WAGO 4-channel, 24VDC, 0.5A, TYPE N User manual

Brand: WAGO

Model: 4-channel, 24VDC, 0.5A, TYPE N

Type: User manual

Pos: 2 /Dokumentation allgemein/Einband/Einband Handbuch - Deckbl at t oh ne V aria nt enfel d (S ta ndar d) @ 9 \mod_1285229289866_0.docx @ 64941 @ @ 1

Manual

WAGO-I/O-SYSTEM 750

4DO 24V DC 0.5A/ low-side switching

750-516

4-Channel Digital Output Module 24 V DC, Short-

circuit protected, low-

side switching

Version 1.1.0

Pos: 3 /A lle Ser ien ( All ge mein e M odul e)/ Hin weis e z ur D oku men tati on/I mpr ess um für Sta ndar dh and büch er - al lg. A ngabe n, Ansc hrifte n, Telef onn ummer n und E-Mai l-A dresse n @ 3\mod_1219151118203_21.docx @ 21060 @ @ 1

2 WAGO-I/O-SYSTEM 750

750-516 4DO 24V DC 0.5A/ low-side switching

Manual

Version 1.1.0

WAGO Kontakttechnik GmbH & Co. KG

Hansastraße 27

D-32423 Minden

Phone: +49 (0) 571/8 87 – 0

Fax: +49 (0) 571/8 87 – 1 69

E-Mail: [email protected]

Web: http://www.wago.com

Technical Support

Phone: +49 (0) 571/8 87 – 5 55

Fax: +49 (0) 571/8 87 – 85 55

E-Mail: [email protected]

Every conceivable measure has been taken to ensure the accuracy and

completeness of this documentation. However, as errors can never be fully

excluded, we always appreciate any information or suggestions for improving the

documentation.

E-Mail: [email protected]

We wish to point out that the software and hardware terms as well as the

trademarks of companies used and/or mentioned in the present manual are

generally protected by trademark or patent.

=== Ende der Lis te f ür T e xtmar ke Ei nb and _vor ne ===

WAGO-I/O-SYSTEM 750 Table of Contents 3

750-516 4DO 24V DC 0.5A/ low-side switching

Manual

Version 1.1.0

Pos: 5 /D ok ument ati on al lg em ein/V erz eic hni sse /Inh alts ver zei chni s - Ü bersc hrift oG und Ver zeich nis @ 3\mod_1219151230875_21.docx @ 21063 @ @ 1

Table of Contents

1 Notes about this Documentation ................................................................. 5

1.1 Validity of this Documentation ................................................................. 5

1.2 Copyright ................................................................................................... 5

1.3 Symbols ..................................................................................................... 6

1.4 Number Notation ....................................................................................... 8

1.5 Font Conventions ...................................................................................... 8

2 Important Notes ........................................................................................... 9

2.1 Legal Bases ............................................................................................... 9

2.1.1 Subject to Changes ............................................................................... 9

2.1.2 Personnel Qualifications ....................................................................... 9

2.1.3 Use of the WAGO-I/O-SYSTEM 750 in Compliance with Underlying

Provisions ............................................................................................. 9

2.1.4 Technical Condition of Specified Devices ......................................... 10

2.2 Safety Advice (Precautions) .................................................................... 11

3 Device Description ..................................................................................... 13

3.1 View ........................................................................................................ 15

3.2 Connectors ............................................................................................... 16

3.2.1 Data Contacts/Internal Bus ................................................................. 16

3.2.2 Power Jumper Contacts/Field Supply ................................................ 17

3.2.3 CAGE CLAMP

Connectors ............................................................. 19

3.3 Display Elements .................................................................................... 20

3.4 Schematic Diagram ................................................................................. 20

3.5 Technical Data ........................................................................................ 21

3.5.1 Device Data ........................................................................................ 21

3.5.2 Power Supply...................................................................................... 21

3.5.3 Communication .................................................................................. 21

3.5.4 Outputs ............................................................................................... 21

3.5.5 Connection Type ................................................................................ 22

3.5.6 Climatic Environmental Conditions ................................................... 22

3.6 Approvals ................................................................................................ 23

3.7 Standards and Guidelines ........................................................................ 24

4 Process Image ............................................................................................. 25

5 Mounting ..................................................................................................... 26

5.1 Mounting Sequence ................................................................................. 26

5.2 Inserting and Removing Devices ............................................................ 27

5.2.1 Inserting the I/O Module .................................................................... 27

5.2.2 Removing the I/O Module .................................................................. 28

6 Connect Devices ......................................................................................... 29

6.1 Connecting a Conductor to the CAGE CLAMP

................................... 29

6.2 Connection Examples .............................................................................. 30

7 Use in Hazardous Environments .............................................................. 32

7.1 Marking Configuration Examples ........................................................... 33

7.1.1 Marking for Europe According to ATEX and IEC-Ex ...................... 33

7.1.2 Marking for America According to NEC 500 .................................... 38

4 Table of Contents WAGO-I/O-SYSTEM 750

750-516 4DO 24V DC 0.5A/ low-side switching

Manual

Version 1.1.0

7.2 Installation Regulations ........................................................................... 39

7.2.1 Special Conditions for Safe Use (ATEX Certificate TÜV 07 ATEX

554086 X) ........................................................................................... 40

7.2.2 Special Conditions for Safe Use (ATEX Certificate TÜV 12 ATEX

106032 X) ........................................................................................... 41

=== Ende der Lis te f ür T e xtmar ke V erz eic hnis _vor ne == =

WAGO-I/O-SYSTEM 750 Notes about this Documentation 5

750-516 4DO 24V DC 0.5A/ low-side switching

Manual

Version 1.1.0

Pos: 7 /A lle Ser ien ( All ge mein e M odul e)/ Über sc hrif ten für all e Ser ie n/Hi nwei se zur D o kume nt ation /Hi nw eise zu dies er D o kume ntati on - Ü ber schr if t 1 @ 4\ mod_1237987661750_21.docx @ 29029 @ 1 @ 1

1 Notes about this Documentation

Pos: 8 /A lle Ser ien ( All ge mein e M odul e)/ Hin weis e z ur D oku men tati on/H i nweis e/Hi n weis : D okum ent atio n a ufbe wahr e n @ 4 \mod_1237987339812_21.docx @ 29026 @ @ 1

Always retain this documentation!

