Little GIANT 566597 User guide

Brand: Little GIANT

Model: 566597

Type: User guide

INTRODUCTION

This instruction sheet provides you with the information required

to safely own and operate your product. Retain these instructions

for future reference.

The product you have purchased is of the highest quality

workmanship and material, and has been engineered to give you

long and reliable service. This product has been carefully tested,

inspected, and packaged to ensure safe delivery and operation.

Please examine your item(s) carefully to ensure that no damage

occurred during shipment. If damage has occurred, please

contact the place of purchase. They will assist you in replacement

or repair, if required.

READ THESE INSTRUCTIONS CAREFULLY BEFORE

ATTEMPTING TO INSTALL, OPERATE, OR SERVICE

YOUR PRODUCT. KNOW THE PRODUCT’S APPLICATION,

LIMITATIONS, AND POTENTIAL HAZARDS. PROTECT

YOURSELF AND OTHERS BY OBSERVING ALL SAFETY

INFORMATION. FAILURE TO COMPLY WITH THESE

INSTRUCTIONS COULD RESULT IN PERSONAL INJURY AND/

OR PROPERTY DAMAGE!

SAFETY GUIDELINES

MAKE CERTAIN THAT THE UNIT IS DISCONNECTED FROM

THE POWER SOURCE BEFORE ATTEMPTING TO SERVICE

OR REMOVE ANY COMPONENT.

Do not use to pump flammable or explosive fluids such as gasoline,

fuel oil, kerosene, etc. Do not use in explosive atmospheres.

Pump should only be used with clean water. Do not use to pump

heated liquids. Pump should only be used with liquids compatible

with pump component material.

Do not handle pump with wet hands or when standing on a wet or

damp surface or in water.

This pump is supplied with a grounding conductor and/or

grounding type attachment plug. To reduce the risk of electric

shock, be certain that it is connected to a properly grounded

grounding type receptacle.

Support pump and piping when assembling and when installed.

Failure to do so may cause piping to break, pump or motor to

fall, etc.

Do not allow children or infants to play near the fountain due to

drowning hazard.

ELECTRICAL CONNECTIONS

1. Check the pump label for proper voltage required. Do not

connect to voltage other than that shown.

2. This pump is supplied with a 3-prong electrical plug. The third

prong grounds the pump to prevent possible electrical shock

hazard. DO NOT REMOVE the third prong from the plug.

A separate branch circuit is recommended. Do not use an

extension cord.

3. The National Electric Code requires that a ground fault circuit

interrupter (GFCI) be used in the branch circuit supplying

fountain pumps and other pond equipment.

4. To reduce the risk of electric shock, use only on portable, self-

contained fountains no larger than five feet in any dimension.

CONSULT THE PUMP INSTRUCTION SHEET ILLUSTRATIONS

FOR PROPER MAINTENANCE OF YOUR PUMP.

ASSEMBLY AND OPERATION

1. Consider the following needs of your fountain when determining

the appropriate location:

a. Enough space to create a hole approximately 10 inches

(0.25 m) deep and 36 inches (0.91 m) diameter, and will not

interfere with any buried utilities.

b. Utility needs of fountain:

i. 115 VAC/60 Hz power source within approximately

10 feet.

ii. Water source (garden hose) to periodically refill basin.

c. Existing landscape and the interaction of space.

2. Outline the basin and dig the hole for your basin (Fig. 3).

3. Place the basin in the hole and verify the following:

a. Top of basin is approximately at ground level (flush).

b. Top of basin is level in 2 directions: left to right, and front

to back. To correct non-level condition, remove basin and

spread sand in low-lying areas of hole. Replace basin and

measure again. Repeat until basin is leveled (Fig. 4).

c. Rotate basin to orient cord exit feature for expected

routing direction of pump power cord.

4. Backfill the basin. (Using stones or weight inside the basin will

help keep the basin in place during this step.) (Fig. 5).

