Eaton 9PX EBM 48V RT Installation and User Manual

Brand: Eaton

Model: 9PX EBM 48V RT

Category: Uninterruptible power supplies (UPSs)

Type: Installation and User Manual

ENGLISH

9PX 700 RT

9PX 1000 RT

9PX 1000GRT

9PX 1500 RT

9PX 1500GRT

9PX 2000 RT

9PX 2200 GRT

9PX 3000 RT

9PX 3000 GRT

9PX 3000 GLRT

9PX EBM 36V RT

9PX EBM 48V RT

9PX EBM 72V RT

Installation

and user manual

9PX 1-3 KVA US_EN

Page 2

9PX 1-3 KVA US_EN

SAVE THESE INSTRUCTIONS. This manual contains important instructions

that should be followed during installation and maintenance of the UPS and batteries.

The 9PX models that are covered in this manual are intended for installation

in an environment within 0 to 40°C, free of conductive contaminant.

This equipment has been tested and found to comply with the limits for a Class A digital device,

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against

harmful interference when the equipment is operated in a commercial environment. This equipment

generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance

with the instruction manual, may cause harmful interference to radio communications. Operation of

this equipment in a residential area is likely to cause harmful interference in which case the user will

be required to correct the interference at his own expense.

Special symbols

The following are examples of symbols used on the UPS or accessories to alert you to important

information:

RISK OF ELECTRIC SHOCK - Observe the warning associated with the risk of electric shock symbol.

Important instructions that must always be followed.

Do not discard the UPS or the UPS batteries in the trash.

This product contains sealed lead acid batteries and must be disposed as it's explain in this manual.

For more information, contact your local recycling/reuse or hazardous waste center.

This symbol indicates that you should not discard waste electrical or electronic equipment (WEEE)

in the trash. For proper disposal, contact your local recycling/reuse or hazardous waste center.

Information, advice, help.

Refer to the user manual of UPS accessories.

SAFETY INSTRUCTIONS

Page 3

9PX 1-3 KVA US_EN

ENGLISH

SAFETY INSTRUCTIONS

Safety of persons

• The system has its own power source (the battery). Consequently, the power outlets may be ener-

gized even if the systems is disconnected from the AC power source. Dangerous voltage levels are

presentwithinthesystem.Itshouldbeopenedexclusivelybyqualiedservicepersonnel.

• The system must be properly grounded at all times.

• The battery supplied with the system contains small amounts of toxic materials.

To avoid accidents, the directives listed below must be observed:

- Servicing of batteries should be performed or supervised by personnel knowledgeable about bat-

teries and the required precautions.

- When replacing batteries, replace with the same type and number of batteries or battery packs.

-Donotdisposeofbatteriesinare.Thebatteriesmayexplode.

- Batteries constitute a danger (electrical shock, burns). The short-circuit current may be very high.

• Precautions must be taken for all handling:

- Wear rubber gloves and boots.

- Do not lay tools or metal parts on top of batteries.

- Disconnect charging source prior to connecting or disconnecting battery terminals.

- Determine if battery is inadvertently grounded. If inadvertently grounded, remove source from

ground. Contact with any part of a grounded battery can result in electrical shock. The likelihood

of such shock can be reduced if such grounds are removed during installation and maintenance

(applicable to equipment and remote battery supplies not having a grounded supply circuit).

Product safety

• To connect the UPS, instructions and operation described in the manual must be followed in

the indicated order.

• CAUTION-Toreducetheriskofre,theunitconnectsonlytoacircuitprovided

with 20 or 30 amperes maximum branch circuit overcurrent protection in accordance with the

National Electric Code, ANSI/NFPA 70 (US installations only).

• Check that the indications on the rating plate correspond to your AC powered system and

to the actual electrical consumption of all the equipment to be connected to the system.

• For PLUGGABLE EQUIPMENT, the socket-outlet shall be installed near the equipment and shall

be easily accessible

• Never install the system near liquids or in an excessively damp environment.

• Never let a foreign body penetrate inside the system.

• Never block the ventilation grates of the system.

• Never expose the system to direct sunlight or source of heat.

• If the system must be stored prior to installation, storage must be in a dry place.

• The admissible storage temperature range is -25ºC to +55ºC without batteries, 0°C to 40°C with

batteries.

• The system is not for use in a computer room AS DEFINED IN the standard for the Protection

of Information Technology Equipment, ANSI/NFPA 75 (US installations only).

