3M Adper™ Prompt™ L-Pop™ Self-Etch Adhesive Economy Pack,41928 500ct is a dental adhesive system designed for direct light-cure restorations, sealing pits and fissures, and treating hypersensitive root surfaces. It features a unique unit-dose delivery system that ensures proper activation and dispensing of the adhesive and activator. The self-etching formula eliminates the need for a separate acid-etch step, saving time and reducing patient discomfort. The adhesive provides a strong and durable bond to both enamel and dentin, making it ideal for a variety of restorative procedures.
3M Adper™ Prompt™ L-Pop™ Self-Etch Adhesive Economy Pack,41928 500ct is a dental adhesive system designed for direct light-cure restorations, sealing pits and fissures, and treating hypersensitive root surfaces. It features a unique unit-dose delivery system that ensures proper activation and dispensing of the adhesive and activator. The self-etching formula eliminates the need for a separate acid-etch step, saving time and reducing patient discomfort. The adhesive provides a strong and durable bond to both enamel and dentin, making it ideal for a variety of restorative procedures.
using
Adper
TM
Prompt
TM
Self-Etch Adhesive
3M, ESPE, Adper, Clinpro,
L-Pop and Prompt are
trademarks of 3M or
3M ESPE AG. Used under
license in Canada.
70-2009-3821-8
Dental Products
3M Center
Building 275-2SE-03
St. Paul, MN 55144-1000
USA
1-800-634-2249
©3M 2006.
All rights reserved.
Printed in U.S.A.
10% post-consumer
waste paper
3M Canada
Post Office Box 5757
London, Ontario N6A 4T1
Canada
1-800-265-1840 ext. 6229
3M ESPE Customer Care Center 800-634-2249
www.3MESPE.com/adperprompt
ILLUSTRATED INSIDE:
• How to properly activate the
L-Pop
™
Applicator
• Direct light-cure restoration
• Sealing pits and fi ssures with
the NO-RINSE sealant technique
• Treating hypersensitivity
Adper
™
Prompt
™
L-Pop
™
Self-Etch Adhesive
Proper Activation and Dispensing
Proper activation is the key to ensuring the proper
mix of adhesive and activator … and for achieving
excellent clinical results.
Easy to Activate
• The L-Pop
™
unit-dose applicator allows for easier
flow of material from one chamber to the next.
• When the material moves from the red chamber
to the yellow chamber, the indentation in the yellow
chamber pops up to show that the material has
properly transferred.
Spin or churn applicator
for 5 seconds to mix the
adhesive.
2
Fold
The adhesive’s subtle yellow
tint acts as a visual cue that the
product has been properly mixed.
Activation and Dispensing
Squeeze the material from the
red reservoir into the yellow
(middle) reservoir. The yellow
reservoir will expand indicating
transfer of fluid.
Carefully fold back the red
reservoir until it meets the flat face
of the yellow reservoir. Keep
the red reservoir tightly squeezed
while bending the package to
keep material from flowing back.
Squeeze the liquid from the
yellow reservoir into the
green reservoir.
Fully coat the applicator tip
and apply.
Greater Bonding ConfidenceTechnique Guide
How to get
Breakthrough
Performance
Press
1
Press
3
Confirm
5
Spin
4
Apply
6
For maximum effectiveness, follow
the simple steps outlined here to
ensure proper activation.
Adper
TM
Prompt
TM
Self-Etch Adhesive
Available in our innovative, disposable
unit-dose delivery, or vial
delivery system.
Please refer to instructions for
more detailed information, as well as
precautionary and warranty information.
using
Adper
TM
Prompt
TM
Self-Etch Adhesive
3M, ESPE, Adper, Clinpro,
L-Pop and Prompt are
trademarks of 3M or
3M ESPE AG. Used under
license in Canada.
70-2009-3821-8
Dental Products
3M Center
Building 275-2SE-03
St. Paul, MN 55144-1000
USA
1-800-634-2249
©3M 2006.
All rights reserved.
Printed in U.S.A.
