Telycam Joystick Controller Owner's manual

Brand
Telycam
Model
Joystick Controller
Category
Security cameras
Type
Owner's manual

This manual is also suitable for

TLC-50TC
IP&Serial Joystick Remote Control Keyboard
User Manual
V1.0
J.BC.0205.0158
〓〓〓〓〓〓〓〓 Catalog 〓〓〓〓〓〓〓〓
1
1. Security Guidance........................................................................................................................2
1.1 Cautions........................................................................................................................................2
1.2 Notice......................................... ........ ..........................................................................................2
2. Check Before Using....................................................................................................................3
2.1 Packing List.................................................................................................................................3
2.2 The Wiring...................................... ........ ...................................................................................3
2.3 Bottom Dialing Switch...........................................................................................................3
3. Keyboard Description...............................................................................................................4
3.1 Functional Features..................................................................................................................4
3.2 Technical Specifications.........................................................................................................5
3.3 Product Size.................................................................................................................................5
3.4 Interface Description...............................................................................................................6
3.5 Display Screen Content..................... ........ ........ ..................................................................6
3.6 Button Function.........................................................................................................................7
4. Menu Setting...................................................................................................................................11
4.1 Operating Instructions..........................................................................................................11
4.2 Menu options............................................................................................................................11
5. Wiring diagram............................................................................................................................12
5.1 Connection in network mode.............................................................................................12
5.2 Connection in RS232 mode................................................................................................13
5.3 Connection in RS422 mode................................................................................................14
5.4 Connection in RS485 mode................................................................................................14
5.5 Cascade in RS232, RS422, RS485 mode.....................................................................15
6. WEB Configuration..................................................................................................................17
6.1 Login WEB................................................................................................................................17
6.2 Device Control.........................................................................................................................17
6.3 Network Paramete..................................................................................................................18
6.4 Firmware Upgrade.................................................................................................................18
6.5 Reset Options...........................................................................................................................18
6.6 Account.......................................................................................................................................19
7. Frequently Asked Questions.............................................................................................20
〓〓〓〓〓 1. Security Guidance 〓〓〓〓〓
2
1.1 Cautions:
●Before using the product, please read this safety instruction carefully, operate
strictly in accordance with the instruction manual, and keep this manual properly for
future reference.
●The standard power supply voltage is DC 12V and the rated current is 1A. It is
recommended to use with the power adapter that comes with the product.
●Please place the power cable and control cable in a place where they will not be
trampled on, and protect the cable, especially the connection part must be firm.
●Please use this product within the allowable temperature and humidity range.
Operating temperature: -10℃~ 50℃, humidity ≤ 80%.
●Do not spill liquids, especially corrosive liquids, on this product to prevent
danger.
●Please don't put heavy pressure, violent vibration and immersion during
transportation, storage and installation to avoid damaging the product.
●Please do not disassemble this product without permission, there are no parts
inside the machine that can be repaired by the user, please leave the work to qualified
maintenance personnel.
●Power supply polarity:
1.2 Notice:
█Please refer to the actual product, the user manual is for reference only.