Contact Eaton resellers to order a special battery kit, if needed to meet the ANSI/NFPA 75

requirement.

Page 4

9PX 1-3 KVA US_EN

SAFETY INSTRUCTIONS

Special precautions

• The unit is heavy: wear safety shoes and use vacuum lifter preferentially for handling operations.

• All handling operations will require at least two people (unpacking, lifting, installation in rack

system).

• Before and after the installation, if the UPS remains de-energized for a long period, the UPS

must be energized for a period of 24 hours, at least once every 6 months (for a normal storage

temperature less than 25°C). This charges the battery, thus avoiding possible irreversible damage.

• During the replacement of the Battery Module, it is imperative to use the same type and number of

element as the original Battery Module provided with the UPS to maintain an identical level of

performance and safety. If there are any questions, don’t hesitate to contact your EATON

representative.

• All repairs and service should be performed by AUTHORIZED SERVICE PERSONNEL ONLY.

There are NO USER SERVICEABLE PARTS inside the UPS.

• For potential safety issue on defective UPS : DISCONNECT INTERNAL BATTERY for storage and

transportation.

Page 5

9PX 1-3 KVA US_EN

ENGLISH

Contents

1. Introduction .........................................................................................

1.1 Environmental protection ............................................................................................... 6

2. Presentation ........................................................................................

2.1 Standard installations ..................................................................................................... 8

2.2 Rear panels ....................................................................................................................9

2.3 Accessories .................................................................................................................10

2.4 Control panel ................................................................................................................ 11

2.5 LCD description ...........................................................................................................12

2.6 Display functions .........................................................................................................13

2.7 User settings ...............................................................................................................13

3. Installation ..........................................................................................

3.1 Inspecting the equipment ...........................................................................................17

3.2 Checking the accessory kit .......................................................................................... 17

3.3 Connecting the internal battery ...................................................................................21

3.4 Connecting the EBM(s) ...............................................................................................22

3.5 Connecting other accessories ....................................................................................22

3.6 Tower installation .........................................................................................................23

3.7 Rack installation ...........................................................................................................24

3.8 UPS connection without HotSwap MBP module ........................................................25

3.9 Connection with a HotSwap MBP module (optional accessory) ........................................ 26

4. Communication ..................................................................................

4.1 Communication ports ..................................................................................................28

4.2 UPS remote control functions .....................................................................................29

4.3 Eaton Intelligent Power Software suite .......................................................................31

5. Operation.............................................................................................

5.1 Start-up and Normal operation ..................................................................................... 32

5.2 Starting the UPS on Battery ......................................................................................... 32

5.3 UPS Shutdown ............................................................................................................32

5.4 Operating modes .........................................................................................................32

5.5 Return of AC Input Power ............................................................................................33

5.6 Setting High Efciency mode ......................................................................................33

5.7 Conguring Bypass settings ........................................................................................33

5.8 Conguring battery settings ........................................................................................34

5.9 Retrieving the Event log ...............................................................................................34

5.10 Retrieving the Fault log ................................................................................................34

6. UPS maintenance ...............................................................................

6.1 Equipment care ............................................................................................................35

6.2 Storing the equipment .................................................................................................35

6.3 When to replace batteries ...........................................................................................35

6.4 Replacing batteries ......................................................................................................36

6.5 Replacing the UPS equipped with a HotSwap MBP .................................................... 38

6.6 Recycling the used equipment ....................................................................................38

7. Troubleshooting ...................................................................................

7.1 Typical alarms and faults ..............................................................................................39

7.2 Silencing the alarm ......................................................................................................40

7.3 Service and support .....................................................................................................40

7.4 CE compliance contact ................................................................................................40

8. Specications ......................................................................................

8.1 Model specications ..................................................................................................41

9. Glossary ........................................................................................... 45

Page 6

9PX 1-3 KVA US_EN

1. Introduction

Thank you for selecting an EATON product to protect your electrical equipment.

The 9PX range has been designed with the utmost care.

We recommend that you take the time to read this manual to take full advantage of the many features

of your UPS (Uninterruptible Power System).

Before installing your 9PX, please read the booklet presenting the safety instructions.

Then follow the indications in this manual.

To discover the entire range of EATON products and the options available for the 9PX range, we invite you

to visit our web site at www.eaton.com/powerquality or contact your EATON representative.