This documentation is part of the product. Therefore, retain the documentation

during the entire service life of the product. Pass on the documentation to any

subsequent user. In addition, ensure that any supplement to this documentation is

included, if necessary.

Pos: 9 /A lle Ser ien ( All ge mein e M odul e)/ Über sc hrif ten für all e Ser ie n/Hi nwei se zur D o kume nt ation /G ültig kei tsb erei ch - Ü b ersc hrif t 2 @ 1 2\mod_1338912448776_21.docx @ 96469 @ 2 @ 1

1.1 Validity of this Documentation

Pos: 10 /S eri e 7 50 ( WA GO-I/ O-SYST EM )/Hi n weis e zur D okum ent ati on/G ülti gkei ts ber eic h/Gül tig kei tsber ei ch D oku men tat ion Bus kle mme 75 0-xx xx, o hne Var ia nten ang abe @ 14 \mod_1358944037947_21. docx @ 109346 @ @ 1

This documentation is only applicable to the I/O module 750-516

(4DO 24V DC 0.5A/ low-side switching).

Pos: 11 /S eri e 7 50 ( WA GO-I/ O-SYST EM) /Hi n weis e zur D okum ent ati on/Hi nw eise /Ac htu ng: H in weis zur D oku ment ati on B uskl e mmen 750- xxxx @ 4\mod_1237986979656_21.docx @ 29023 @ @ 1

The I/O module 750-516 shall only be installed and operated according to the

instructions in this manual and in the manual for the used fieldbus

coupler/controller.

Consider power layout of the WAGO-I/O-SYSTEM 750!

In addition to these operating instructions, you will also need the manual for the

used fieldbus coupler/controller, which can be downloaded at www.wago.com.

There, you can obtain important information including information on electrical

isolation, system power and supply specifications.

Pos: 12 .1 /All e Seri en (Allgemei ne Module)/Hinweise zur Dokumentati on/Urheberschutz ausführlich @ 4\mod_1235565145234_21.docx @ 27691 @ 2 @ 1

1.2 Copyright

This Manual, including all figures and illustrations, is copyright-protected. Any

further use of this Manual by third parties that violate pertinent copyright

provisions is prohibited. Reproduction, translation, electronic and phototechnical

filing/archiving (e.g., photocopying) as well as any amendments require the

written consent of WAGO Kontakttechnik GmbH & Co. KG, Minden, Germany.

Non-observance will involve the right to assert damage claims.

Pos: 12.2 /Dokumentation allgemein/Gliederungselemente/---Seiten wechs el--- @ 3\mod_1221108045078_0.docx @ 21810 @ @ 1

6 Notes about this Documentation WAGO-I/O-SYSTEM 750

750-516 4DO 24V DC 0.5A/ low-side switching

Manual

Version 1.1.0

Pos: 12.3 /All e Seri en ( All ge meine Mo dul e)/Ü bers chr ift en f ür alle S erie n/Hi nwei se z ur Dok um enta tio n/S ymbol e - Ü bers chr ift 2 @ 1 3\mod_1351068042408_21.docx @ 105270 @ 2 @ 1

1.3 Symbols

Pos: 12 .4.1 /Al le Seri en (All gemei ne Mod ule)/ Wichti ge Erl äuter unge n/Sich erheit s- und so nsti ge H inw eis e/G efa hr/G efa hr: _War nu ng vor P ers onenschäden allgemei n_ - Er läu terung @ 13\mod_1343309450020_21. docx @ 101029 @ @ 1

Personal Injury!

Indicates a high-risk, imminently hazardous situation which, if not avoided, will

result in death or serious injury.

Pos: 12 .4.2 /Al le Seri en (All gemei ne Mod ule)/ Wichti ge Erl äuter unge n/Sich erheit s- und sonsti ge Hinw eise/ Gefa hr/Gef ahr: _ Warnu ng vor Per son enschä den durc h elek trisc hen Str om_ - Erläuterung @ 13\mod_1343309694914_21.docx @ 101030 @ @ 1

Personal Injury Caused by Electric Current!

Indicates a high-risk, imminently hazardous situation which, if not avoided, will

result in death or serious injury.

Pos: 12 .4.3 /Al le Seri en (All gemei ne Mod ule)/ Wichti ge Erl äuter unge n/Sich erheit s- und so nsti ge H inw eis e/W arn ung/ War nung : _ War nu ng vor P erso nens ch äde n all ge mei n_ - Erläuterung @ 13\mod_1343309877041_21.docx @ 101035 @ @ 1

Personal Injury!

Indicates a moderate-risk, potentially hazardous situation which, if not avoided,

could result in death or serious injury.

Pos: 12 .4.4 /Al le Seri en (All gemei ne Mod ule)/ Wichti ge Erl äuter unge n/Sich erheit s- und so nsti ge H inw eis e/V orsic ht /Vor sic ht: _War nu ng vor P ers one nsc häde n al lg emei n_ - Erläuterung @ 13\mod_1343310028762_21.docx @ 101038 @ @ 1

Personal Injury!

Indicates a low-risk, potentially hazardous situation which, if not avoided, may

result in minor or moderate injury.

Pos: 12 .4.5 /Al le Seri en (All ge mei ne Mo dul e)/ Wic htig e Er lä uter ung en/ Sich erh eits- und sonstige Hinweise/Achtung/Achtung: _Warnung vor Sachschäden allgemein_ - Erläuterung @ 13\mod_1343310134623_21.docx @ 101041 @ @ 1

Damage to Property!

Indicates a potentially hazardous situation which, if not avoided, may result in

damage to property.

Pos: 12.4 .6 /Alle S erie n ( Allg emei ne Mod ule) /Wi chti ge Erl äut eru nge n/Si cher hei ts- und sonstige Hinweise/Achtung/Achtung: _Warnung vor Sachschäden durch elektrostatische Aufladung_ - Erläuterung @ 13\mod_1343310227702_21.docx @ 101044 @ @ 1

Damage to Property Caused by Electrostatic Discharge (ESD)!

Indicates a potentially hazardous situation which, if not avoided, may result in

damage to property.

