Tyan B2865 User manual

Transport GT20

B2865

Service Engineer’s Manual

PREFACE

Copyright

This publication, including all photographs, illustrations, and soft-

ware, is protected under international copyright laws, with all rights

reserved. Neither this manual, nor any material contained herein,

may be reproduced without written consent of the manufacturer-.

Version 1.0

Disclaimer

Information contained in this document is furnished by TYAN Com-

puter Corporation and has been reviewed for accuracy and reliability

prior to printing. TYAN assumes no liability whatsoever, and dis-

claims any express or implied warranty, relating to sale and/or use of

TYAN products including liability or warranties relating to fitness for

a particular purpose or merchantability. TYAN retains the right to

make changes to product descriptions and/or specifications at any

time, without notice. In no event will TYAN be held liable for any

direct or indirect, incidental or consequential damage, loss of use,

loss of data or other malady resulting from errors or inaccuracies of

information contained in this document.

Trademark Recognition

All registered and unregistered trademarks and company names

contained in this manual are property of their respective owners

including, but not limited to the following.

TYAN and Transport GT20 B2865 are trademarks of TYAN Com-

puter Corporation.

Intel, Xeon, and combinations thereof are trademarks of Intel Corpo-

ration.

AMD, Opteron, Athlon, and combinations thereof are trademarks of

AMD Corporation.

Phoenix, PhoenixBIOS, and combinations thereof are trademarks of

Phoenix Technologies.

Microsoft Windows is a trademark of Microsoft Corporation.

IBM, PC, AT, PS/2 are trademarks of IBM Corporation.

Winbond is a trademark of Winbond Electronics Corporation.

Portable Document Format (PDF) is a trademark of Adobe Corpora-

tion.

ii

Federal Communications Commission (FCC)

Notice for the USA Compliance Information State-

ment (Declaration of Conformity Procedure) DoC FCC

Part 15: This device complies with part 15 of the FCC

Rules

Operation is subject to the following conditions:

1) This device may not cause harmful interference, and

2) This device must accept any interference received including inter-

ference that may cause undesired operation. If this equipment does

cause harmful interference to radio or television reception, which

can be determined by turning the equipment off and on, the user is

encouraged to try one or more of the following measures:

– Reorient or relocate the receiving antenna.

– Increase the separation between the equipment and the

receiver.

– Plug the equipment into an outlet on a circuit different from

that of the receiver.

Consult the dealer on an experienced radio/television technician for

help.

Notice for Canada

This apparatus complies with the Class B limits for radio interference

as specified in the Canadian Department of Communications Radio

Interference Regulations. (Cet appareil est conforme aux norms de

Classe B d’interference radio tel que specifie par le Ministere Cana-

dien des Communications dans les reglements d’ineteference

radio.)

Notice for Europe (CE Mark) This product is in conformity

with the Council Directive 89/336/EEC, 92/31/EEC

(EMC).

CAUTION: Lithium battery included with this board. Do not puncture,

mutilate, or dispose of battery in fire. Danger of explosion if battery

is incorrectly replaced. Replace only with the same or equivalent

type recommended by manufacturer. Dispose of used battery

according to manufacturer instructions and in accordance with your

local regulations.

iii

About this Manual

This manual provides you with instructions on installing your

Transport GT20. This manual is intended for experienced users and

integrators with hardware knowledge of personal computers.

This manual consists of the following parts

Chapter 1: Provides an Introduction to the Transport GT20

B2865 bare-bones, packing list, describes the

external components, gives a table of key compo-

nents, and provides block diagrams of the system.

Chapter 2: Covers procedures on installing the CPU, mem-

ory modules, an optional PCI-Express card, and

hard drives.

Chapter 3: Covers removal and replacement procedures for

pre-installed components

Appendix: Provides information on installing SMDC cards

and describes the differences between mainboard

BIOS and system BIOS. The cable connection

tables are also provided for reference of system

setup.

For information on the mainboard, please refer to the attached main-

board user’s manual. You can find the detailed description about

jumper and BIOS settings from the motherboard manual.

iv

SAFETY INFORMATION

Before installing and using the Transport GT20, take note of the fol-

lowing precautions:

– Read all instructions carefully.

– Do not place the unit on an unstable surface, cart, or stand.

– Do not block the slots and opening on the unit, which are pro-

vided for ventilation.

– Only use the power source indicated on the marking label. If

you are not sure, contact the Power Company.