1.1 Environmental protection

EATON has implemented an environmental-protection policy.

Products are developed according to an eco-design approach.

Substances

This product does not contain CFCs, HCFCs or asbestos.

Packing

To improve waste treatment and facilitate recycling, separate the various packing components.

• The cardboard we use comprises over 50% of recycled cardboard.

• Sacks and bags are made of polyethylene.

• Packingmaterialsarerecyclableandbeartheappropriateidenticationsymbol

PET

Materials Abbreviations

Number in

PET

the symbols

Polyethylene terephthalat PET 01

High-density polyethylene HDPE 02

Polyvinyl chloride PVC 03

Low-density polyethylene LDPE 04

Polypropylene PP 05

Polystyrene PS 06

Follow all local regulations for the disposal of packing materials.

End of life

EATON will process products at the end of their service life in compliance with local regulations.

EATON works with companies in charge of collecting and eliminating our products at the end of

their service life.

Product

The product is made up of recyclable materials.

Dismantling and destruction must take place in compliance with all local regulations concerning waste.

At the end of its service life, the product must be transported to a processing center for electrical and

electronic waste.

Battery

The product contains lead-acid batteries that must be processed according to applicable local regulations

concerning batteries.

The battery may be removed to comply with regulations and in view of correct disposal.

Page 7

9PX 1-3 KVA US_EN

ENGLISH

1. Introduction

The Eaton

9PX uninterruptible power system (UPS) protects your sensitive electronic equipment from the

most common power problems, including power failures, power sags, power surges, brownouts, line noise,

high voltage spikes, frequency variations, switching transients, and harmonic distortion.

Power outages can occur when you least expect it and power quality can be erratic. These power problems

have the potential to corrupt critical data, destroy unsaved work sessions, and damage hardware - causing

hours of lost productivity and expensive repairs.

With the Eaton 9PX, you can safely eliminate the effects of power disturbances and guard the integrity

ofyourequipment.Providingoutstandingperformanceandreliability,theEaton9PX’suniquebenets

include:

• True online double-conversion technology with high power density, utility frequency independence, and

generator compatibility.

• ABM

technology that uses advanced battery management to increase battery service life, optimize

recharge time, and provide a warning before the end of useful battery life.

• SelectableHighEfciencymodeofoperation.

• Standard communication options: one RS-232 communication port, one USB communication port, and

relay output contacts.

• Optional connectivity cards with enhanced communication capabilities.

• Extended runtime with up to four Extended Battery Modules (EBMs) per UPS.

• Remote On/Off control through Remote On/Off (ROO) and Remote Power Off (RPO) ports.

• Backed by worldwide agency approvals.

Page 8

9PX 1-3 KVA US_EN

2. Presentation

2.1 Standard installations

Tower installation

Rack installation

Description Weights

(lb/kg)

Dimensions (inch/mm)

D x W x H

9PX700RT 36.4 / 16.5 17.7 x 17.3 x 3.4 / 450 x 440 x 86.5

9PX1000RT 36.4 / 16.5 17.7 x 17.3 x 3.4 / 450 x 440 x 86.5

9PX1000GRT 38.6 / 17.5 17.7 x 17.3 x 3.4 / 450 x 440 x 86.5

9PX1500RT 42.5 / 19.3 17.7 x 17.3 x 3.4 / 450 x 440 x 86.5

9PX1500GRT 41.4 / 18.8 17.7 x 17.3 x 3.4 / 450 x 440 x 86.5

9PX2000RT 61.6 / 27.9 23.8 x 17.3 x 3.4 / 605 x 440 x 86.5

9PX2200GRT 59.7 /

27.1 23.8 x 17.3 x 3.4 / 605 x 440 x 86.5

9PX3000RT 63

/ 28.6 23.8 x 17.3 x 3.4 / 605 x 440 x 86.5

9PX3000GRT 61.2

/ 27.8 23.8 x 17.3 x 3.4 / 605 x 440 x 86.5

9PX3000GLRT 61

/ 27.7 23.8 x 17.3 x 3.4 / 605 x 440 x 86.5

9PXEBM36RT 48.1

/ 21.8 17.7 x 17.3 x 3.4 / 450 x 440 x 86.5

9PXEBM48RT 59.5

/ 27 17.7 x 17.3 x 3.4 / 450 x 440 x 86.5

9PXEBM72RT 86.4

/ 39.2 23.8 x 17.3 x 3.4 / 605 x 440 x 86.5

Page 9

9PX 1-3 KVA US_EN

ENGLISH

2. Presentation

2.2 Rear panels

9PX 700RT / 9PX 1000RT / 9PX 1500RT

1 2 3 4 5 6

9 811 10 7

9PX 2000RT

1 82 43

5 6

9 1011

9PX 1000GRT, 9PX 1500GRT, 9PX 2200GRT &

9PX 3000GRT

1 82 43

9 1011

6 7

9PX 3000RT

(*)