Pos: 12 .4.7 /Al le Seri en (All gemei ne Mod ule)/ Wichti ge Erl äuter unge n/Sich erheit s- und sonstige Hinweise/Hinweis/Hinweis: _Wichtiger Hinweis allge mein _ - Erläuterung @ 13\mod_1343310326906_21.docx @ 101047 @ @ 1

Important Note!

Indicates a potential malfunction which, if not avoided, however, will not result in

damage to property.

Pos: 12 .4.8 /Al le Seri en (All gemei ne Mod ule)/ Wichti ge Erl äuter unge n/Sich erheit s- und so nsti ge H inw eis e/I nfor mat ion/ Inf or matio n: _W eiter e Inf or mati on allg emei n_ - Erl äuter ung @ 13 \mod_1343310439814_21.docx @ 101051 @ @ 1

WAGO-I/O-SYSTEM 750 Notes about this Documentation 7

750-516 4DO 24V DC 0.5A/ low-side switching

Manual

Version 1.1.0

Additional Information:

Refers to additional information which is not an integral part of this

documentation (e.g., the Internet).

Pos: 12.5 /Dokumentation allgemein/Gliederungselemente/---Seiten wechs el--- @ 3\mod_1221108045078_0.docx @ 21810 @ @ 1

8 Notes about this Documentation WAGO-I/O-SYSTEM 750

750-516 4DO 24V DC 0.5A/ low-side switching

Manual

Version 1.1.0

Pos: 12 .6 /All e Seri en (Allg emeine Modul e)/Hi nweis e zur Do kument ation /Zahl ensy steme @ 3\ mod _1221059454015_21.docx @ 21711 @ 2 @ 1

1.4 Number Notation

Table 1: Number Notation

Number code

Example

Note

Decimal

100

Normal notation

Hexadecimal

0x64

C notation

Binary

'100'

'0110.0100'

In quotation marks, nibble separated with

dots (.)

Pos: 12 .7 /All e Seri en (Allg emeine Modul e)/Hi nweis e zur Do kument ation /Schr iftko nventi one n @ 3\mod_1221059521437_21.docx @ 21714 @ 2 @ 1

1.5 Font Conventions

Table 2: Font Conventions

Font type

Indicates

italic

Names of paths and data files are marked in italic-type.

e.g.: C:\Programme\WA GO -I/O-CHECK

Menu items are marked in bold letters.

e.g.: Save

A greater-than sign between two names means the selection of a

menu item from a menu.

e.g.: File > New

Input

Designation of input or optional fields are marked in bold letters,

e.g.: Start of measurement range

“Value”

Input or selective values are marked in inverted commas.

e.g.: Enter the value “4 mA” under Start of measurement range.

[Button]

Pushbuttons in dialog boxes are marked with bold letters in square

brackets.

e.g.: [Input]

[Key]

Keys are marked with bold letters in square brackets.

e.g.: [F5]

Pos: 13 /Doku ment ation all gemei n/Gli eder ungsel eme nte/---Seit en wechs el--- @ 3\ mod_1221108045078_0.docx @ 21810 @ @ 1

WAGO-I/O-SYSTEM 750 Important Notes 9

750-516 4DO 24V DC 0.5A/ low-side switching

Manual

Version 1.1.0

Pos: 14 /Alle Ser ien (Al lge meine Mo dule)/ Über schrif ten für alle Ser ien/ Wichti ge Erlä uteru ngen/ Wich tige Er läuter ungen - Übersc hrift 1 @ 4\mod_1241428899156_21.docx @ 32170 @ 1 @ 1

2 Important Notes

Pos: 15 .1 /All e Ser i en (Al lg emei ne D oku men te) ( Al lge mei ne M od ule)/ Wic htig e Er lä uter ung en/ Einl eit ung Wic htig e Er lä uter ung en @ 3\ mod_1221059818031_21.docx @ 21717 @ @ 1

This section includes an overall summary of the most important safety

requirements and notes that are mentioned in each individual section. To protect

your health and prevent damage to devices as well, it is imperative to read and

carefully follow the safety guidelines.

Pos: 15 .2 /All e Seri en (Allg emeine Modul e)/Ü berschr ifte n für alle S erie n/Wich tige Er läuter u ngenR ec htlic he Gr undl ag en - Üb ersc hrift 2 @ 3\ mod_1221060626343_21.docx @ 21726 @ 2 @ 1

2.1 Legal Bases

Pos: 15.3 /All e Serien (Allgemeine Dokumente) (Allgemei ne Module)/Wichtige Erläut erungen/Änderungsvorbehalt - Übers chri ft 3 un d In halt @ 3\mod_1221060036484_21.docx @ 21720 @ 3 @ 1

2.1.1 Subject to Changes

WAGO Kontakttechnik GmbH & Co. KG reserves the right to provide for any

alterations or modifications that serve to increase the efficiency of technical

progress. WAGO Kontakttechnik GmbH & Co. KG owns all rights arising from

the granting of patents or from the legal protection of utility patents. Third-party

products are always mentioned without any reference to patent rights. Thus, the

existence of such rights cannot be excluded.

Pos: 15.4 /Serie 750 (WAGO-I/O-SYST EM)/ Wicht ige Erl äuter unge n/Pers onalq uali fikati onPer sonal quali fikat ion 750- xxxx - Ü bersc hrift 3 u nd Inhal t @ 3\mod_1224061208046_21.docx @ 24063 @ 3 @ 1

2.1.2 Personnel Qualifications

All sequences implemented on WAGO-I/O-SYSTEM 750 devices may only be

carried out by electrical specialists with sufficient knowledge in automation. The

specialists must be familiar with the current norms and guidelines for the devices

and automated environments.

All changes to the coupler or controller should always be carried out by qualified

personnel with sufficient skills in PLC programming.

Pos: 15.5 /Serie 750 (WAGO-I/O-SYSTEM)/Wichtige Erläuterungen/Bestimmungsgemäße VerwendungBestimmungsgemäße Verwendung 750-xxxx - Üb ersc hrif t 3 un d In hal t @ 3 \mod_1224064151234_21. docx @ 24070 @ 3 @ 1

2.1.3 Use of the WAGO-I/O-SYSTEM 750 in Compliance with

Underlying Provisions

Fieldbus couplers, fieldbus controllers and I/O modules found in the modular

WAGO-I/O-SYSTEM 750 receive digital and analog signals from sensors and

transmit them to actuators or higher-level control systems. Using programmable

controllers, the signals can also be (pre-) processed.