– The unit uses a three-wire ground cable, which is equipped

with a third pin to ground the unit and prevent electric shock.

Do not defeat the purpose of this pin. If your outlet does not

support this kind of plug, contact your electrician to replace

your obsolete outlet.

– Do not place anything on the power cord. Place the power

cord where it will not be in the way of foot traffic.

– Follow all warnings and cautions in this manual and on the

unit case.

– Do not push objects in the ventilation slots as they may touch

high voltage components and result in shock and damage to

the components.

– When replacing parts, ensure that you use parts specified by

the manufacturer.

– When service or repairs have been done, perform routine

safety checks to verify that the system is operating correctly.

– Avoid using the system near water, in direct sunlight, or near

a heating device.

– Cover the unit when not in use.

v

Table of Contents

Chapter 1:Overview

1.1 About the Transport GT20 B2865 . . . . . . . . . . . . . . . . . . . . . . . . . 1

1.2 Product Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

1.3 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

1.4 Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

1.5 About the Product . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

1.5.1 Front View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

1.5.2 Rear View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

1.5.3 LED Definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

1.5.4 Internal View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

1.5.5 Motherboard Block Diagram. . . . . . . . . . . . . . . . . . . . . . . 10

1.5.6 Motherboard Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Chapter 2:Setting Up

2.0.1 Before You Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

2.0.2 Work Area. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

2.0.3 Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

2.0.4 Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

2.1 Rack Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

2.1.1 Installing the Server in a Rack. . . . . . . . . . . . . . . . . . . . . .15

2.2 Installing Motherboard Components. . . . . . . . . . . . . . . . . . . . . . . 21

2.2.1 Removing the Chassis Cover. . . . . . . . . . . . . . . . . . . . . . . 21

2.2.2 Installing the CPU and Heatsink . . . . . . . . . . . . . . . . . . . . 22

2.2.3 Installing the Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

2.2.4 Installing the PCI Card . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

2.3 Installing the External Hard Drive . . . . . . . . . . . . . . . . . . . . . . . . 28

2.4 Installing the Slim FDD (Option) . . . . . . . . . . . . . . . . . . . . . . . . . 30

Chapter 3:Replacing Pre-Installed Components

3.1 Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

3.1.1 Work Area . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

3.1.2 Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

3.1.3 Precautions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

3.2 Disassembly Flowchart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35

3.3 Removing the Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

3.4 Replacing Motherboard Components . . . . . . . . . . . . . . . . . . . . . . 37

3.4.1 Disconnecting All Motherboard Cables . . . . . . . . . . . . . . 37

3.4.2 Removing the Motherboard. . . . . . . . . . . . . . . . . . . . . . . . 40

3.5 Replacing the Slim CD-ROM . . . . . . . . . . . . . . . . . . . . . . . . . . . .41

3.6 Replacing the LED Control Board . . . . . . . . . . . . . . . . . . . . . . . . 43

vi

3.7 Replacing the M1012 Adapter Board . . . . . . . . . . . . . . . . . . . . . .45

3.7.1 M1012 Adapter Board Features for B5350 . . . . . . . . . . . . 46

3.7.2 System Fan Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47

3.7.3 M1012 Adapter Board Connector Pin Definition . . . . . . . 49

3.8 Replacing the SATA Backplane . . . . . . . . . . . . . . . . . . . . . . . . . .54

3.8.1 SATA Backplane Features. . . . . . . . . . . . . . . . . . . . . . . . . 56

3.9 Replacing the Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58

Appendix I: BIOS Differences

Appendix II: Cable Connection Tables

Appendix III: Installing SMDC Cards

Appendix IV: Driver CD Index

Chapter 1: Overview 1

Chapter 1: Overview

1.1 About the Transport GT20 B2865

Congratulations on your purchase of the TYAN Transport

TM

GT20 (B2865), a highly-optimized rack-mountable barebone

system. The Transport GT20 (B2865) is designed to support

AMD

®

Athlon™ 64/Opteron™ 100 939-pin processor, provid-

ing a rich feature set and incredible performance. Leveraging

advanced technology from AMD

®

, the Transport GT20

(B2865) server system is capable of offering scalable 32 and

64-bit computing, high-bandwidth memory design, and a

lightning-fast PCI-Express bus implementation. The Trans-

port

TM

GT20 (B2865) not only empowers your company in

today’s demanding IT environment but also offers a smooth

path for future application usage.