1 82 43

5 6

9 1011

9PX 3000GLRT

1 82 43 5 6 7

9 1011

Socket for connection to AC power

source

Slot for optional communication card

Relay output contact

Connector for additional battery

module

Primary group: outlets for

connection of critical equipment

Group 1: programmable

outlets for connection of equipment

Group 2: programmable

outlets for connection of equipment

Connector for automatic recognition

of an additional battery module

RS232 communication port

USB communication port

Connector for ROO (Remote On/Off)

control and RPO (Remote Power Off)

(*) Primary and Grouped outlets

(

) are protected by 20A

circuit breakers.

Page 10

9PX 1-3 KVA US_EN

2. Presentation

9PX EBM 36V/48V

13 13

1212

Connectors for battery modules

(to the UPS or to the other battery

modules)

Connectors for automatic recognition

of battery modules

9PX EBM 72V

13 13

1212

2.3 Accessories

Part number Description

9PXEBM36RT2U

9PXEBM48RT2U

9PXEBM72RT2U

Extended battery module

9RK Rack kit 9PX

Network-MS Network card

Modbus-MS Modbus and network card

Relay-MS Relay card

BINTSYS Battery Integration System

EBMCBL36 2m cable 36V EBM

EBMCBL48 2m cable 48V EBM

EBMCBL72 2m cable 72V EBM

Page 11

9PX 1-3 KVA US_EN

ENGLISH

2. Presentation

2.4 Control panel

TheUPShasave-buttongraphicalLCD.ItprovidesusefulinformationabouttheUPSitself,loadstatus,

events, measurements and settings.

Online mode

indicator (green)

Fault

indicator (red)

Online mode

100%

19min

1EBM

100%

2.7kW

3.0kVA

Efficiency: 94 %

Escape Up Down Enter On/Off

button

Battery mode

indicator (orange)

Bypass mode

indicator (orange)

The following table shows the indicator status and description:

Indicator Status Description

Green

The UPS is operating normally on Online or on High

Efficiency mode.

Orange

On The UPS is on Battery mode.

Orange

On The UPS is on Bypass mode.

Red

The UPS has an active alarm or fault. See trouble-

shooting on page 39 for additional information.

Page 12

9PX 1-3 KVA US_EN

2. Presentation

2.5 LCD description

After 5 minutes of inactivity, the LCD displays the screen saver.

The LCD backlight automatically dims after 10 minutes of inactivity. Press any button to restore the screen.

Operation status

Load/equipment status

Online mode

100%

19min

1EBM

100%

2.7kW

3.0kVA

Efficiency: 94%

Battery status

Efficiency and load group information

The following table describes the status information provided by the UPS

Note: If other indicator appears, see troubleshooting on page 39 for additional information.

Operation status Cause Description

Standby mode

The UPS is Off, waiting form start-

up command from user.

Equipment is not powered until

button is pressed.

Online mode

The UPS is operating normally. The UPS is powering and protecting

the equipment.

Battery mode

1 beep every 10 seconds

A utility failure has occured and the

UPS is on Battery mode.

The UPS is powering the equipment

with the battery power.

Prepare your equipment for

shutdown.

End of backup time

1 beep every 3 seconds

The UPS is on Battery mode and the

battery is running low.

Low Battery Warning settings:

[Capacity] [0%] ... [100%]

[Runtime] [0mn] ... [60mn]

The alarm triggers when the set

percentage of battery capacity or

remaining back-up time is reached.

High Efficiency mode The UPS is operating on High

Efficiency mode.

The UPS is powering and protecting

the equipment

Bypass mode

An overload or a fault has occurred,

or a command has been received,

and the UPS is in Bypass mode.

Equipment is powered but not

protected by the UPS.

Page 13

9PX 1-3 KVA US_EN

ENGLISH

2.6 Display functions

Press the Enter ( ) button to activate the menu options. Use the two middle buttons ( and ) to scroll

through the menu structure. Press the Enter ( ) button to select an option. Press the button to cancel

or return to the previous menu.