█Please contact our Customer Service Department for the latest procedures and
additional documentation.
█In case of doubt or dispute in the user manual, the final interpretation of the
company shall prevail.
〓〓〓〓〓 2. Check Before Using 〓〓〓〓〓
3
2.1 Packing List
When opening the package, please check and confirm all the accessories that should
be provided.
Control keyboard·········································································· 1PCS
Power Adapter············································································· 1PCS
Power Cord·················································································1PCS
RS232 Cord················································································ 1PCS
User Manual··············································································· 1PCS
Certificate of Conformity································································ 1PCS
Warranty Card············································································· 1PCS
2.2 The Wiring
2.3 Bottom Dialing Switch
Bottom dial control
Mode
SW-1
SW-2
Description
1
*
OFF
ARM Upgrade
Mode
2
*
ON
Normal Working
Mode
SW-1 is reserved, no function defined
〓〓〓〓〓 3. Keyboard Description 〓〓〓〓〓
4
3.1 Functional Features:
★Support network interface, RS232 interface, RS422 interface and RS485
interface for control.
★Supports VISCA Serial, Pelco-P, Pelco-D, VISCA over IP, VISCA TCP, VISCA
UDP, ONVIF, and NDI protocols for control. (NDI protocol is optional.)
★With seven camera shortcut control buttons, to improve the speed of multiple
cameras control switching, convenient and fast.
★Support setting different protocols to control multiple cameras with different
protocols.
★Support one keyboard to control multiple cameras, also support multiple
keyboards to control a camera through the network interface.
★Adapts four-dimensional joystick to enable the control of the video camera PTZ
movement smoothly and flexibly.
★Support to set different levels of operation permission via OSD menu.
★Support button keys backlight, enable users to choose automatic backlight in
low light or dark environment.
★Support set, call and clear presets.
★Support daisy chain function. (Max 7 cameras are available)
★Support camera OSD menu setting.
★Supports standard POE (Power Over Ethe.
★Support 10M, 100M, 1000M adaptive network RJ45 connection.
★Support both Chinese and English menu interface.
〓〓〓〓〓 3. Keyboard Description 〓〓〓〓〓
5
3.2 Technical Specifications：
3.3 Product Size：
Parameters
Control Interface
RJ45
RS232
RS422
RS485
Support Protocols
Upgrade Interface
Display Screen
Working power
Working Temperature
Working Humidity
Storage Temperature
Storage Humidity
Size
Weight
〓〓〓〓〓 3. Keyboard Description 〓〓〓〓〓
6
3.4 Interface Description：
1. Lock hole
5. Network interface
9. Button
2. Upgrade interface
6. Power interface
10. Joystick
3. RS232 interface
7. Indicator light
11. Display screen
4. RS485 interface
8. Adjusting knob
12. Dipswitch
3.5 Display Screen Content：
〓〓〓〓〓 3. Keyboard Description 〓〓〓〓〓
7
3.6 Button Function
3.6.1 Shortcut Selection Area
【CAM1】~【CAM7】Select the corresponding camera.
3.6.2 Adjustment Knob Area, 3A Setting Area
【AE MODE】There is the word “AUTO” next to the button AE MODE. When
the "AUTO" light is on, automatic exposure mode is triggered; when the "AUTO"
light is OFF, the other modes manual exposure, shutter priority, iris priority, bright
priority can be selected, and at this time, the three knobs on the left side of the
keyboard can adjust the shutter, iris, gain, bright and other parameters.
〓〓〓〓〓 3. Keyboard Description 〓〓〓〓〓
8
【WE MODE】There is the word "AUTO" next to the button WE MODE. when
the "AUTO" light is on, it is AUTO and ATW mode; when the "AUTO" light is off,
the manual, indoor and outdoor, Sodium lamps, fluorescent lamps mode can be
selected, then the camera red gain and blue gain can be adjusted through the first two
knobs on the left side of the keyboard.
〓〓〓〓〓 3. Keyboard Description 〓〓〓〓〓
9
【TRIGGER】In Onepush mode ("WB PUSH" light is on), the automatic white
balance is triggered once.
【AF/MF】There is the word "AF" next to the button AF/MF. When the "AF"
light is on, it is the automatic focus mode; when the "AF" light is off, it is the manual
focus mode, which can be adjusted by the third knob on the left side of the keyboard.
Note: When the exposure mode and focus mode are both manual, the 3rd knob
gives priority to adjusting the focus.
【PUSH FOCUS】Triggers autofocus once.
3.6.3 Numeric Button Area
【0】~【9】+【SET】Set the presets.
【0】~【9】+ Short press【CALL/CLEAR】Call the presets.
【0】~【9】+ Long press【CALL/CLEAR】Clear the Presets.
Note: Up to 128 presets can be set and recalled.
3.6.4 Parameter Adjustment Area
【－SHARPNESS＋】 Adjust the sharpness.
【－WDR＋】 Adjust the WDR.
【－CONTRAST＋】 Adjust the contrast.
【－SATURATION＋】 Adjust the saturation.
3.6.5 Other Button Areas
【BLC ON/OFF】Backlight compensation on / off.
【FLICKER】Anti-Flicker switching.
【SEARCH】Search for IP addresses.
【HOME/OK】Return to the original position of the camera.
〓〓〓〓〓 3. Keyboard Description 〓〓〓〓〓
10
【POWER/RESET】Short press to control the camera power, long press to reset
the camera.
【CMENU/KMENU】Short press to open the camera menu, long press to open
the keyboard menu.
3.6.6 Joystick Control
【Up】【Down】【left】【Right】Offset the joystick to control the camera to 4
directions.
【Zoom＋】 Turn the joystick clockwise to zoom in.
【Zoom－】 Turn the joystick counterclockwise to zoom out.
〓〓〓〓〓〓 4. Menu Setting 〓〓〓〓〓〓
11
4.1 Operating Instructions:
1. Long press CMENU/KMENU to open the keyboard menu; Adjust the joystick
Up and Down to view the menu options; Right to enter the next option; Left to return
to the previous option, short press CMENU/KMENU can also return to the previous
option; numeric keys 0~9 can set the corresponding parameters in some options.
