PRN: AIM-50-0171-KOL [15.11.05]
Important Information:
Before you begin assembly, please read these directions. See next
page for important warning statements on this product. After product is
assembled make sure all bolts and screws are securely tightened.
ROCKING MOSES BASKET STAND
WARNING
! IMPORTANT — Read the instructions carefully before use and keep them for
future reference.
! WARNING: Use only on a firm ground which is horizontal, level and dry.
! WARNING: Do not let other children play unattended near the carry cot and
stand.
! WARNING: Do not use if any part is broken, torn or missing. Only use My Child
approved parts.
! When the stand is not in use, it must be put away.
! This stand is designed to hold a Moses Basket with a base between 68-79cm
long and 30-37cm wide.
! If you use POWER TOOLS to assemble this product, use on the LOWEST SETTING
to avoid over tightening and splitting the wood.
! To prevent entrapment, do not place the Moses Basket and Stand near to
other objects.
! After product is assembled make sure all screws are securely tightened.
! Regularly check that fixings are secure. Natural wood product: Clean with
damp cloth.
! DO NOT use bleach, solvents or abrasives.
2
PART LIST
Set #/ 08-07002-SV :
Fixtures and Fittings supplied (actual size)
55mm Allen Head Screw
#07-07000-SV
Fixtures and Fittings supplied (not to scale)
20
4
8
QTYE
Name
30mm Wood Pin
#07-35001
A
B
C
Ref.
1 "1" 2" " 2 " 3"
Head
mm 10 20 30 40 50 60 70 80
1
Allen Key
#07-00001
D
17mm Screw
#07-01300
HARDWARE
(1) Leg
Part #: 07-35277
(2 pcs)
(2) Leg
Part #: 07-35266
(2 pcs)
(4) Curved Base Rail
Part #: 07-35170
(2 pcs)
(5) Dowel Cross Rail
Part #: 07-35121
(4 pcs)
(6) Plastic Rail
Part #: 07-35100
(2 Pcs)
(3) Side Rail (One with Warning Label attached)
Part #: 07-35124
(2 pcs)
3
02-20002 [15.11.04]
BS EN 1466:2004
Moses Basket with a base between
68-79cm long and 30-37cm wide
This stand is designed to hold a
Model #:
Colour:
Date:
Shipment Ref. #:
ROCKING MOSES BASKET STAND
Place legs
with the
larger holes
facing
towards
you.
ASSEMBLY INSTRUCTIONS
1
3
3
B
! Insert Wooden Pins (B) into the top hole on the Side Rails (3) on both ends. Repeat for other side rail.
3
1a
2
! To attach the Side Rail (3) to the Legs (1 & 2) simply line up the wooden pins you inserted in Step 1 into
the top hole on the flat surface of the legs. Ensure that you have one (1) leg and one (2) leg as shown in
image. Bolt together using the 55mm Allen Head bolt (A) tightening with Allen key (D). Repeat for
other side.
Note: Angled edge of legs face
outwards as shown with the larger
holes for the cross dowels on the same
side facing in.
The pilot
holes for the
plastic strap
should face
inside.
2a
3
1
2
3
1
A
B
D
3
4
1
2
3a
! Attach the Curved Base Rail (4) to the leg assembly with four
55mm Allen Head Bolts (A) as shown. Ensure bolts are
tightened securely. Repeat for other side.
1
4
A
A
D
4
ASSEMBLY INSTRUCTIONS
4
4a
5
A
1
! Insert one of the end of the Dowel Cross Rails (5) into the large hole on the side assembly. The dowel
should go into the hole tightly as shown in 4a. Some gentle tapping may be required. Bolt the dowel
into place with a 55mm Allen Head Bolt (A) and tighten in place. Repeat for the three other ends of
the dowels.
5
5
5
5
1
2
D
5
! Place partially assembled unit on its side as shown.
Line up the second side assembly with the four
dowels and press together. Ensure the dowels are
fully inserted into the holes. Secure in place with
four 55mm Screws (A) as shown.
1
5
5
5
5
2
5a
1
5
A
D
6
! Attach the Plastic Rail (6) by first lining up the two
holes on the end with the two guide holes on the Side
Rails (3) as shown in 6a. You will need a Philips screw
driver for this task (not supplied). Screw firmly in place.
Repeat for other end of plastic rail. When done
simply attach the other plastic rail to the other
end as shown.
6
6
C
2
1
3
1
2
6a
6
3
1
C
C
3
5
MADE IN CHINA
Notes:
Model #:
Colour:
Date:
Shipment Ref. #:
Kooltrade Ltd.
3 Orbital Way, Denton
Manchester, M34 3QA
6
Product Packaging Information
/