The devices have been developed for use in an environment that meets the IP20

protection class criteria. Protection against finger injury and solid impurities up to

12.5 mm diameter is assured; protection against water damage is not ensured.

Unless otherwise specified, operation of the devices in wet and dusty

environments is prohibited.

Operating the WAGO-I/O-SYSTEM 750 devices in home applications without

further measures is only permitted if they meet the emission limits (emissions of

interference) according to EN 61000-6-3. You will find the relevant information

in the section “Device Description” > “Standards and Guidelines” in the manual

for the used fieldbus coupler/controller.

10 Important Notes WAGO-I/O-SYSTEM 750

750-516 4DO 24V DC 0.5A/ low-side switching

Manual

Version 1.1.0

Appropriate housing (per 94/9/EG) is required when operating the WAGO-I/O-

SYSTEM 750 in hazardous environments. Please note that a prototype test

certificate must be obtained that confirms the correct installation of the system in

a housing or switch cabinet.

Pos: 15.6 /All e Seri en ( All ge meine Do kum ente) ( All ge meine Mo dule) /Wi cht ige Erl äut eru nge n/T echni sc her Zus tan d d er G erä te - Ü bersc hrift 3 un d Inhal t @ 3\mod_1221060446109_21.docx @ 21723 @ 3 @ 1

2.1.4 Technical Condition of Specified Devices

The devices to be supplied ex works are equipped with hardware and software

configurations, which meet the individual application requirements. WAGO

Kontakttechnik GmbH & Co. KG will be exempted from any liability in case of

changes in hardware or software as well as to non-compliant usage of devices.

Please send your request for modified and new hardware or software

configurations directly to WAGO Kontakttechnik GmbH & Co. KG.

Pos: 15.7 /Dokumentation allgemein/Gliederungselemente/---Seiten wechs el--- @ 3\mod_1221108045078_0.docx @ 21810 @ @ 1

WAGO-I/O-SYSTEM 750 Important Notes 11

750-516 4DO 24V DC 0.5A/ low-side switching

Manual

Version 1.1.0

Pos: 15 .8 /All e Seri en (Allg emeine Modul e)/Ü berschr ifte n für alle S erie n/Wich tige Er läuter ung enSic herhei tshi nweis e - Über schr ift 2 @ 6\mod_1260180299987_21.docx @ 46724 @ 2 @ 1

2.2 Safety Advice (Precautions)

Pos: 15.9 /All e Seri en ( All ge meine Do kum ente) ( All ge meine Mo dule) /Wi cht ige Erl äut eru nge n/Si cher hei ts hin weis e/Ei nl eitu ng Sich erh eitshi nweis e Hard ware @ 6\mod_1260180170493_21.docx @ 46720 @ @ 1

For installing and operating purposes of the relevant device to your system the

following safety precautions shall be observed:

Pos: 15.10.1 /Alle Serien (Allgemeine Dokumente) (Allgemeine M odule)/Wichtige Erläuter ungen/Sicherhei tshi nw eise /Gef ahr /G efahr : N ich t an Ger äte n un ter Spa nnu ng ar bei te n! @ 6\mod_1260180365327_21.docx @ 46727 @ @ 1

Do not work on devices while energized!

All power sources to the device shall be switched off prior to performing any

installation, repair or maintenance work.

Pos: 15.1 0. 2 /S erie 750 ( W AGO -I/O-SY ST EM) /Wic htig e Er l äuter ung en /Sic her hei ts- un d s onsti ge H in wei se/G ef ahr/ Gefa hr: Ei nbau 07 50- xxxx nur in Geh äusen, S chrä nken oder ele ktrisc hen Betr iebsr äume n! @ 6\mod_1260180556692_21.docx @ 46731 @ @ 1

Install the device only in appropriate housings, cabinets or in electrical

operation rooms!

The WAGO-I/O-SYSTEM 750 and its components are an open system. As such,

install the system and its components exclusively in appropriate housings,

cabinets or in electrical operation rooms. Allow access to such equipment and

fixtures to authorized, qualified staff only by means of specific keys or tools.

Pos: 15.1 0. 3 /Al le S eri en ( Allg em ein e Do ku ment e) (Al lg em eine M o dul e)/ Wich tig e Erl äuter u ngen /Sic h erhei ts hinw eise /G efahr /G efahr : U nfal l verh ütung sv orsc hri ft en b each ten! @ 6\mod_1260180657000_21.docx @ 46735 @ @ 1

Pos: 15.1 0. 4 /Al le S eri en ( Allg em ein e Do ku ment e) (Al lg em eine M o dul e)/ Wich tig e Erl äuter u ngen /Sic h erhei ts hinw eise /G efahr /G efahr : A uf normg er echt e n Ansc hlu ss ac hten! @ 6\mod_1260180753479_21.docx @ 46739 @ @ 1

Pos: 15.1 1. 1 /Al le S eri en ( Allg em ein e Do ku ment e) (Al lg em eine M o dul e)/ Wich tig e Erl äuter ungen /Sic herhei tshin weise /Acht ung/A chtu ng: Defe kte od er besc hädigt e Ger äte austa usch en! @ 6\mod_1260180857358_21.docx @ 46743 @ @ 1

Replace defective or damaged devices!

Replace defective or damaged device/module (e.g., in the event of deformed

contacts), since the long-term functionality of device/module involved can no

longer be ensured.

Pos: 15.1 1. 2 /Al le S eri en ( Allg em ein e Do ku ment e) (Al lg em eine M o dul e)/ Wich tig e Erl äuter u ngen /Sic h erhei ts hinw eise /Ac htu ng/A cht ung : G erät e vor kriec hen den und i sol ier e nden Sto ffen sch ütz en! @ 6\ mod_1260181036216_21.docx @ 46747 @ @ 1

Protect the components against materials having seeping and insulating

properties!

The components are not resistant to materials having seeping and insulating

properties such as: aerosols, silicones and triglycerides (found in some hand

creams). If you cannot exclude that such materials will appear in the component

environment, then install the components in an enclosure being resistant to the

above-mentioned materials. Clean tools and materials are imperative for handling

devices/modules.