10% post-consumer
waste paper
3M Canada
Post Office Box 5757
London, Ontario N6A 4T1
Canada
1-800-265-1840 ext. 6229
3M ESPE Customer Care Center 800-634-2249
www.3MESPE.com/adperprompt
ILLUSTRATED INSIDE:
• How to properly activate the
L-Pop
™
Applicator
• Direct light-cure restoration
• Sealing pits and fi ssures with
the NO-RINSE sealant technique
• Treating hypersensitivity
Adper
™
Prompt
™
L-Pop
™
Self-Etch Adhesive
Proper Activation and Dispensing
Proper activation is the key to ensuring the proper
mix of adhesive and activator … and for achieving
excellent clinical results.
Easy to Activate
• The L-Pop
™
unit-dose applicator allows for easier
flow of material from one chamber to the next.
• When the material moves from the red chamber
to the yellow chamber, the indentation in the yellow
chamber pops up to show that the material has
properly transferred.
Spin or churn applicator
for 5 seconds to mix the
adhesive.
2
Fold
The adhesive’s subtle yellow
tint acts as a visual cue that the
product has been properly mixed.
Activation and Dispensing
Squeeze the material from the
red reservoir into the yellow
(middle) reservoir. The yellow
reservoir will expand indicating
transfer of fluid.
Carefully fold back the red
reservoir until it meets the flat face
of the yellow reservoir. Keep
the red reservoir tightly squeezed
while bending the package to
keep material from flowing back.
Squeeze the liquid from the
yellow reservoir into the
green reservoir.
Fully coat the applicator tip
and apply.
Greater Bonding ConfidenceTechnique Guide
How to get
Breakthrough
Performance
Press
1
Press
3
Confirm
5
Spin
4
Apply
6
For maximum effectiveness, follow
the simple steps outlined here to
ensure proper activation.
Adper
TM
Prompt
TM
Self-Etch Adhesive
Available in our innovative, disposable
unit-dose delivery, or vial
delivery system.
Please refer to instructions for
more detailed information, as well as
precautionary and warranty information.
using
Adper
TM
Prompt
TM
Self-Etch Adhesive
3M, ESPE, Adper, Clinpro,
L-Pop and Prompt are
trademarks of 3M or
3M ESPE AG. Used under
license in Canada.
70-2009-3821-8
Dental Products
3M Center
Building 275-2SE-03
St. Paul, MN 55144-1000
USA
1-800-634-2249
©3M 2006.
All rights reserved.
Printed in U.S.A.
10% post-consumer
waste paper
3M Canada
Post Office Box 5757
London, Ontario N6A 4T1
Canada
1-800-265-1840 ext. 6229
3M ESPE Customer Care Center 800-634-2249
www.3MESPE.com/adperprompt
ILLUSTRATED INSIDE:
• How to properly activate the
L-Pop
™
Applicator
• Direct light-cure restoration
• Sealing pits and fi ssures with
the NO-RINSE sealant technique
• Treating hypersensitivity
Adper
™
Prompt
™
L-Pop
™
Self-Etch Adhesive
Proper Activation and Dispensing
Proper activation is the key to ensuring the proper
mix of adhesive and activator … and for achieving
excellent clinical results.
Easy to Activate
• The L-Pop
™
unit-dose applicator allows for easier
flow of material from one chamber to the next.
• When the material moves from the red chamber
to the yellow chamber, the indentation in the yellow
chamber pops up to show that the material has
properly transferred.
Spin or churn applicator
for 5 seconds to mix the
adhesive.
2
Fold
The adhesive’s subtle yellow
tint acts as a visual cue that the
product has been properly mixed.
Activation and Dispensing
Squeeze the material from the
red reservoir into the yellow
(middle) reservoir. The yellow
reservoir will expand indicating
transfer of fluid.
Carefully fold back the red
reservoir until it meets the flat face
of the yellow reservoir. Keep
the red reservoir tightly squeezed
while bending the package to
keep material from flowing back.
Squeeze the liquid from the
yellow reservoir into the
green reservoir.
Fully coat the applicator tip
and apply.
Greater Bonding ConfidenceTechnique Guide
How to get
Breakthrough
Performance
Press
1
Press
3
Confirm
5
Spin
4
Apply
6
For maximum effectiveness, follow
the simple steps outlined here to
ensure proper activation.