Main menu Submenu Display information or Menu function

Measurements [Load] W VA A pf / [Input/Output] V Hz / [Efficiency] % /

[Battery] % min V n° EBM / [Battery remaining life] months /

[Average power usage] Wh / [Cumulated power] Wh

Control Go to Bypass Transfers the UPS on Bypass mode

Load segments On/Off Commands the load segments

Start battery test Starts a manual battery test

Connectivity test Tests dry contact relay outputs and relay card contacts.

Simulates line failure and battery low

Function reset Clears active fault, power usage, battery remaining life, reset

NMC, Restore factory settings.

Settings Local settings Sets product general parameters

In/Out settings Sets Input and Output parameters

On/Off settings Sets On/Off conditions

Battery settings Sets battery configuration

Com settings Sets communication parameters

Event log Event filter Selects faults, alarms and/or events to display

Event list Displays the events stored

Reset event list Clears events

Fault log Fault list Displays the faults stored

Reset fault list Clears faults

Identification [Product type/model] / [Part/Serial number] / [UPS/NMC firm-

ware] / [Com card IPv4], [Com card IPv6], [Com card MAC]

Registration Links to Eaton registration website

2.7 User settings

The following table displays the options that can be changed by the user.

Submenu Available settings Default settings

Local settings

Language [English] [Français] [Deutsch] [Español]

[Русский] [Português] [Italiano]

[Simplified Chinese] [Japanese]

Menus, status, notices and alarms,

UPS fault, Event Log data and settings

are in all supported languages.

[English]

User selectable when UPS is

powered for the first time.

Date/ time Format:

[International] [US]

[US]

LCD Modify LCD screen brightness and

contrast to be adapted to room light

conditions.

Audible alarm

Mode: [Enabled] [Disabled on battery]

[Always disabled] Enable or disable the

buzzer if an alarm occurs.

[Enabled]

Level: [High] [Low]

[High]

Protected access [Enabled] [Disabled]

Password is: 0577

[Disabled]

2. Presentation

Page 14

9PX 1-3 KVA US_EN

2. Presentation

Submenu Available settings Default settings

In/Out settings

Output voltage [100V] [110V] [120V] [125V]

[200V] [208V] [220V] [230V] [240V]

[120V]

[208V]

Output frequency Mode: [Normal] [Converter] [Marine]

Frequency can be changed in

Frequency [Converter] mode

In [Marine] mode output frequency

follows input frequency

[Normal]

Output mode Mode: [Industrial] [IT] [Custom]

Overload: [Inv>Stop] [Inv>BP]

[Inv>BP>Inv]

Short-circuit: [Inv>Stop] [Inv>BP]

[Inv>BP>Inv]

[IT]

[Inv>BP>Inv]

[Inv>Stop]

Input volt hysteresis Sets input voltage hysteresis

from [1] to |10V]

[10V]

High Efficiency

mode

[Enabled] [Disabled]

Power the output from Bypass for high

efficiency

[Disabled]

Bypass settings

[Volt low]

[Volt high]

[Qualify]

[Hz synch]

[Unsynch]

[80V] LV; [160V] HV;

[144V] LV; [276V] HV;

[In spec];

[5%];

[Half cycle]

Load segments

[Auto start delay]

[Auto shutdown delay]

UPS: [0s]; Group1: [3s];

Group2: [6s]

UPS: [Disabled];

Group1: [Disabled];

Group2: [Disabled]

Overload

prealarm

[10%] … [102%]

Load % when overload alarm occurs

[102%]

On/Off settings

Start/Restart [Cold start] [Auto restart] [Auto start]

[Start on bypass]

[Cold start] [Auto restart] are

Enabled

[Auto start] [Start on bypass]

are Disabled

Forced reboot [Enabled] [Disabled]

[Timer] [10s] … [180s]

When mains recover during a

shutdown sequence:

If set to Enabled, shutdown sequence

will complete and wait 10 seconds

prior to restart,

If set to Disabled, shutdown sequence

will not complete, UPS stays on.

[Enabled]

[10s]

Energy saving [Enabled] [Disabled]

[Timer] [1min] … [15min]

[Level] [100W] … [1000W]

If Enabled, UPS will shut-down after

defined duration. of back-up time, if

load is less than set value.