TYAN is also proud to deliver the Transport

TM

GT20 (B2865)

in SATA flavor while supporting up to four (4) hot-swap hard

drives, one (1) slim CD-ROM and one (1) optional slim floppy

disk drive (not included). The Transport

TM

GT20 (B2865)

uses TYAN’s latest tooling-made chassis featuring a robust

structure, tool-less and modularized design, and a solid

mechanical enclosure. All of this provides the Transport

TM

GT20 (B2865) the power and flexibility to meet the needs of

nearly any server application.

1.2 Product Model

Model HDD Bays

Hot-Swap

Support

HDD

Backplane

B2865G20S4H

Removable,

4 HDDs

Yes 4-port SATA

2 Chapter 1: Overview

1.3 Features

Enclosure

• Industry 19” rack-mountable 1U

chassis storage bay

– (4) 3.5” HDD bays

– (1) slim CD-ROM bay

– (1) slim FDD bay

• Dimension: D 22.4 x W 17.2 x H

1.72 inch (568x436x43.6mm)

Processor

• (1) uPGA 939-pin socket

•AMD

®

Athlon 64 939 Processor up

to Athlon 64 4000+ and Athlon 64

FX55

• Up to 1000 MHz Hyper-Transport

link support

Chipsets

• nVIDIA nForce4 Ultra

• SMSC DME1737

Memory

• Dual memory channels

• Supports up to 4 DDR-400/333

DIMMS

• Supports up to 4GB of Unbuffered,

ECC/non-ECC memory

Expansion Slot

• (1) x16 PCI Express connector for

graphics or

(1) 32-bit, 33 MHz PCI v2.3 slot

Back I/O Ports

• Stacked PS/2 mouse & keyboard

ports

• COM1 connector

• One 15-pin VGA port

• (4) USB 2.0 ports and (2) RJ45 con-

nectors

Front Panel Features

• I/O

– (2) USB 2.0 ports

• LED indicators

– Power LED

– (2) LAN LEDs

– HDD active LEDs

• Switches

– Power switch

– Reset switch

Integrated Storage Controller

• Single channel master mode sup-

ports two IDE devices

• Support for ATA-133/100/66/33 IDE

drives and ATAPI compliant devices

Storage

• Pre-installed slim type 24x CD-ROM

• (4) hot-swappable, SATA HDD with

RAID 1,0, 10

Networking

• (1) Gigabit Ethernet port (Broadcom

BCM5721 PCI-E GbE LAN control-

ler connected MCH), with teaming

feature support

• (1) nForce4 integrated MAC with

Marvell 88E1111-CAA Gigabit

Ethernet

Video

•ATI

®

RAGE

TM

XL PCI graphics

controller

• 8MB Frame Buffer of video memory

Motherboard

• TYAN Tomcat K8E S2865G2NR

system board

• ATX footprint 9.6” x 12” (244mm x

305mm)

BIOS

• Phoenix 8Mbit LCP Flash ROM

• Supports ACPI 1.0b & APM1.2

• PnP, DMI2.0 WFM2.0

• Power Management

Server Management

• Automatic fan speed control

• Chassis intrusion alert

• Tyan Server Management Support

• Tyan M3290 SMDC, IMPI v2.0 com-

pliant Remote server management

kit (option)

System Cooling

• (5) Sunon 40x40x28mm 14500 rpm

heavy-duty fans

• (1) passive CPU heatsink

Chapter 1: Overview 3

Power Supply

• EPS, 1U, 350W with PFC

• 100V~240V AC input

Regulatory

• FCC Class B (Declaration of Con-

formity)

• CE (Declaration of Congormity)

Environment Temperature

• Operating temperature 5

o

C~35

o

C

• Non-operating temperature -40

o

C ~

70

o

C

4 Chapter 1: Overview

1.4 Unpacking

If any items are missing or appear damaged, contact your

retailer or browse to TYAN’s Web site for service:

http://www.tyan.com.

The Web site also provides information on other TYAN prod-

ucts, plus FAQs, compatibility lists, BIOS settings, and more.

Driver Diskette

1 x Tyan driver CD

SMDC Mounting Kit

Power Cables

Left to right: Europe, US

HDD Screws

Mounting Ears & Screws

FDD Kit

FDD Cable

FDD Backplane Cable

FDD Installing Rails & Screws

Chapter 1: Overview 5

Mainboard Manual

Barebone Manual

Air Duct with Heatsink x 1

Rail Kit

Mounting Bracket x 4

Sliding Brackets

Front L-Bracket x 2

Rear L-Bracket x 2

Screws Kit

Sliding Rails x 2

2865

Tomcat K8E

6 Chapter 1: Overview

1.5 About the Product

The following views show you the product.