Adper
TM
Prompt
TM
Self-Etch Adhesive
Available in our innovative, disposable
unit-dose delivery, or vial
delivery system.
Please refer to instructions for
more detailed information, as well as
precautionary and warranty information.
Adper
™
Prompt
™
Self-Etch Adhesive
Clinpro
™
Sealant
Sealing Pits and Fissures
The NO-RINSE sealant technique saves time and hassle
by eliminating the phosphoric acid-etch and rinse steps.
Briefly, here’s how it’s done:
Preparation
• Thoroughly clean teeth to remove plaque and debris
from enamel surfaces and fissures. Do not use any
cleaning medium that contains oils or fluoride.
• Rinse thoroughly with water, and dry.
• Prepare Adper Prompt adhesive according to the
instructions for Activation and Dispensing found
in this brochure.
Brush Adper Prompt Self-Etch
Adhesive onto surface to be
sealed; scrub for 15 seconds,
applying moderate pressure.
No separate acid-etch step is
needed.
Do not shorten this time.
Proper bonding will not
occur if the solution is simply
applied and dispersed.
1
2
DO NOT RINSE. Instead,
use a gentle stream of air to
thoroughly dry the adhesive
to a thin film. A second layer
is not required for bonding
sealants.
3
Apply a light-cured sealant.
(Note: Adper Prompt Self-Etch
Adhesive is not indicated for
self-cure sealants.)
3M
™
ESPE
™
Clinpro
™
Sealant goes on pink for
easy-to-see application, then
cures to a natural white.
4
Light-cure the sealant and
adhesive together with a
halogen, LED or plasma light
source for the specified time.
Adper
™
Prompt
™
Self-Etch Adhesive
Treating Hypersensitive Root Surfaces
Prepare the surface as
described above.
1
Apply Adper Prompt
adhesive for 15 seconds
using a rubbing motion.
Use a gentle stream of air
to thoroughly dry the
adhesive.
Apply a second layer
(no r
ubbing or waiting time).
Use a gentle stream of air
to thoroughly
dry
the
adhesive
.
Light-cure for
10 seconds
and wipe off air-inhibition layer.
Convenient Application Easier Patient Management Improved Patient Satisfaction
Adper
™
Prompt
™
Self-Etch Adhesive
Direct Light-Cure Restoration
Apply adhesive to the entire surface of the cavity, rubbing in
the solution with moderate finger pressure for 15 seconds.
Do not shorten this time. Proper bonding will not
occur if the solution is simply applied and dispersed.
Use a gentle stream of air to thoroughly dry the adhesive
to a thin film.
Apply a second coat of adhesive.
This coat does not need to be
massaged into the surface.
Again, use a gentle stream of air
to thoroughly dry the adhesive to
a thin film.
Light cure for 10 seconds
(3-second exposure with
a plasma arc lamp).
1
5
2
3 4
2
43
65
Preparation:
• Clean the surface to be treated with a rubber cup and
cleaning paste that is free of fluoride and oil.
• Rinse thoroughly with water spray, and dry.
NOTE: Pooling of the bonding material during application
is to be avoided.
Preparation:
• Clean the unprepared tooth structure with a rubber cup and
cleaning paste
that is free of fluoride and oil.
• Rinse thor
oughly with water spray, and dry.
Adper
™
Prompt
™
Self-Etch Adhesive
Clinpro
™
Sealant
Sealing Pits and Fissures
The NO-RINSE sealant technique saves time and hassle
by eliminating the phosphoric acid-etch and rinse steps.
Briefly, here’s how it’s done:
Preparation
• Thoroughly clean teeth to remove plaque and debris
from enamel surfaces and fissures. Do not use any
cleaning medium that contains oils or fluoride.
• Rinse thoroughly with water, and dry.
• Prepare Adper Prompt adhesive according to the
instructions for Activation and Dispensing found
in this brochure.
Brush Adper Prompt Self-Etch
Adhesive onto surface to be
sealed; scrub for 15 seconds,
applying moderate pressure.