5. Remove and clean all the debris from inside the basin.

6. The Papyrus fountain has an optional sand-fill port in its base

(Fig. 6). Turn fountain upside down, remove red plastic cap, and

pour sand into the hole. Re-install red plastic cap.

7. Screw four brackets to bottom surface of fountain (Fig. 7);

use the load bearing center column as a guide. Carefully

center column on fountain. Then, using the screws provided,

secure one bracket in each corner as shown (Fig. 8). DO NOT

ATTACH BRACKET TO THE COLUMN AT THIS TIME.

8. Place center column inside the basin, ensuring it is positioned

in the circular groove at bottom of basin, and oriented with the

feature shown in the figure (Fig. 9 and 10). Rotate the column

until it drops into place.

9. Prepare your fountain pump by following the instructions

below and illustration in Figure 1.

a. Remove pump from its carton.

b. Read the instruction sheet shipped with the pump. Pay

particular attention to all caution and warning statements.

Retain document for future reference.

c. Remove the discharge adaptor that is shipped with the pump.

d. Remove suction cup bracket from pump.

e. Thread the 2 fittings together, then thread both into the

pump’s discharge port.

f. Study the FLOW and orientation symbols on check valve

body. Then push the check valve over the fitting for a snug

fit (Fig. 1).

10. Apply lubricant to one end of the white flexible pipe (Fig. 11).

Black Papyrus Fountain Kit

Kit Fontaine Papyrus Noir, Bassin

Kit de Fuente Papiro Negra

PFK

Franklin Electric Co., Inc.

Oklahoma City, OK 73127-2010

www.lg-outdoor.com

[email protected]

Scan to watch

a step by step installation video

11. Push lubricated pipe end through center hole of the fountain.

(Fig. 12) Push it through so it is flush to the opposite side.

12. Slowly place fountain on center column, while routing loose end

of flexible pipe through central opening of column (Fig. 13).

13. Attach end of flexible pipe to the pump & fitting assembly (Fig.

14), while keeping the following in mind:

a. Attempt to place pump in a location that is convenient for

future access.

b. Pump should be placed on its side.

c. Ensure the horizontal orientation arrow on check valve

points vertically up after installation is complete.

14. If you are not installing the optional LED EggLites, skip to step 19.

15. Gently squeeze the cord nut into a slight oval shape (Fig. 15).

16. While holding the cord nut insert the cord and nut through the

desired location in the grate section.

17. Repeat the two steps above until the desired quantity of lights

are installed.

18. Complete the wiring of the LED EggLites by following the

instructions that are provided with the light kit.

19. To provide uniform flow around fountain edge, verify the

fountain is level in 2 directions: left to right, and front to back

(Fig. 16).

a. To correct out-of-level condition, insert shims (provided)

between fountain and support column (Fig. 17).

20. When leveling is complete, carefully screw the 4 brackets to

the column using the screws provided (Fig. 18).

21. Shims can now be broken-off flush to fountain to reduce

visibility of installed shim.

22. Install all basin grates around fountain, except the one just

above your pump.

23. Fill basin with water (Fig. 19).

24. When basin is at least ¾ full, turn the pump on. Continue filling

basin with water until both fountain and basin are full.

25. Ensure fountain is still level in both directions, and adjust if

necessary.

26. Your pump includes a flow control at the inlet. For small

adjustments to the fountain’s water flow, first turn off the pump

by disconnecting the unit from the power source. Adjust the

flow control faster (+) or slower (-) as desired. Re-connect the

pump’s power source and verify the flow, repeat as needed

until the desired flow is achieved.

27. Place the last basin grate over the pump.

28. Place decorative material on top of all basin grates (Fig. 20).

a. The small holes in each basin grate are 5/8” diameter.

Attempt to purchase decorative material, such as landscape

rock, that is slightly larger in size to prevent falling into lower

basin where pump is.

b. NOTE: to provide maximum stability of water fountain, it is

required for the decorative material to be heavy, such as

landscape rock or similar.