1.5.1 Front View

*Reserved: reserved for future upgrade

1.5.2 Rear View

CD-ROM Drive

Hard Drive Bay x 4

HDD activity LED

Power switch

Power LED

Reset switch

USB ports

Warning LED

LAN LEDs

*Reserved

Power Supply Socket

PS/2 Mouse/Keyboard Ports

Serial Port

VGA Port

2 LAN + 4 USB Ports

Power Supply Fan Aperture

PCI Card

Opening

Chapter 1: Overview 7

1.5.3 LED Definition

Front Panel

Rear I/O LED

LED Color State Description

Power Green

OFF

ON

OFF

Power ON

Power OFF

HDD Activity Amber

OFF

Random

Blink

OFF

HDD access activity

No disk activity

LAN1/LAN2 Linkage Green

Green

OFF

ON

Blinking

OFF

LAN linked

LAN accessing

No LAN linked

Warning Reserved LED for future upgrade. It is not functional in

the B2865 barebone now.

Hot Swappable HDD

Tray Power LED

Green

OFF

ON

OFF

Power connected

Power disconnected

Hot Swappable

HDD Tray Access

LED

Reserved LED for future upgrade. It is not functional in

the B2865 barebone now.

LED Color State Description

RJ45 NIC1 Linkage

(Left Side)

Green

OFF

ON

Blinking

OFF

LAN linked

LAN accessing

No LAN linked

RJ45 NIC1 Mode

(Right Side)

Amber

Green

OFF

ON

OFF

Gigabit mode

100M mode

10M mode

RJ45 NIC2 Linkage

(Left Side)

Green

OFF

ON

Blinking

OFF

LAN linked

LAN accessing

No LAN linked

RJ45 NIC2 Mode

(Right Side)

Amber

Green

OFF

ON

OFF

Gigabit mode

100M mode

10M mode

8 Chapter 1: Overview

1.5.4 Internal View

1

2

5

13

11

12

6

7

8

9

1. PCI-Express Slot

2. Link Bar

3. Memory Slots

4. Power Connectors

5. EPS Power Supply

6. Air Duct with Heatsink

7. Fans

8. M1012 Adapter Board

9. SATA Backplane

10. LED Control Board Cable

11. SATA Cables (4)

12. CD-ROM Cable

13. USB Cable

14. Four SATA HDD Bays

34

10

14

Chapter 1: Overview 9

1.5.5 Motherboard Block Diagram

10 Chapter 1: Overview

1.5.6 Motherboard Layout

PCI 1

J13

PCI 2

PCI 3

PCI 4

DIMM 1

DIMM 2

DIMM 3

DIMM 4

J22

J14

J18

J21

PCI E1

CPU

J32

J33

LPT

FDD

JP5

JP6

J45

J46

J

4

1

BIOS

J40

JP2

J35

J34

J31

J37

J38

1

J

4

3

1

V

I

A

V

T

6

3

0

7

JP3

1

PCI-E2PCI-E2

PCI-E3

ATI

RAGEXL

215R3LASB41

J28

1

J1P

1

BROADCOM

BCM572KF8

J23

1

P2W

PW1

J9

J8

1

SMSC

DME1737

nVIDIA

nForce Ultra

J17

J19

J12

1

11

111

1

111

1

11

1

11

1

11

1

Chapter 1: Overview 11

Jumpers & Connectors

Jumper

/Connector

Function

J45 Front Panel Header

J46 SMDC connector

J41/J43 IEEE 1394a Connectors

J40 COM2 Header

JP1 LAN2 DIsable Jumper

J8 Front Audio Header

J34/J35 Front Panel USB 2.0 Connectors

J19/J23 Front Panel LAN1/LAN2 Speed LED Pin Headers

J17/J28 Front Panel Lan1/LAN2 Link and Active LED

JP2 Clear CMOS Jumper

J13/J14/J18/

J21

Front Fan Connectors (Fan1/Fan2/Fan3/Fan4)

J12 Chassis FAN connector (Fan5)

J22 CPU_Fan Connector

J30/J37/J31/

J38

Serial ATA RAID Connectors

JP3 PCI Slot Volt Select Header

J9 CD_in Connector

Page is loading ...

Tyan B2865 User manual

This manual is also suitable for

Tyan B2865 User manual

Related papers

Other documents