Pos: 15.1 1. 3 /Al le S eri en ( Allg em ein e Do ku ment e) (Al lg em eine M o dul e)/ Wich tig e Erl äuter u ngen /Sic h erhei ts hinw eise /Ac htu ng/A cht ung : Rei nig ung nur mi t zul äss ig en M at erial ien! @ 6\mod_1260181203293_21.docx @ 46751 @ @ 1

Clean only with permitted materials!

Clean soiled contacts using oil-free compressed air or with ethyl alcohol and

leather cloths.

Pos: 15.1 1. 4 /Al le S eri en ( Allg em ein e Do ku ment e) (Al lg em eine M o dul e)/ Wich tig e Erl äuter u ngen /Sic h erhei ts hinw eise /Ac htu ng/A cht ung : K ein K ont a ktspra y verw end en! @ 6\ mod_1260181290808_21.docx @ 46755 @ @ 1

12 Important Notes WAGO-I/O-SYSTEM 750

750-516 4DO 24V DC 0.5A/ low-side switching

Manual

Version 1.1.0

Do not use any contact spray!

Do not use any contact spray. The spray may impair contact area functionality in

connection with contamination.

Pos: 15.1 1. 5 /Al le S eri en ( Allg em ein e Do ku ment e) (Al lg em eine M o dul e)/ Wich tig e Erl äuter u ngen /Sic h erhei ts hinw eise /Ac htu ng/A cht ung : V erpol ung ver mei de n! @ 6\mod_1260184045744_21.docx @ 46767 @ @ 1

Do not reverse the polarity of connection lines!

Avoid reverse polarity of data and power supply lines, as this may damage the

devices involved.

Pos: 15.1 1. 6 /Al le S eri en ( Allg em ein e Do ku ment e) (Al lg em eine M o dul e)/ Wich tig e Erl äuter u ngen /Sic h erhei ts hinw eise /Ac htu ng/A cht ung : Elektr ostat isch e Entla dung v ermeid en! @ 6\mod_1260181364729_21.docx @ 46759 @ @ 1

Avoid electrostatic discharge!

The devices are equipped with electronic components that may be destroyed by

electrostatic discharge when touched. Please observe the safety precautions

against electrostatic discharge per DIN EN 61340-5-1/-3. When handling the

devices, please ensure that environmental factors (personnel, work space and

packaging) are properly grounded.

Pos: 16 /Doku ment ation all gemei n/Gli eder ungsel eme nte/---Seit en wechs el--- @ 3\mod_1221108045078_0.docx @ 21810 @ @ 1

WAGO-I/O-SYSTEM 750 Device Description 13

750-516 4DO 24V DC 0.5A/ low-side switching

Manual

Version 1.1.0

Pos: 17 /A ll e Ser ien (Al lg emei ne M odul e)/Üb erschr ifte n für alle S erie n/Gerä tebes chrei bung /Gerä tebesc hreib ung - Üb ersc hrift 1 @ 3\ mod_1233756084656_21.docx @ 27096 @ 1 @ 1

3 Device Description

Pos: 18.1 .1 /Ser ie 7 50 ( WAG O-I/ O-SYST EM )/G eräte bes chr eibu ng/Ei nlei tu ng/A nw endung /D O/An wen dung 750- x5xx DO @ 3\mod_1233764594468_21.docx @ 27120 @ @ 1

The 750-516 Digital Output Module transmits binary control signals from the

automation device to the connected actuators (e.g., solenoid valves, contactors,

transmitters, relays or other electrical loads).

Pos: 18.1 .2 /Ser ie 7 50 ( WAG O-I/ O-SYST EM )/G eräte bes chr eibu ng/Ei nlei tu ng/I/ O-B esc hrei bung /DO /I/O- Besc hrei bung 75 0-0516 4 D O 2-Leit er ( DO und 24 V) @ 5\mod_1246612016609_21.docx @ 36569 @ @ 1

</dg_

The I/O module has 4 output channels, providing a direct connection to 2-wire

actuators.

The actuators are connected to the following CAGE CLAMP

terminals: DO 1 or

DO 2, DO 3, DO 4 and 24 V.

Pos: 18.1 .3 /Ser ie 7 50 ( WAG O-I/ O-SYST EM )/G eräte bes chr eibu ng/Ei nlei tu ng/I/ O-B esc hrei bung/DO /I/O- Besc hrei bung 75 0-516 Pot ential ver vielfäl tig ungskl emme @ 2 0\mod_1413544885133_21.docx @ 166078 @ @ 1

</dg_

The 24 V and 0 V potentials can be wired to the 750-516 I/O module directly for

up to 2 actuators. A suitable field side connection module (e.g., 750-614) must be

also be used to connect other actuators.

Pos: 18.1 .4 /Ser ie 7 50 ( WAG O-I/ O-SYST EM )/G eräte bes chr eibu ng/Ei nlei tu ng/I/ O-B esc hrei bung /All ge mein /V er weis a uf Kapi tel " A nsc hlüss e" @ 8\ mod_1276775378035_21.docx @ 57956 @ @ 1

The assignment of the connections is described in the “Connectors” section.

Pos: 18.1 .5 /Ser ie 7 50 ( WAG O-I/ O-SYST EM )/G eräte bes chr eibu ng/Ei nlei tu ng/I/ O-B esc hrei bung /All ge mein /V er weis a uf Kapi tel " G erät e an schl ieß en" > " Ansc hlussb eispi el(e) " @ 5\mod_1246015203281_21.docx @ 36298 @ @ 1

Connection examples are shown in section “Connecting Devices” > … >

“Connection Example(s)”.

Pos: 18.1 .6 /Ser ie 7 50 ( WAG O-I/ O-SYSTEM)/Wichtige Erläuterungen/Sicherheits- und sonstige Hinweise/Achtung/Achtung: DO Induktionss pannungsbegrenzung Elektronik @ 3\mod_1233815757507_21.docx @ 27153 @ @ 1

Limit all induced voltage!

The electronic components of the I/O module can be damaged by the induced

voltage produced when inductive loads are de-activated.

An appropriate protection circuit, e.g., a recovery diode, must be installed in

parallel to the load to limit this induced voltage.

Pos: 18.1 .7 /Ser ie 7 50 ( WAG O-I/ O-SYST EM )/G eräte bes chr eibu ng/Ei nlei tu ng/I/ O-B esc hrei bung /DO /I/O- Besc hrei bung 75 0-05xx DO kurzsc hlussfest @ 3\mod_1233817429086_21.docx @ 27167 @ @ 1

The output channels are electrically short-circuit-protected.

