fantastic furniture SUNBURY Assembly Instructions Manual

Brand: fantastic furniture

Model: SUNBURY

Type: Assembly Instructions Manual

Assembly Instructions

SUNBURY

Twinkle Cot / Junior Bed

Ver1.1

WARNINGWARNING

FAILURE TO FOLLOW THESE BASIC STEPS CAN LEAD TO DAMAGE

THAT IS NOT COVERED BY YOUR WARRANTY

Read Instructions carefully.

Check no parts are missing.

Lay out all of the components on a soft surface

as if you were preparing to do a jigsaw puzzle.

Carefully identify each component, especially

those that are similar. The most common mistake

is getting things back to front.

Separate and identify each component from the

hardware pack and rest each one in its proper

Location before fastening.

DO NOT fully tighten screws(leave slightly loose) .

When the item is fully assembled

tighten the screws - but do not over tighten.

Page 2

What you Need

To Assemble the Cot

Cot End

Cot Side

Base

Bed Rail

Page 3

Please make sure you have all these parts before you start.

65mm 40mm 19mmBOLT

Cross Dowel

20mm

Cross Dowel

13mm

Wood Dowel Allen Key

BOLT BOLT Cap

Step 1

Attach the base (noting the appropriate height level for your baby) (P3)to one end (P1). Affix the 2

x 65mm bolts (H1) using the Allen key(H8) through the outside of the end and align with the base

and use 2 x cross dowel (H5) as per above. Do not over tighten or bolts may cross thread.

You will need:

2x Bolts

(H1)

(H5)

Allen key

(H8)

2x Cross Dowel

Step 2

Repeat step 1 to connect the other end.

Page 4

You will need:

2 x Bolts

(H1)

(H5)

Allen key

(H8)

2x Cross Dowel

Step 3

You will need:

Step 4

Next, attach either of the sides (P2) with one person at either end. Place a 40mm bolt (H2)

through each of the 4 holes at the outside of the end (P1)and fix using the Allen Key (H8).

Do not over tighten or bolts may cross thread. Tighten only until the bolt is engaged at this

stage. DO NOT ATTEMPT TO INSTALL THE BED RAILS (P4) AND COT SIDES

(P2)SIMULTANEOUSLY..

4x Bolts

(H2)

Allen key

(H8)

Repeat step 3 to connect the other side (P2).

Step 4

Page 5

4x Bolts

(H2)

Allen key

(H8)

Step 5

You will need:

4x Bolts

(H3)

(H4)

4x End Caps

You will need:

Bolts

Allen key

(H8)

Install Bolts (H3) and end caps (H4) in holes not being used as indicated on

(P1) All bolts can now be tightened using the Allen Key (H8) Do not over

tighten.

Affixing Bed Rails (P4)

When it is time to replace the cot sides (P2) with the bed rails (P4) provided, first ensure the

base (P3) is in the lower position and loosen the base bolts (H1) using the Allen Key (H8) to

allow removal of the sides (P2). Remove one cot side(P2) using the Allen Key (H8). Place

the 4 x wood dowel (H7) into each end of the bed rail (P4). Place the 4 x cross dowels

(H6) in the hole on the side of the bed rail (P4)(with screwdriver slot facing out and parallel

to the bed rail (P4)). Align the end of the bed rail (P4) with the 2 holes at the end of the cot

(P1). Affix a 65mm bolt (H1) through the outside of the end (P1) and align with the cross

dowel (H6). Tighten with the Allen Key (H8) only until the cross dowel (H6) is engaged.

Remove the other cot side (P2) using the Allen Key (H8). Affix the second bed rail, following

the same procedure as above for the other side. Tighten all bolts, taking care not to over

tighten.

Page 6

Bolts

(H1)

(H6)

4 x cross dowel

4x Wood Dowel

(H7)

(H8)

Allen key

Sunbury Nursery Furniture

4/56 Cambridge Street, Coorparoo,

Qld 4151

Phone: 07 3847 3699,

Fax: 07 3397 1146

E-mail: sales@sunburynursery.com.au

WARNINGS

PLEASE ENSURE THE INSTRUCTIONS ARE FOLLOWED CAREFULLY TO ENSURE

THE SAFETY OF THIS COT IS NOT COMPROMISED:

Dispose of any wrapping immediately to avoid danger of suffocation.

Ensure the enclosed assembly instructions are followed in detail.

Ensure the cot is placed at a reasonable distance from curtains, blinds, heaters and power

points.

Keep medication, string, elastic, small toys and small items such as money out of reach

from any position in the cot.

WARNING: TO PREVENT FALLS, THE MATTRESS BASE OF THIS COT SHOULD BE

ADJUSTED TO THE LOWEST POSITION BEFORE THE CHILD CAN SIT UP.

In case of the cot being damaged in any way, please do not continue to use it, as this

could cause injury or harm.

Ensure that your child is clear of any moving parts when accessing the dropside.

Page 7

Ensure that your child is clear of any moving parts when accessing the dropside.

Ensure the wheels have the brakes locked while the cot is in use.

When using the dropside, ensure you first lift and then push the pins at either end

simultaneously. This dropside can be lifted using 1 or 2 hands. Ensure that the dropside

locks into the upper position when raised.

RECOMMENDED MATTRESS SIZE: This cot has been manufactured for use with a

mattress which measures 690mm wide x 1300mm long and 120mm in thickness. The

width and length are specified because it is important that the gaps between the mattress

and the sides and ends of the cot will not exceed 40mm. This is to minimise the risk of a

child’s limb becoming caught in the gap. The thickness of the mattress has been specified

to ensure that the depth of the cot is greater than 500mm with the mattress base in the

lower position to minimize the risk of a child climbing or falling out of the cot.

Please retain your sales receipt for proof of purchase and warranty.

fantastic furniture SUNBURY Assembly Instructions Manual

fantastic furniture SUNBURY Assembly Instructions Manual

fantastic furniture SUNBURY Assembly Instructions Manual

Other documents