No separate acid-etch step is
needed.
Do not shorten this time.
Proper bonding will not
occur if the solution is simply
applied and dispersed.
1
2
DO NOT RINSE. Instead,
use a gentle stream of air to
thoroughly dry the adhesive
to a thin film. A second layer
is not required for bonding
sealants.
3
Apply a light-cured sealant.
(Note: Adper Prompt Self-Etch
Adhesive is not indicated for
self-cure sealants.)
3M
™
ESPE
™
Clinpro
™
Sealant goes on pink for
easy-to-see application, then
cures to a natural white.
4
Light-cure the sealant and
adhesive together with a
halogen, LED or plasma light
source for the specified time.
Adper
™
Prompt
™
Self-Etch Adhesive
Treating Hypersensitive Root Surfaces
Prepare the surface as
described above.
1
Apply Adper Prompt
adhesive for 15 seconds
using a rubbing motion.
Use a gentle stream of air
to thoroughly dry the
adhesive.
Apply a second layer
(no r
ubbing or waiting time).
Use a gentle stream of air
to thoroughly
dry
the
adhesive
.
Light-cure for
10 seconds
and wipe off air-inhibition layer.
Convenient Application Easier Patient Management Improved Patient Satisfaction
Adper
™
Prompt
™
Self-Etch Adhesive
Direct Light-Cure Restoration
Apply adhesive to the entire surface of the cavity, rubbing in
the solution with moderate finger pressure for 15 seconds.
Do not shorten this time. Proper bonding will not
occur if the solution is simply applied and dispersed.
Use a gentle stream of air to thoroughly dry the adhesive
to a thin film.
Apply a second coat of adhesive.
This coat does not need to be
massaged into the surface.
Again, use a gentle stream of air
to thoroughly dry the adhesive to
a thin film.
Light cure for 10 seconds
(3-second exposure with
a plasma arc lamp).
1
5
2
3 4
2
43
65
Preparation:
• Clean the surface to be treated with a rubber cup and
cleaning paste that is free of fluoride and oil.
• Rinse thoroughly with water spray, and dry.
NOTE: Pooling of the bonding material during application
is to be avoided.
Preparation:
• Clean the unprepared tooth structure with a rubber cup and
cleaning paste
that is free of fluoride and oil.
• Rinse thor
oughly with water spray, and dry.
Adper
™
Prompt
™
Self-Etch Adhesive
Clinpro
™
Sealant
Sealing Pits and Fissures
The NO-RINSE sealant technique saves time and hassle
by eliminating the phosphoric acid-etch and rinse steps.
Briefly, here’s how it’s done:
Preparation
• Thoroughly clean teeth to remove plaque and debris
from enamel surfaces and fissures. Do not use any
cleaning medium that contains oils or fluoride.
• Rinse thoroughly with water, and dry.
• Prepare Adper Prompt adhesive according to the
instructions for Activation and Dispensing found
in this brochure.
Brush Adper Prompt Self-Etch
Adhesive onto surface to be
sealed; scrub for 15 seconds,
applying moderate pressure.
No separate acid-etch step is
needed.
Do not shorten this time.
Proper bonding will not
occur if the solution is simply
applied and dispersed.
1
2
DO NOT RINSE. Instead,
use a gentle stream of air to
thoroughly dry the adhesive
to a thin film. A second layer
is not required for bonding
sealants.
3
Apply a light-cured sealant.
(Note: Adper Prompt Self-Etch
Adhesive is not indicated for
self-cure sealants.)
3M
™
ESPE
™
Clinpro
™
Sealant goes on pink for
easy-to-see application, then
cures to a natural white.
4
Light-cure the sealant and
adhesive together with a
halogen, LED or plasma light
source for the specified time.
Adper
™
Prompt
™
Self-Etch Adhesive
Treating Hypersensitive Root Surfaces
Prepare the surface as
described above.
1
Apply Adper Prompt
adhesive for 15 seconds
using a rubbing motion.
Use a gentle stream of air
to thoroughly dry the
adhesive.
Apply a second layer
(no r
ubbing or waiting time).