Pos: 18.1 .8 /Ser ie 7 50 ( WAG O-I/ O-SYST EM )/G eräte bes chr eibu ng/Ei nlei tu ng/I/ O-B esc hrei bung /DO /I/O- Besc hrei bung 75 0-0516 D O LSS / nega tivsc halt end (0 V) @ 20\mod_1413469240978_21.docx @ 165932 @ @ 1

The I/O module outputs provide negative switching. If the signal status of an

output channel is at "1" the 0V potential for field power will be switched to the

appropriate output connection.

Pos: 18.1 .9 /Ser ie 7 50 ( WAG O-I/ O-SYSTEM)/Wichtige Erläuterungen/Sicherheits- und sonstige Hinweis e/Achtung/Achtung: DO Überlastsc hutz - Einpeiseklemme mit Sicherung @ 3\mod_1233814881117_21. docx @ 27150 @ @ 1

Provide for overload protection!

Overloading can damage the electronic components of the I/O module.

A fused supply module (750-601) must be installed upstream of the I/O module to

protect it against overloading!

Pos: 18.1 .1 0 /S erie 750 ( W AGO -I/O-SY ST EM) /Wic htig e Er l äuter ung en /Sic her hei ts- un d s onsti ge H in wei se/A cht ung /Ac htung : Maxi mal er Str om Leis tung sko nta kte 10 A @ 3 \mod_1226499143500_21. docx @ 25029 @ @ 1

Do not exceed maximum current via power jumper contacts!

The maximum current to flow through the power jumper contacts is 10 A.

Greater currents can damage the contacts.

When configuring your system, ensure that this current is not exceeded. If

exceeded, insert an additional supply module.

Pos: 18.1 .1 1 /S erie 750 ( W AGO -I/O-SY ST EM)/ Gerät ebe schr eib ung/ Einl eit ung/ LED -Anzeige/LED Zus tand Signal @ 3\mod_1233755258578_21.docx @ 27087 @ @ 1

A green LED indicates the switched status of each channel.

Pos: 18.1 .1 2 /S erie 750 ( W AGO -I/O-SY ST EM)/ Gerät ebe schr eib ung/ Einl eit ung/ LED -Anz eige /V erwei s a uf K api tel " A nzeig eel e ment e" @ 5 \mod_1246010525000_21.docx @ 36194 @ @ 1

14 Device Description WAGO-I/O-SYSTEM 750

750-516 4DO 24V DC 0.5A/ low-side switching

Manual

Version 1.1.0

The meaning of the LEDs is described in the “Display Elements” section.

Pos: 18.1 .1 3 /S erie 750 ( W AGO -I/O-SY STEM )/Ger ätebe schr eibung /Einl eitung /V ersorg ung/V ersor gung 24 V, 0 V über Lei stu ngskont akte St and ard @ 3\mod_1226498974531_21.docx @ 25020 @ @ 1

The I/O module receives the 24 V voltage supply for the field level from an

upstream I/O module or from the fieldbus coupler/controller via two blade-formed

power jumper contacts. It then provides these potentials to subsequent I/O

modules via two spring-formed power jumper contacts.

Pos: 18.1 .1 4 /S erie 750 ( W AGO -I/O-SY ST EM) /Wic htig e Er l äuter ung en /Sic her hei ts- un d s onsti ge H in wei se/A cht ung /Ac htung : Maxi mal er Str om Leis tung sko nta kte 10 A @ 3 \mod_1226499143500_21. docx @ 25029 @ @ 1

Do not exceed maximum current via power jumper contacts!

The maximum current to flow through the power jumper contacts is 10 A.

Greater currents can damage the contacts.

When configuring your system, ensure that this current is not exceeded. If

exceeded, insert an additional supply module.

Pos: 18.1 .1 5 /S erie 750 ( W AGO -I/O-SY ST EM) /Wic htig e Er l äuter ung en /Sic her hei ts- un d s onsti ge H in wei se/H in weis /Hi nwei s: P ot ential ei nsp eis ekle mm e für Er de eins etz en! (kei ne LK f ür Er de) @ 3\mod_1226499037468_21.docx @ 25023 @ @ 1

Use supply modules for ground (earth)!

The I/O module has no power jumper contacts for receiving and transmitting the

earth potential. Use a supply module when an earth potential is needed for the

subsequent I/O modules.

Pos: 18.1 .1 6 /S erie 750 ( W AGO -I/O-SY ST EM) /Ger äte bes chr eib ung/ Einl eit ung/ V ersor gu ng/G al vanisc h e Tre nnu ng F eld/ S yste m @ 3\mod_1233756478750_21.docx @ 27102 @ @ 1

The field voltage and the system voltage are electrically isolated from each other.

Pos: 18.1 .1 7 /S erie 750 ( W AGO -I/O-SY ST EM) /Ger äte bes chr eib ung/ Einl eit ung/ V ersor gu ng/A nor dnu ng u nter Ber üc ksic htig ung der L eist ungs kon tak te b elie big @ 3 \mod_1233756233468_21.doc x @ 27099 @ @ 1

With consideration of the power jumper contacts, the individual modules can be

arranged in any combination when configuring the fieldbus node. An arrangement

in groups within the group of potentials is not necessary.

Pos: 18.1 .1 8 /S erie 750 ( W AGO -I/O-SY STEM )/Ger ätebe schr eibung /Einl eitung /Ein satzb ereic h/Ein satzb ereic h 750- xxxx all e Ko ppler /C ontr oll er o hne Ei nsc hrä nkung @ 3 \mod_1232541691906_21.docx @ 26522 @ @ 1

The I/O module 750-516 can be used with all fieldbus couplers/controllers of the

WAGO-I/O-SYSTEM 750.

