max I/O®)

BMC

Aspeed AST2500 Advanced PCIe Graphics

& Remote Management Processor

• Baseboard Management Controller

• Intelligent Platform Interface 2.0 (IPMI 2.0)

• iKVM, Media Redirection, IPMI over LAN,

Serial over LAN

• SMASH Support

• HTML5

Network

Controllers

• Intel® PCH (Lewisburg) Integrated

10GbE LAN Controller with dual SFP+

rear connectors

• Intel® I350 dual ports GbE RJ45 rear

connectors

• Realtek RTL8211E for BMC dedicated

management port

Graphics

Aspeed AST2500 Advanced PCIe Graphics

& Remote Management Processor

• PCIe VGA/2D Controller

• 1920x1200@60Hz 32bpp

Rear I/O

(per node)

LAN

• 2 x 10GbE SFP+

• 2 x GbE RJ45

• 1 x GbE RJ45 dedicated to BMC

management

USB

2 x USB 3.0 Type A

VGA

1 x external DB-15 VGA port

Serial Port

1 x audio jack for COM port

Power Supply

1300W 1+1 redundant power supply 80+ Platinum

• AC INPUT : 100-120V,50/60Hz,12A

• DC OUTPUT : 900W

• AC INPUT : 200-240V,50/60Hz,8A

• DC OUTPUT : 1300W

System Cooling

(per node)

2 x 60x56mm easy swap fans

System

Management

• IPMI 2.0

• KVM over IP

• Media redirection

• Temperature, fan, voltage, PSU sensor monitor

• System temperature

• System ID / System fail indicator

• Remote Power on/off/reset

• SEL message alarm through mail

• SNMP support

• Intel NM

• HTML5

Environmental

• Storage temperature : -10ºC(14ºF) ~ 60ºC(140ºF)

• Operating temperature : 0ºC(32ºF) ~ 35ºC(95ºF)

• Storage operating humidity : 5%~95% non-condensing

Gross Weight

(w/ PSU & Rail)

kgs : 43.5

lbs : 95.9

Packaging

Dimensions

(W x D x H)

mm : 615 x 1220 x 338

inches : 24.2 x 48 x 13.3

Mounting

Standard 28" tool-less slide rail

3

Chapter 1. Product FeaturesHA202-PV User Manual

HA202-PV is a reliable 2U storage server barebone with 24 hotswap drives bays. This

product is designed to accommodate the AIC-patented serverboard, Pavo, which supports

two Intel® Xeon® Scalable Processors and 16 DDR4 DIMM to offer greater perfomance,

efficiency, and utility for our customers. Featuring Intel® C620 Series Chipset, which is em-

phasized for its accelerated speed and expansion, this product enhances these advantag-

es by integrating flexible IO usage and system expansion into to provide greater bandwidth

and utilization.

In addition to the noteworthy features of the barebone, HA202-PV provides immediate and

efficient management with Onboard Baseboard Management Controller and greater I/O

extension. Featuring IPMI 2.0 and Aspeed AST2500 Advanced PCIe Graphics, the server

board offers support for iKVM, Media Redirection,Smash Support, IPMI over LAN, and Se-

rial over LAN.

• 2U 24 hot swap bays for dual port NVMe SSDs (U.2)

• High availability storage server optimized for mission critical, enetrprise-level storage

applications

• Fully redundant, fault-tolerant system supporting hot swappable controller nodes and

storage drives

• Two compute nodes, Active-Active configuration, each supporting two Intel®Xeon®

Scalable Processors

• 1 PCIe x16, 1 PCIe x8, 1 OCP Mezzanine x16 slots per node provide direct links to CPU

• PCIe NTB link between nodes for communication and fail over

• Customizable to meet OEM/ODM requirements

1�3 Features

4

Chapter 1. Product FeaturesHA202-PV User Manual

Front Panel

HA202-PV provides 1 system button (power) and 2 LED indicators for each node (A & B

node: power and warning LED).

24 x 2.5" hotswap drive bays

Power Button On

Canister A Power LED Green

Canister A fail LED Red

Canister B Power LED Green

Canister B fail LED Red

5

Chapter 1. Product FeaturesHA202-PV User Manual

Rear Panel

HA202-PV provides 3 PCIe slots per node (1 x PCIe x16 , 1 x PCIe Gen3 x8 , and 1 x OCP

Mezzanine card V2.0), 4 LAN ports (2x 10GbE SFP+, 2 x GbE Rj45), 1 GbE RJ45 port

dedicated to BMC management, 2 USB ports (3.0 Type A), 1 VGA port, and 1 audio jack for

COM port.

AC 1300 W 1+1

redundant

power supply 80+

Platinum

2 x 10GbE

SFP+ port

DB-15

VGA port

2 x USB 3.0

Type A

RJ45 port

for BMC

2 x GbE

RJ45 port

6

Chapter 1. Product FeaturesHA202-PV User Manual

Major Components

HA202-PV provides 24 x 2.5" external hotswap drive bays.

HA202-PV Top view Node top view

7

Chapter 2. Hardware SetupHA202-PV User Manual

This section describes a simple instruction guide for installing the hardware components

on the serverboard system. Turn off and unplug all system and peripheral devices before

proceeding.

2�1 Central Processing Unit Setup

The serverboard supports dual Xeon scalable processors and Socket P0 (LGA-3647).

2�1�1 Processor Installation

To ensure a safe and easy setup, you need to prepare before installation:

 a T20 Torx screwdriver

 ESD wrist strap/mat and conductive foam pad

CAUTION

The pins of the processor socket are vulerable and easily susceptible to damage if fingers

or any foreign objects are pressed against them. Please keep the socket protective cover on

when the processor is not installed.

CAUTION

When unpacking a processor, hold the processor only by its edges to avoid touching the

contacts.

Standard Processor Assembly:

A standard processor assembly is comprised of PHM(Processor Heatsink Module)

components and processor socket assembly.

Chapter 2� Hardware Setup

8

Chapter 2. Hardware Setup

HA202-PV User Manual

Processor Socket Assembly:

The server board includes two processor sockets (LGA-3647), supports one or two of

the Intel® Xeon® Processor Scalable Family and has a Thermal Design Power (TDP)

of up to 165W on selected models.

PHM (Processor Heatsink Module) Component:

This information is provided for professional technicians only.

9

Chapter 2. Hardware SetupHA202-PV User Manual

This information is provided for professional technicians only.

The PHM sits level with the processor socket assembly. The PHM is NOT installed

properly if it does not sit level with the processor socket assembly. Once the PHM is

seated over the processor socket assembly, the four heat sink torque screws must be

tightened in order as shown below.

Processor Heat Sink – Top View with Screw Tightening Order

CAUTION

Failure to tighten the heatsink screws in the specified order may cause damage to the

processor socket assembly. Heat sink screws should be tighted to 12 in-lbs torque

according to the indicated order on the top of the heatsink label.





 

10

Chapter 2. Hardware Setup

HA202-PV User Manual

2�1�2 CPU heatsink for each CPU

heatsink inside each node

CPU 0

CPU 1

Page is loading ...

AIC HA202-PV User manual

AIC HA202-PV User manual

Related papers

Other documents