Use a gentle stream of air
to thoroughly
dry
the
adhesive
.
Light-cure for
10 seconds
and wipe off air-inhibition layer.
Convenient Application Easier Patient Management Improved Patient Satisfaction
Adper
™
Prompt
™
Self-Etch Adhesive
Direct Light-Cure Restoration
Apply adhesive to the entire surface of the cavity, rubbing in
the solution with moderate finger pressure for 15 seconds.
Do not shorten this time. Proper bonding will not
occur if the solution is simply applied and dispersed.
Use a gentle stream of air to thoroughly dry the adhesive
to a thin film.
Apply a second coat of adhesive.
This coat does not need to be
massaged into the surface.
Again, use a gentle stream of air
to thoroughly dry the adhesive to
a thin film.
Light cure for 10 seconds
(3-second exposure with
a plasma arc lamp).
1
5
2
3 4
2
43
65
Preparation:
• Clean the surface to be treated with a rubber cup and
cleaning paste that is free of fluoride and oil.
• Rinse thoroughly with water spray, and dry.
NOTE: Pooling of the bonding material during application
is to be avoided.
Preparation:
• Clean the unprepared tooth structure with a rubber cup and
cleaning paste
that is free of fluoride and oil.
• Rinse thor
oughly with water spray, and dry.
Adper
™
Prompt
™
Self-Etch Adhesive
Clinpro
™
Sealant
Sealing Pits and Fissures
The NO-RINSE sealant technique saves time and hassle
by eliminating the phosphoric acid-etch and rinse steps.
Briefly, here’s how it’s done:
Preparation
• Thoroughly clean teeth to remove plaque and debris
from enamel surfaces and fissures. Do not use any
cleaning medium that contains oils or fluoride.
• Rinse thoroughly with water, and dry.
• Prepare Adper Prompt adhesive according to the
instructions for Activation and Dispensing found
in this brochure.
Brush Adper Prompt Self-Etch
Adhesive onto surface to be
sealed; scrub for 15 seconds,
applying moderate pressure.
No separate acid-etch step is
needed.
Do not shorten this time.
Proper bonding will not
occur if the solution is simply
applied and dispersed.
1
2
DO NOT RINSE. Instead,
use a gentle stream of air to
thoroughly dry the adhesive
to a thin film. A second layer
is not required for bonding
sealants.
3
Apply a light-cured sealant.
(Note: Adper Prompt Self-Etch
Adhesive is not indicated for
self-cure sealants.)
3M
™
ESPE
™
Clinpro
™
Sealant goes on pink for
easy-to-see application, then
cures to a natural white.
4
Light-cure the sealant and
adhesive together with a
halogen, LED or plasma light
source for the specified time.
Adper
™
Prompt
™
Self-Etch Adhesive
Treating Hypersensitive Root Surfaces
Prepare the surface as
described above.
1
Apply Adper Prompt
adhesive for 15 seconds
using a rubbing motion.
Use a gentle stream of air
to thoroughly dry the
adhesive.
Apply a second layer
(no r
ubbing or waiting time).
Use a gentle stream of air
to thoroughly
dry
the
adhesive
.
Light-cure for
10 seconds
and wipe off air-inhibition layer.
Convenient Application Easier Patient Management Improved Patient Satisfaction
Adper
™
Prompt
™
Self-Etch Adhesive
Direct Light-Cure Restoration
Apply adhesive to the entire surface of the cavity, rubbing in
the solution with moderate finger pressure for 15 seconds.
Do not shorten this time. Proper bonding will not
occur if the solution is simply applied and dispersed.
Use a gentle stream of air to thoroughly dry the adhesive
to a thin film.
Apply a second coat of adhesive.
This coat does not need to be
massaged into the surface.
Again, use a gentle stream of air
to thoroughly dry the adhesive to
a thin film.
Light cure for 10 seconds
(3-second exposure with
a plasma arc lamp).
1
5
2
3 4
2
43
65
Preparation:
• Clean the surface to be treated with a rubber cup and
cleaning paste that is free of fluoride and oil.
• Rinse thoroughly with water spray, and dry.
