Heng Yu Electronic Manufacturing CK82A User manual

Brand
Heng Yu Electronic Manufacturing
Model
CK82A
Category
Keyboards
Type
User manual

Heng Yu Electronic Manufacturing CK82A is a versatile keyboard that offers both USB and RF connectivity, providing users with flexible options for connecting to their computers. With its plug-and-play functionality for both interfaces, setup is a breeze. The RF connection operates on the 2.4 GHz ISM band and comes pre-paired with the included dongle for immediate use. In case of any RF connectivity issues, a simple re-pairing process can be initiated using the Fn + Esc hotkey combination.

Heng Yu Electronic Manufacturing CK82A is a versatile keyboard that offers both USB and RF connectivity, providing users with flexible options for connecting to their computers. With its plug-and-play functionality for both interfaces, setup is a breeze. The RF connection operates on the 2.4 GHz ISM band and comes pre-paired with the included dongle for immediate use. In case of any RF connectivity issues, a simple re-pairing process can be initiated using the Fn + Esc hotkey combination.

User Menu for CK82A
1、How to use
CK82A is a keyboard which support both USB and RF interface.
For USB interface, just connect cable with micro USB connector and USB type A
connector between keyboard and PC. PC will install HID driver for keyboard
automatically. After installation complete, keyboard is ready to use now.
For RF interface, find the dongle inside the gift box and plug into PC. PC will
install HID driver for dongle automatically. Batteries for keyboard should be installed
before use. After all installation complete, keyboard is ready to use now.
2、Remark
If both USB cable and dongle are plug into PC, USB interface is selected by
keyboard.
RF signal is working at 2.4 GHz ISM band. Keyboard and dongle are set to pair at
factory. If RF interface of keyboard is not working, please check to make sure
batteries are installed correctly. If problem still, please try to re-pair keyboard and
dongle by hot key Fn + Esc while dongle plug into PC. LED for pairing should flash
after hot key pressed. Re-pair complete When LED stops flashing. Keep keyboard
and dongle as close as possible while pairing.
NOTE: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible for compliance could
void the user's authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause
undesired operation.
  • Page 1 1
  • Page 2 2

Heng Yu Electronic Manufacturing CK82A User manual

Brand
Heng Yu Electronic Manufacturing
Model
CK82A
Category
Keyboards
Type
User manual

Heng Yu Electronic Manufacturing CK82A is a versatile keyboard that offers both USB and RF connectivity, providing users with flexible options for connecting to their computers. With its plug-and-play functionality for both interfaces, setup is a breeze. The RF connection operates on the 2.4 GHz ISM band and comes pre-paired with the included dongle for immediate use. In case of any RF connectivity issues, a simple re-pairing process can be initiated using the Fn + Esc hotkey combination.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Other documents