29. For maximum pump life, it is important the water level in basin

never drop below that which causes the pump to run dry. To

establish the frequency of refilling the basin level:

a. Monitor your basin water levels on a daily basis during the

first week. When the level gets within 1 inches of the top of

pump (Fig. 2), refill with garden hose.

b. Hot and dry conditions will cause greater evaporation, and

more frequent refilling will be required.

MAINTENANCE

WARNING: Disconnect the pump from the power source before

attempting to service or remove any component.

WARNING: Do not modify, cut, saw, sand, or grind any part of the

pump. Doing so can cause harmful emissions.

1. Do not allow the pump to run without water. Check basin

water levels frequently, and fill when level drops within 1 inch

of pump top. Note that hot and dry weather will cause greater

evaporation, and more frequent refilling will be required.

2. Clean fountain only with water and, if desired, use only

fountain cleaner to prevent algae. DO NOT USE BLEACH.

3. Refer to the Service section of your pump’s manual when

performing routine cleaning and maintenance.

4. Remove pump before freezing conditions exist.

TROUBLESHOOTING

PROBLEM

1. Pump is not working.

2. Pump is working but water is not flowing.

3. Water is flowing into basin when pump is off.

CORRECTIVE ACTION

1. Check power outlet. Refer to manufacturer’s instructions.

2. Check for kinks in the tube. Make sure pump is submerged.

Make sure pump is free of debris.

3. Ensure the check valve is installed (Fig. 1).

INTRODUCTION

Cette feuille d’instructions vous fournit les informations nécessaires

pour entretenir et faire fonctionner votre produit. Conserver ces

directives afin de pouvoir les consulter plus tard.

Le produit que vous avez acheté a été soigneusement fabriqué

avec des matériaux de la plus haute qualité et a été conçu pour

durer longtemps et offrir un service fiable. Les produits sont

soigneusement testés, inspectés et emballés afin d’en assurer la

sécurité de fonctionnement et une livraison en bonne condition.

Vérifier attentivement le produit afin de vous assurer qu’il n’a pas

été endommagé pendant le transport. S’il est endommagé, veuillez

contacter l’entreprise qui vous l’a vendu. Si une réparation ou un

remplacement est requis, elle vous prêtera assistance.

LIRE ATTENTIVE MENT CES DIRECTIVES AVANT DE PROCÉDER

À L’INSTALLATION, À L’UTILISATION OU À L’ENTRETIEN

DU PRODUIT. SE FAMILIARISER AVEC LES APPLICATIONS,

LES LIMITES ET LES RIS QUES POTENTIELS DU PRODUIT.

ASSURER SA PROPRE PROTECTION ET CELLE DES AUTRES

EN SUIVANT TOUTES LES RÈGLES DE SÉCURITÉ. LE

NONRESPECT DE CES DIRECTIVES PEUT ENTRAÎNER DES

BLESSURES ET/OU DES DOMMAGES MAT ÉRIELS!

AVERTISSEMENT

VEILLER À DÉBRANCHER L’APPAREIL DE SA SOURCE

D’ALIMENTATION ÉLECTRIQUE AVANT L’ENTRETIEN OU LA

DÉPOSE D’UNE OU DE PLUSIEURS PIÉCES.

Ne pas pomper des fluides explosifs ou inflammables tels

qu’essence, mazout, kérosène, etc. Ne pas employer dans une

atmosphère comportant des risques de déflagration. La pompe ne

doit servir qu’à pomper des liquides compatibles avec les matériaux

utilisés pour la fabrication des éléments qui la composent.

Ne pas manipuler la pompe les mains humides, les pieds posés

sur une surface mouillée ou humide, ou les pieds dans l’eau.

Page is loading ...

• Min water level

• Faible niveau

• Nivel de agua mínimo

1.0"

(25mm)

• Pump

• Pompe

• Bomba

Fig. 2

Fig. 3 Fig. 4

Fig. 5 Fig. 6

Page is loading ...