Pos: 18.2 /Dokumentation allgemein/Gliederungselemente/---Seiten wechs el--- @ 3\mod_1221108045078_0.docx @ 21810 @ @ 1

WAGO-I/O-SYSTEM 750 Device Description 15

750-516 4DO 24V DC 0.5A/ low-side switching

Manual

Version 1.1.0

Pos: 18.3 /All e Seri en ( All ge meine Mo dul e)/Ü bers chr ift en für al le Seri en/Ger äteb eschr eibu ng/Ans icht - Ü ber schri ft 2 @ 4\mod_1240984217343_21.docx @ 31958 @ 2 @ 1

3.1 View

Pos: 18.4 /Serie 750 (WAGO-I/O-SYST EM) /G erät eb esc hrei bung /Ans ic ht/D ig itala usg ang skle mm en/A nsic ht 750- 051 6 - Abb. @ 11\mod_1322123675546_21.docx @ 83610 @ @ 1

Figure 1: View

Pos: 18.5 /Serie 750 (WAGO-I/O-SYST EM) /G erät eb esc hrei bung /Ans ic ht/A nsi cht C ag eCl amp® _Legende mit LEDs @ 15\ mod_1370867188922_21.docx @ 122225 @ @ 1

Table 3: Legend for Figure “View”

Pos.

Description

Details See Section

Marking possibility with Mini-

WSB

---

Status LEDs

“Device Description” > “Display Elements”

Data contacts

“Device Description” > “Connectors”

CAGE CLAMP

connectors

“Device Description” > “Connectors”

Power jumper contacts

“Device Description” > “Connectors”

Release tab

“Mounting” > “Inserting and Removing

Devices”

Pos: 18 .6 /Dokumentation allgemein/Gliederungselemente/---Seite nwec hsel--- @ 3\ mod_1221108045078_0.docx @ 21810 @ @ 1

16 Device Description WAGO-I/O-SYSTEM 750

750-516 4DO 24V DC 0.5A/ low-side switching

Manual

Version 1.1.0

Pos: 18.7 /All e Seri en ( All ge meine Mo dul e)/Ü bers chr ift en f ür alle S erie n/Ger äte bes chr eib ung /Ans chl üss e - Üb ersc hrift 2 @ 4\ mod_1240984262656_21.doc x @ 319 61 @ 2 @ 1

3.2 Connectors

Pos: 18.8 /Serie 750 (WAGO-I/O-SYST EM) /Ger äte besc hrei bu ng/A nschl üss e/Da ten kon takt e/Kl em menbus - Ü bersc hrift 3 @ 6\ mod_1256294684083_21.doc x @ 43660 @ 3 @ 1

3.2.1 Data Contacts/Internal Bus

Pos: 18 .9.1 /S erie 750 (WAGO-I/ O-SYSTEM)/Gerätebeschrei bung/Anschlüsse/Datenkontakte - F eld bus koppl er/-c ontr oll er, Ab bild ung und Bes chr eibu ng @ 3\ mod_1231771259187_21.docx @ 26002 @ @ 1

Communication between the fieldbus coupler/controller and the I/O modules as

well as the system supply of the I/O modules is carried out via the internal bus. It

is comprised of 6 data contacts, which are available as self-cleaning gold spring

contacts.

Figure 2: Data Contacts

Pos: 18.9 .2 /Ser ie 7 50 ( WAG O-I/ O-SYSTEM)/Wichtige Erläuterungen/Sicherheits- u nd s onst ige Hi nwei se/ Ach tung /A chtu ng: Bus kle mm en ni cht auf Gol df eder kon takt e leg en! @ 7\mod_1266318463636_21.docx @ 50695 @ @ 1

Do not place the I/O modules on the gold spring contacts!

Do not place the I/O modules on the gold spring contacts in order to avoid soiling

or scratching!

Pos: 18.9 .3 /Ser ie 7 50 ( WAG O-I/ O-SYSTEM)/Wichtige Erläuterungen/Sicherheits- und sonstige Hinweise/Achtung/Achtung: ESD - A uf gut e Erdung der Umg ebung achten! @ 7\mod_1266318538667_21.docx @ 50708 @ @ 1

Ensure that the environment is well grounded!

The devices are equipped with electronic components that may be destroyed by

electrostatic discharge. When handling the devices, ensure that the environment

(persons, workplace and packing) is well grounded. Avoid touching conductive

components, e.g. data contacts.

Pos: 18.1 0 /D ok um entati o n allg em ein/ Gli eder ung sel eme nte/---S eit enw echs el--- @ 3\ mod_1221108045078_0.docx @ 21810 @ @ 1

WAGO-I/O-SYSTEM 750 Device Description 17

750-516 4DO 24V DC 0.5A/ low-side switching

Manual

Version 1.1.0

Pos: 18.1 1 / Ser ie 7 50 ( WAG O-I/ O-SYST EM) /Ger äte besc hrei bu ng/A nsc hlüss e/L eist ungs ko ntakt e/F eldv ers orgung - Ü bers chri ft 3 @ 6\mod_1256294692864_21.docx @ 43664 @ 3 @ 1

3.2.2 Power Jumper Contacts/Field Supply

Pos: 18.1 2. 1 /S erie 750 ( W AGO -I/O-SY ST EM) /Wic htig e Er l äuter ung en /Sic her hei ts- un d s onsti ge H in wei se/V ors ich t/V orsic ht: Ver let zu ngsg efa hr d urc h sc har fka ntige Mes ser kon ta kte! @ 6\mod_1256193279401_21.docx @ 43414 @ @ 1

Risk of injury due to sharp-edged blade contacts!

The blade contacts are sharp-edged. Handle the I/O module carefully to prevent

injury.

Pos: 18.1 2. 2 /S erie 750 ( W AGO -I/O-SY ST EM) /Ger äte bes chr eib ung/ Ans chl üss e/L eist ungs kon tak te 2 LK ( M esser /Lei st ung sko nta kte 2 LK (Mes ser /F eder ) - E inl eitu ng @ 15\ mod_1371721641099_21.docx @ 123714 @ @ 1

The I/O module 750-516 has 2 self-cleaning power jumper contacts that supply

and transmit power for the field side. The contacts on the left side of the I/O

module are designed as blade contacts and those on the right side as spring

contacts.