[Disabled]

[5min]

[100W]

Sleep mode [Enabled] [Disabled]

[Timer] [10min] … [120min]

If Disabled, LCD and communication

will turn OFF immediately after UPS is

OFF.

If Enabled, LCD and communication

stays ON 1h30 min after UPS is OFF.

[Enabled]

[90min]

Site wiring fault [Enabled] [Disabled]

Prevents from starting the UPS in case

of phase vs neutral wires swapping.

[Disabled]

Power Off alert [Enabled] [Disabled]

If Enabled, activates a confirmation

screen that requires user confirmation

after pressing the power button,

before the UPS shutdown occurs.

[Enabled]

Page 15

9PX 1-3 KVA US_EN

ENGLISH

Submenu Available settings Default settings

Battery settings

Automatic battery

test

In ABM cycling mode :

[No test] [Every ABM cycle]

In constant charge mode:

[No test] [Every day] [Every week]

[Every month]

[Every ABM cycle]

[Every week]

Low battery

warning

[Capacity] [0%] … [100%]

[Runtime] [0min] … [60min]

The alarm triggers when the set

percentage of battery capacity or

remaining back-up time is reached.

[0%]

[3min]

Restart bat. level [0%] ... [100%]

If set, automatic restart will occur only

when percentage of battery charge is

reached.

[0%]

Battery charge

mode

[ABM cycling] [Constant charge] [ABM cycling]

External battery [Auto detection] [Manual EBM set.]

[Manual battery set.]

[Auto detection]

Using standard EBM, UPS

detects automatically the

number of EBM connected

Deep Disch.

protect.

[Yes] [No]

If set to Yes, the UPS automatically

prevents battery from deep discharge

by adapting end of back-up time

voltage threshold.

Warranty void if set to No.

[Yes]

Com settings

Input signals [ROO] [RPO] [DB9-4]

Sets Input signals parameters

(function, delay, operation) through

external contact connectors or RS232

port.

ROO port:

- [Function]: [No] [ROO] [RPO]

[Building alarm] [Forced bypass] [On

generator] [Remote shutdown]

- [Delay]: [0s] … [999s]

- [Active]: [Open] [Closed]

RPO port:

- [Function]: [No] [ROO] [RPO]

[Building alarm] [Forced bypass] [On

generator] [Remote shutdown]

- [Delay]: [0s] … [999s]

- [Active]: [Open] [Closed]

DB9-4 port:

- [Function]: [No] [ROO] [RPO]

[Building alarm] [Forced bypass] [On

generator] [Remote shutdown]

- [Delay]: [0s] … [999s]

- [Active]: [High] [Low]:

[No]

[0s]

[Closed]

[No]

[0s]

[Open]

[No]

[0s]

[High]

2. Presentation

Page 16

9PX 1-3 KVA US_EN

2. Presentation

Submenu Available settings Default settings

Com settings

Output signals [Relay] [DB9-1] [DB9-7] [DB9-8]

Sets events or fault that will actuate

Output signal parameters through

external contact connector or RS232

port

[Relay]: [On bat] [Low bat] [Bat fault]

[Bypass] [UPS OK] [Load protected]

[Load powered] [General alarm] [Ext.

charger ON] [OVL pre-alarm]

[DB9-1]: [On bat] [Low bat] [Bat fault]

[Bypass] [UPS OK] [Load protected]

[Load powered] [General alarm] [Ext.

charger ON] [OVL pre-alarm]

[DB9-7]: [On bat] [Low bat] [Bat fault]

[Bypass] [UPS OK] [Load protected]

[Load powered] [General alarm] [Ext.

charger ON] [OVL pre-alarm]

[DB9-8]: [On bat] [Low bat] [Bat fault]

[Bypass] [UPS OK] [Load protected]

[Load powered] [General alarm] [Ext.

charger ON] [OVL pre-alarm]

[Relay] [Bypass]

[DB9-1] [Low bat]

[DB9-7] [UPS OK]

[DB9-8] [On bat]

Remote command [Enabled] [Disabled]

If Enabled, shutdown or restart

commands from software are

authorized.

[Enabled]

Shutdown

commands

[Send CMD] [Output OFF] [OFF delay]

[restart]

Sets events or fault that will actuate

Output signal parameters through

external contact connector or RS232

port

[Send CMD]: [Yes] [No]

[Output OFF]: [No] [UPS] [Group 1]

[Group 2] [Group 1 + Group 2]

[OFF delay]: [0s] …[999s]

[Restart]: [Yes] [No]

Send CMD: [No]

Output OFF: [No]

OFF delay: [0s]

Restart: [Yes]

On battery notice

delay

[0s] ... [99s]

Sets delay before noticing on battery

information to software.