LIMITED WARRANTY

THIS WARRANTY SETS FORTH THE COMPANY’S SOLE OBLIGATION

AND PURCHASER’S EXCLUSIVE REMEDY FOR DEFECTIVE

PRODUCT.

Franklin Electric Company, Inc. and its subsidiaries (hereafter “the

Company”) warrants that the products accompanied by this warranty

are free from defects in materials or workmanship of the Company that

exist at the time of sale by the Company and which occur or exist within

the applicable warranty period. Any distributor, sub-distributor, recipi-

ent, end-user and/or consumer agrees that by accepting the receipt of

the products, the distributor, sub-distributor, recipient, end user and/or

consumer expressly agrees to be bound by the terms of the warranty

set forth herein.

I. Applicable Warranty Period

The products accompanied by this warranty shall be covered by this

Limited Warranty for a period of 12 months from the date of original

purchase by the consumer. In the absence of suitable proof of pur-

chase date, the warranty period of this product will begin to run on the

product’s date of manufacture.

II. Instructions Applicable to this Limited Warranty

1. Consumers wishing to submit a warranty claim must return the

products accompanied by this warranty to the point of purchase

for warranty consideration.

2. Upon discovery of a defect, any personal injury, property damage

or any other type of resulting damage, if applicable, shall be

reasonably mitigated to the extent possible.

3. At its discretion, the Company may inspect products either at its

facilities or in the field, and after determination of a warranty claim,

will, at its option, repair or replace defective parts. Repaired or

replaced parts will be returned freight prepaid by the Company.

4. This warranty policy does not cover any labor or shipping

charges. The Company shall not be liable for any costs or charges

attributable to any product testing, maintenance, installation,

repair or removal, or for any tools, supplies, or equipment needed

to install, repair, or remove any product.

III. Limitations Applicable to this Limited Warranty

THIS WARRANTY DOES NOT APPLY TO ANY OF THE FOLLOWING:

1. Any product that is not installed, applied, maintained and

used in accordance with the Company’s published instructions,

applicable codes, applicable ordinances and/or with generally

accepted industry standards.

2. Any product that has been subject to misuse, misapplication, neglect,

alteration, accident, abuse, tampering, acts of God (including

lightning), acts of terrorism, acts of war, fire, improper storage or

installation, improper use, improper maintenance or repair, damage

or casualty, or to an excess of the recommended maximums as set

forth in the product instructions.

3. Any product that is operated with any accessory, equipment,

component, or part not specifically approved by the Company.

4. Use of replacement parts not sold by the Company, the unauthorized

addition of non-Company products to other Company products,

and the unauthorized alteration of Company products.

5. Products damaged by normal wear and tear, normal maintenance

services and the parts used in connection with such service, or any

other conditions beyond the control of the Company.

6. Any product that has been used for purposes other than those for

which it was designed and manufactured.

7. Any use of the product where installation instructions and/or

instructions for use were not followed.

The Company reserves the right at any time, and from time to time, to

make changes in the design and/or improvements upon its product

without thereby imposing any obligation upon itself to make corre-

sponding changes or improvements in or upon its products already

manufactured and/or previously sold. The Company further reserves

the right to substitute parts or components of substantially equal quality

in any warranty service required by operation of this Limited Warranty.

This written Limited Warranty is the entire warranty authorized and

offered by the Company. There are no warranties or representations

beyond those expressed in this document.

THIS WARRANTY AND REMEDY IS IN LIEU OF ALL OTHER

WARRANTIES AND REMEDIES INCLUDING WITHOUT LIMITATION,

WARRANTIES OF MERCHANTABILITY AND/OR FITNESS FOR A

PARTICULAR PURPOSE, WHICH ARE HEREBY SPECIFICALLY

DISCLAIMED AND EXPRESSLY EXCLUDED. CORRECTION OF NON-

CONFORMITIES, IN THE MANNER AND FOR THE PERIOD OF TIME

AS SET FORTH ABOVE, SHALL CONSTITUTE FULFILLMENT OF

ALL LIABILITY OF THE COMPANY TO THE PURCHASER WHETHER

BASED ON CONTRACT, NEGLIGENCE, OR OTHERWISE.