2. In the keyboard menu, you need to set the corresponding protocol, address in
order to control the camera properly.
4.2 Menu options:
Camera
setting
Camera
The keyboard can be set with 7 addresses: CAM1~CAM7
Protocol
VISCA Serial, Pelco-P, Pelco-D, VISCA over IP, VISCA TCP,
VISCA UDP, ONVIF, NDI(optional)
IP Addr / Address
Set the camera IP address or camera address.
Port / Baundrate
Set the port or baud rate.
Default port numbers for each IP protocol:
ONVIF: 8000, NDI: 5961, VISCA: 52381
Username
Username setting, default: admin
Password
Password setting, default: admin
Password
setting
New PSD
Set a new keyboard password
Confirm
Reconfirm the new keyboard password
Enable
Switch for keyboard password
Version
Keyboard program version number and update date
System
setting
Language
Chinese/English
Brightness
1~15
BackLight
AUTO/ON/OFF
Screen Prt
10s~180s
DHCP
OFF/ON
Locol IP
192.168.001.180（Can be set）
Mask
255.255.255.000
Gateway
192.168.001.001
PTZ
setting
Pan Reverse
The left and right direction of the keyboard control can be switched.
Tilt Reverse
The up and down direction of the keyboard control can be switched.
Preset PT Spd
Set preset PT speed
Preset Z Spd
Set preset Zoom speed
Foucs Speed
Set focus sensitivity
〓〓〓〓〓〓 5. Wiring diagram 〓〓〓〓〓〓
12
5.1 Connection in network mode:
5.1.1 The keyboard is on the same LAN as the camera: The keyboard connects
to the switch through the network cable, and the camera connects to the switch
through the network cable. In the same LAN, set the same network segment, and set
the corresponding protocol, IP address and port number, you can control the camera
through the keyboard.
5.1.2 The keyboard is directly connected to the camera: The keyboard is
connected to the camera through the network cable, set the same network segment,
and set the corresponding protocol, IP address and port number, you can control the
camera through the keyboard.
〓〓〓〓〓〓 5. Wiring diagram 〓〓〓〓〓〓
13
5.2 Connection in RS232 mode:
The keyboard connects to the camera via RS232 cable, set the corresponding
protocol, address and baud rate, and you can control the camera via the keyboard.
Line Sequence：Using the RS232 connection, pin 1 RXD of the keypad is
connected to the camera input interface TXD, pin 2 TXD of the keypad is connected
to the camera RXD and pin 3 of the keypad is connected to the camera GND. (It is
also possible to use the standard RS232 interface of the control keypad to connect to
the camera.
DB9 Male
(Pin type)
Pin Number
2
3
5
1,4,6
7,8
Signal
Definition
RXD
TXD
GND
Internal
connection
Internal
connection
〓〓〓〓〓〓 5. Wiring diagram 〓〓〓〓〓〓
14
5.3 Connection in RS422 mode:
The keyboard connects to the camera via RS422 cable, set the corresponding
protocol, address and baud rate, and you can control the camera via the keyboard.
Line Sequence：Using the RS422 bus connection, the keyboard pin 1 TXD +
connects to the camera's RXD-, the keyboard pin 2 TXD - connects to the camera's
RXD +, the keyboard pin 3 RXD + connects to the camera's TXD -, the keyboard pin
4 RXD - connects to the camera's TXD+.
Note: Some cameras do not support RS422 control.
5.4 Connection in RS485 mode:
The keyboard connects to the camera via RS485 cable, set the corresponding
protocol, address and baud rate, and you can control the camera via the keyboard.
〓〓〓〓〓〓 5. Wiring diagram 〓〓〓〓〓〓
15
Line Sequence：Using the RS485 bus connection, the keyboard pin 1 TXD +
connected to the camera RXD-, the keyboard pin 2 TXD- connected to the camera
RXD +.
5.5 Cascade in RS232, RS422, RS485 mode：
The keyboard connects the RS232-IN port of camera No. 1 through RS232,
RS422, RS485 lines, and then connects the RS232-IN port of camera No. 2 through
the RS232-OUT port of camera No. 1 with a cascade line, and finally sets the
corresponding protocol, address and baud rate on the keyboard to control camera No.
1 or camera No. 2 through the keyboard.
〓〓〓〓〓〓 5. Wiring diagram 〓〓〓〓〓〓
16
Line Sequence：Using RS232 cascade connection, the output of the keyboard is
connected to the input of camera No. 1, the output of camera No. 1 is connected to the
input of camera No. 2, and so on.
The connection method using RS422 and RS485 cascade is roughly the same as
that of RS232.
〓〓〓〓〓 6. WEB Configuration 〓〓〓〓〓
17
6.1 Login WEB
The keyboard and computer
connected to the same LAN, open the
browser, enter the IP address (default IP
address is 192.168.1.188), enter the login
interface, you can choose the language
(Chinese or English), enter the username
and password to login, as shown on the
right.
(Default username: admin Default password: admin)
After successful login, you will be taken directly to the system configuration screen,
as shown below.
6.2 Device Control
6.2.1 Device Search
Search for IP addresses and protocols of cameras on the same LAN and add them
to the keyboard configuration; you can also add camera IP addresses and protocols
manually.
6.2.2 Device Configuration
Modify and delete the IP address, protocol and port number of the already
configured camera.
〓〓〓〓〓 6. WEB Configuration 〓〓〓〓〓
18
6.3 Ethernet Parameter
Set the network parameters of the
keyboard, including DHCP switch, IP
Address, Netmask, Gateway, DNS,
HTTP Port.
6.4 Firmware Upgrade
Check the keyboard device name and
version information, and also, you can upload
files to upgrade the keyboard system. Please do
not power off during the upgrade process.
6.5 Reset Options
Perform a complete reset or reboot of the
keyboard.
Reset/Reboot: Resets all parameters and
reboots the device.
Reboot: Reboot the device.
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24

Telycam Joystick Controller Owner's manual

Brand
Telycam
Model
Joystick Controller
Category
Security cameras
Type
Owner's manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Other documents