NOTE: Pooling of the bonding material during application
is to be avoided.
Preparation:
• Clean the unprepared tooth structure with a rubber cup and
cleaning paste
that is free of fluoride and oil.
• Rinse thor
oughly with water spray, and dry.
using
Adper
TM
Prompt
TM
Self-Etch Adhesive
3M, ESPE, Adper, Clinpro,
L-Pop and Prompt are
trademarks of 3M or
3M ESPE AG. Used under
license in Canada.
70-2009-3821-8
Dental Products
3M Center
Building 275-2SE-03
St. Paul, MN 55144-1000
USA
1-800-634-2249
©3M 2006.
All rights reserved.
Printed in U.S.A.
10% post-consumer
waste paper
3M Canada
Post Office Box 5757
London, Ontario N6A 4T1
Canada
1-800-265-1840 ext. 6229
3M ESPE Customer Care Center 800-634-2249
www.3MESPE.com/adperprompt
ILLUSTRATED INSIDE:
• How to properly activate the
L-Pop
™
Applicator
• Direct light-cure restoration
• Sealing pits and fi ssures with
the NO-RINSE sealant technique
• Treating hypersensitivity
Adper
™
Prompt
™
L-Pop
™
Self-Etch Adhesive
Proper Activation and Dispensing
Proper activation is the key to ensuring the proper
mix of adhesive and activator … and for achieving
excellent clinical results.
Easy to Activate
• The L-Pop
™
unit-dose applicator allows for easier
flow of material from one chamber to the next.
• When the material moves from the red chamber
to the yellow chamber, the indentation in the yellow
chamber pops up to show that the material has
properly transferred.
Spin or churn applicator
for 5 seconds to mix the
adhesive.
2
Fold
The adhesive’s subtle yellow
tint acts as a visual cue that the
product has been properly mixed.
Activation and Dispensing
Squeeze the material from the
red reservoir into the yellow
(middle) reservoir. The yellow
reservoir will expand indicating
transfer of fluid.
Carefully fold back the red
reservoir until it meets the flat face
of the yellow reservoir. Keep
the red reservoir tightly squeezed
while bending the package to
keep material from flowing back.
Squeeze the liquid from the
yellow reservoir into the
green reservoir.
Fully coat the applicator tip
and apply.
Greater Bonding ConfidenceTechnique Guide
How to get
Breakthrough
Performance
Press
1
Press
3
Confirm
5
Spin
4
Apply
6
For maximum effectiveness, follow
the simple steps outlined here to
ensure proper activation.
Adper
TM
Prompt
TM
Self-Etch Adhesive
Available in our innovative, disposable
unit-dose delivery, or vial
delivery system.
Please refer to instructions for
more detailed information, as well as
precautionary and warranty information.
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
3M Adper™ Prompt™ L-Pop™ Self-Etch Adhesive Economy Pack,41928 500ct User guide
- Type
- User guide
3M Adper™ Prompt™ L-Pop™ Self-Etch Adhesive Economy Pack,41928 500ct is a dental adhesive system designed for direct light-cure restorations, sealing pits and fissures, and treating hypersensitive root surfaces. It features a unique unit-dose delivery system that ensures proper activation and dispensing of the adhesive and activator. The self-etching formula eliminates the need for a separate acid-etch step, saving time and reducing patient discomfort. The adhesive provides a strong and durable bond to both enamel and dentin, making it ideal for a variety of restorative procedures.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
3M Adper™ Prompt™ L-Pop™ Self-Etch Adhesive Refill User guide
-
-
3M Filtek™ Z250 Universal Restorative User guide
-
-
-
-
-
-
-
Other documents
-
T'nB NEEC011 Datasheet
-
T'nB NEEC005 Datasheet
-
parkell S220 User manual
-
Premier Ziroxide User manual
-
Rust-Oleum RockSolid 306320 User guide
-
Rust-Oleum RockSolid 299745 User manual
-
DAICH DCPR-189-CH User manual
-
Rust-Oleum RockSolid 306325 User manual
-
Gamber-Johnson 7300-0510 Installation guide
-
Rust-Oleum EpoxyShield 292514 User manual