Pos: 18.1 2. 3 /S erie 750 ( W AGO -I/O-SY ST EM) /Ger äte bes chr eib ung/ Ans chl üss e/L eist ungs kon tak te 2 LK ( M esser /Lei st ung sko nta kte 2 LK (Mes ser /F eder ) - A bbil dung , ei nf ache Br eite - St an dard @ 1 5\mod_1367500700037_21.docx @ 118 396 @ @ 1

Figure 3: Power Jumper Contacts

Pos: 18.1 2. 4 /S erie 750 ( W AGO -I/O-SY ST EM) /Ger äte bes chr eib ung/ Ans chl üss e/L eist ungs kon tak te 2 LK ( M esser /Lei st ung sko nta kte 2 LK (Mes ser /F eder ) - Leg en de @ 1 5\mod_1371721352500_21.docx @ 12 3710 @ @ 1

Table 4: Legend for Figure “Power Jumper Contacts”

Contact

Type

Function

Spring contact

Potential transmission (U

) for field supply

Spring contact

Potential transmission (0 V) for field supply

Blade contact

Potential feed-in (0 V) for field supply

Blade contact

Potential feed-in (U

) for field supply

Pos: 18.1 2. 5 /S erie 750 ( W AGO -I/O-SY ST EM) /Wic htig e Er l äuter ung en /Sic her hei ts- un d sonsti ge Hin weise /Acht ung/A chtung : Maxi maler Stro m Leistu ngsko ntakt e 10 A @ 3\mod_1226499143500_21.docx @ 25029 @ @ 1

Do not exceed maximum current via power jumper contacts!

The maximum current to flow through the power jumper contacts is 10 A.

Greater currents can damage the contacts.

When configuring your system, ensure that this current is not exceeded. If

exceeded, insert an additional supply module.

Pos: 18.1 2. 6 /S erie 750 ( W AGO -I/O-SY ST EM) /Wic htig e Er l äuter ung en /Sic her hei ts- un d s onsti ge H in wei se/H in weis /Hi nwei s: P ot ential ei nsp eis ekle mm e für Er de eins etz en! (kei ne LK f ür Er de) @ 3\mod_1226499037468_21.docx @ 25023 @ @ 1

18 Device Description WAGO-I/O-SYSTEM 750

750-516 4DO 24V DC 0.5A/ low-side switching

Manual

Version 1.1.0

Use supply modules for ground (earth)!

The I/O module has no power jumper contacts for receiving and transmitting the

earth potential. Use a supply module when an earth potential is needed for the

subsequent I/O modules.

Pos: 18.1 3 /D ok um entati o n allg em ein/ Gli eder ung sel eme nte/---S eit enw echs el--- @ 3\ mod_1221108045078_0.docx @ 21810 @ @ 1

WAGO-I/O-SYSTEM 750 Device Description 19

750-516 4DO 24V DC 0.5A/ low-side switching

Manual

Version 1.1.0

Pos: 18.1 4 / Ser ie 7 50 ( WAG O-I/ O-SYST EM )/G erät ebe schr eib ung /A nsc hlüss e/C AGE C L AMP-A nschlüsse - Ü bersc hrift 3 @ 6\mod_1256296337770_21.docx @ 43674 @ 3 @ 1

3.2.3 CAGE CLAMP

Connectors

Pos: 18 .15 /S erie 750 ( WAG O-I/O-SY ST EM) /Ger äte bes chr eib ung /Ansc hlüs se/ Dig it alaus ga ngs klem me n/Ans chl üss e 7 50-05xx 4 D O 3-Leit er ( DO, 24 V, 0 V) @ 1 8\mod_1390224596533_21.docx @ 142429 @ @ 1

Figure 4: CAGE CLAMP

Connectors

Table 5: Legend for Figure “CAGE CLAMP

Connectors”

Channel

Designation

Connector

Function

DO 1

Output DO 1: Signal voltage

DO 2

Output DO 2: Signal voltage

DO 3

Output DO 3: Signal voltage

DO 4

Output DO 4: Signal voltage

+24 V

Field supply +24 V

+24 V

Field supply +24 V

0 V

Field supply 0 V

0 V

Field supply 0 V

Pos: 18.1 6 /D ok um entati o n allg em ein/Gl i ederu ngsel e ment e/---Seit enw echs el--- @ 3 \mod_1221108045078_0.docx @ 21810 @ @ 1

20 Device Description WAGO-I/O-SYSTEM 750

750-516 4DO 24V DC 0.5A/ low-side switching

Manual

Version 1.1.0

Pos: 18.1 7 / Alle Ser ie n (All ge mein e M odul e) /Üb ersc hri ften für all e S eri en/G erät ebes chr ei bung /An zeig eel em ent e - Ü bersc hri ft 2 @ 4\mod_1240984390875_21.docx @ 31964 @ 2 @ 1

3.3 Display Elements

Pos: 18.1 8 / Ser ie 7 50 ( WAG O-I/ O-SYST EM)/ Gerät ebesc hreib ung/ Anzeig eele mente/ Digi tala usgang skle mmen/A nzei geele mente 7 50-05 xx 4DO @ 11 \mod_1322035869631_21.doc x @ 83554 @ @ 1

Figure 5: Display Elements

Table 6: Legend for Figure “Display Elements”

Channel

Designation

LED

State

Function

1 Status DO 1 A

Off

Output DO 1: Signal voltage “0”

Green

Output DO 1: Signal voltage “1”

2 Status DO 2 C

Off

Output DO 2: Signal voltage “0”

Green

Output DO 2: Signal voltage “1”

3 Status DO 3 B

Off

Output DO 3: Signal voltage “0”

Green

Output DO 3: Signal voltage “1”

4 Status DO 4 D

Off

Output DO 4: Signal voltage “0”

Green

Output DO 4: Signal voltage “1”

Pos: 18.1 9 / Alle Ser ie n (All ge mein e M odul e) /Üb ersc hri ften für all e S eri en/G erät ebes chr ei bung /Sc he matis ch es Schal tbi ld - Über schri ft 2 @ 4\mod_1240984441312_21.docx @ 31967 @ 2 @ 1

3.4 Schematic Diagram

Pos: 18.2 0 / Ser ie 7 50 ( WAG O-I/ O-SYST EM)/ Gerät ebesc hreib ung/ Schem atisc he Schal tbilder/Digital ausgangsklemmen/Sc hematisches Schaltbild 750- 0516 @ 20\mod_1411400972664_21.doc x @ 164108 @ @ 1

Figure 6: Schematic diagram

Pos: 18.2 1 /D ok um entati o n allg em ein/ Gli eder ung sel eme nte/---S eit enw echs el--- @ 3\ mod_1221108045078_0.docx @ 21810 @ @ 1

Page is loading ...