[0s]

General alarm [On battery] [Battery fault]

[Overload pre-alarm] [Internal fault]

[Ambient temp.] [Fan lock]

[Bypass overload] [Current limit]

[Short circuit] [Inverter overload]

[Power overload] [Low battery]

[On bypass] [UPS OK] [Load protected]

[Load powered] [Ext. charger ON]

Defines which event or fault generate

a general alarm through Output signal

screen.

[Internal fault]

Page 17

9PX 1-3 KVA US_EN

ENGLISH

3.1 Inspecting the equipment

If any equipment has been damaged during shipment, keep the shipping cartons and packing materials

forthecarrierorplaceofpurchaseandleaclaimforshippingdamage.Ifyoudiscoverdamageafter

acceptance,leaclaimforconcealeddamage.

Toleaclaimforshippingdamageorconcealeddamage:

1. File with the carrier within 15 days of receipt of the equipment;

2. Send a copy of the damage claim within 15 days to your service representative.

Check the battery recharge date on the shipping carton label. If the date has passed and the

batteries were never recharged, do not use the UPS. Contact your service representative.

3.2 Checking the accessory kit

9PX 700RT / 9PX 1000RT / 9PX 1500RT / 9PX 2000RT / 9PX 3000RT

3. Installation

21 2322

9PX UPS

RS232 communication cable

USB communication cable

Manual CD-ROM

Software leaflet

Safety instructions

Quick start

Mounting kit for 19-inch enclosures

2 supports for tower position

Elements supplied depending on the version or

optional

NMC communication card (optional, standard on

Network Bundle models)

MBP-115 module for 9PX 700RT, 9PX 1000RT and

9PX 1500RT (optional)

MBP-120 module for 9PX 2000RT (optional)

MBP-130 module for 9PX 3000RT(optional)

• Verify that the following additional items are included with the UPS:

Page 18

9PX 1-3 KVA US_EN

3.2 Checking the accessory kit

9PX 1000GRT / 9PX 1500GRT / 9PX 2200GRT / 9PX 3000GRT

3. Installation

21 2322

9PX UPS

Connection cable to AC-power source

2 connection cables for the protected

equipment

RS232 communication cable

USB communication cable

3 cable locking systems

Manual CD-ROM

Software leaflet

Safety instructions

Quick start

Mounting kit for 19-inch enclosures

2 supports for tower position

Elements supplied depending on the version or

optional

NMC communication card (optional, standard on

Network Bundle models)

HotSwap MBP module (optional)

Connection cables between HotSwap MBP

module and UPS

• Verify that the following additional items are included with the UPS:

Page 19

9PX 1-3 KVA US_EN

ENGLISH

3.2 Checking the accessory kit

9PX 3000GLRT

3. Installation

21 2322

9PX UPS

Connection cable to AC-power source

RS232 communication cable

USB communication cable

Cable locking system

Manual CD-ROM

Software leaflet

Safety instructions

Quick start

Mounting kit for 19-inch enclosures

2 supports for tower position

Elements supplied depending on the version or

optional

NMC communication card (optional, standard on

Network Bundle models)

• Verify that the following additional items are included with the UPS:

Page 20

9PX 1-3 KVA US_EN

3. Installation

• If you ordered an optional Extended Battery Module (EBM), verify that the following additional items are

included with the EBM:

Battery power cable with attached battery

detection cable

Stabilizer bracket (4 screws included)

Rack kit for 19-inch enclosures (optional)

EBM Installation manual.

Discard the EBM user’s guide if you are installing the EBM with a new UPS at the same time.

Use the UPS user’s guide to install both the UPS and the EBM.

If you ordered other UPS accessories, refer to specic user manuals to check the packing

contents.

Page is loading ...

Eaton 9PX EBM 48V RT Installation and User Manual

Brand: Eaton

Model: 9PX EBM 48V RT

Category: Uninterruptible power supplies (UPSs)

Type: Installation and User Manual

Download PDF

report

Eaton 9PX EBM 48V RT Installation and User Manual

Eaton 9PX EBM 48V RT Installation and User Manual

Related papers

Other documents