THE COMPANY SHALL NOT BE LIABLE FOR INCIDENTAL,

CONSEQUENTIAL OR SPECIAL DAMAGES SUCH AS, BUT NOT

LIMITED TO:

DAMAGE TO OR LOSS OF OTHER PROPERTY OR EQUIPMENT,

LOSS OF USE OF EQUIPMENT, FACILITIES OR SERVICE,

LOSS OF PROFIT OR SALES, COST OF PURCHASES OR

REPLACEMENT GOODS, CLAIMS OF CUSTOMERS OF THE

PURCHASER, FAILURE TO WARN AND/OR INSTRUCT, LOSS

OF OTHER PRODUCTS, OR COSTS OF ENVIRONMENTAL

REMEDIATION, OR DIMINUTION IN PROPERTY VALUE. THE

REMEDIES OF THE PURCHASER SET FORTH HEREIN ARE

EXCLUSIVE, AND THE LIABILITY OF THE COMPANY SHALL

NOT, EXCEPT AS EXPRESSLY PROVIDED HEREIN, EXCEED THE

PRICE OF THE PRODUCTS UPON WHICH SUCH LIABILITY IS

BASED. DAMAGES AS SET FORTH IN THIS PARAGRAPH SHALL

BE REASONABLY MITIGATED TO THE EXTENT POSSIBLE.

THIS PARAGRAPH SHALL ALSO APPLY TO ALL DAMAGES

RESULTING FROM CONDITIONS SET FORTH IN SECTION III

ABOVE AND (1) DEFECTS IN PRODUCT PROTOTYPES OR

REPLACEMENT PART PROTOTYPES THAT HAVE NOT BEEN

PUT INTO PRODUCTION, CIRCULATED AND SOLD BY THE

COMPANY, AND/OR (2) DEFECTS THAT WERE NOT FOUND AT

THE TIME OF SALE DUE TO SCIENTIFIC AND TECHNOLOGICAL

REASONS.

This Limited Warranty gives you specific legal rights. You may have

other rights, which vary according to the applicable laws and regula-

tions. Where any term of this warranty is prohibited by such laws, it

shall be null and void, but the remainder of this warranty shall remain

in full force and effect.

DISCLAIMER: Any oral statements about the product made by the

seller, the Company, the representatives or any other parties, do not

constitute warranties, shall not be relied upon by the user, and are not

part of the contract for sale. Seller’s and the Company’s only obligation,

and buyer’s only remedy, shall be the replacement and/or repair by the

Company of the product as described above. Before using, the user

shall determine the suitability of the product for his intended use, and

user assumes all risk and liability whatsoever in connection therewith.

GARANTIE LIMITÉE

LA PRÉSENTE GARANTIE ÉNONCE LA SEULE OBLIGATION

DE LA SOCIÉTÉ ET LE RECOURS EXCLUSIF DE L’ACHETEUR

POUR UN PRODUIT DÉFECTUEUX.

Franklin Electric Company, Inc et ses filiales (ci-après « la Société

») garantit que les produits accompagnés de cette garantie sont

exempts de défauts de matériaux ou de fabrication de la Société

existant au moment de la vente par la Société et qui se produisent ou

existent pendant la période de garantie applicable. Tout distributeur,

sous-distributeur, destinataire, utilisateur final et/ou consommateur, en

acceptant la réception des produits, convient que le distributeur, sous-

distributeur, destinataire, utilisateur final et/ou consommateur accepte

expressément d’être lié par les termes de la garantie qui y sont énoncés.

Page is loading ...

Little GIANT 566597 User guide

Brand: Little GIANT

Model: 566597

Type: User guide

Download PDF

report

in other languages

français: Little GIANT 566597 Mode d'emploi
español: Little GIANT 566597 Guía del usuario

Little GIANT 566597 User guide

Little GIANT 566597 User guide

in other languages

Related papers

Other documents