Comtrol RocketLinx ES8510-XTE User guide

Category
Networking
Type
User guide
Industrial Managed Switch
7 - 10/100BASE-TX Ethernet Ports
3 - 10/100BASE-TX RJ45/SFP Combo Ports
User Guide
Copyright Notice
Comtrol and RocketLinx are trademarks of Comtrol Corporation.
Microsoft and Windows are trademarks of Microsoft Corporation.
FireFox is a trademark of Mozilla Foundation.
PuTTY is a copyright of Simon Tatham.
Other product names mentioned herein may be trademarks and/or registered trademarks of their respective owners.
Fourth Edition, October 12, 2016
Copyright © 2010 - 2016. Comtrol Corporation.
All Rights Reserved.
Comtrol Corporation makes no representations or warranties with regard to the contents of this document or to the suitability of the
Comtrol product for any particular purpose. Specifications are subject to change without notice. Some software or features may not be
available at the time of publication. Contact your reseller for current product information.
Federal Communications Commission (FCC) Statement
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference in which case the user is required to correct the interference at his expense.
The user is cautioned that changes and modifications made to the equipment without approval of the manufacturer could void the user's
authority to operate this equipment.
Document Number: 2000574 Rev E
Table of Contents RocketLinx ES8510-XTE User Guide: 2000574 Rev. E - 3
Table of Contents
Introduction .......................................................................................................................................... 7
Hardware Installation ........................................................................................................................ 9
Connect the Power and Ground................................................................................................................. 9
Connect the Digital Input s and Relay Outputs ...................................................................................10
Mount the ES8510-XTE ............................................................................................................................... 11
Connect the Ethernet Ports ...................................................................................................................... 12
Connect SFP Transceivers (Combo Ports 8-10).................................................................................... 12
LED Descriptions......................................................................................................................................... 13
Panel Layout................................................................................................................................................. 14
Reset Button ................................................................................................................................................. 14
Using PortVision DX .........................................................................................................................15
PortVision DX Overview ............................................................................................................................ 15
PortVision DX Requirements.................................................................................................................... 16
Installing PortVision DX............................................................................................................................ 16
Configuring the Network Settings .......................................................................................................... 18
Checking the Firmware Version.............................................................................................................. 21
Uploading the Latest Firmware or Bootloader .................................................................................... 22
Uploading Firmware to Multiple ES8510-XTE Switches.................................................................... 23
Adding a New Device in PortVision DX ................................................................................................. 24
Using Configuration Files ......................................................................................................................... 25
Saving a Configuration File ..................................................................................................................... 25
Loading a Configuration File ................................................................................................................... 25
Using the LED Tracker............................................................................................................................... 26
Customizing PortVision DX ...................................................................................................................... 27
Accessing RocketLinx Documentation from PortVision DX............................................................. 28
How to Download Documentation ........................................................................................................... 28
How to Open Previously Downloaded Documents .................................................................................. 29
Configuration Using the Web User Interface..............................................................................31
Configuration Overview ............................................................................................................................ 31
Web User Interface ................................................................................................................................... 32
Secure Web User Interface....................................................................................................................... 33
Feature Overview ........................................................................................................................................ 35
Basic Settings ............................................................................................................................................... 44
Switch Setting........................................................................................................................................... 44
Admin Password ....................................................................................................................................... 46
IP Configuration ....................................................................................................................................... 47
Time Setting.............................................................................................................................................. 49
DHCP Server Configuration .................................................................................................................... 52
DHCP Leased Entries .............................................................................................................................. 54
DHCP Option82 Relay Information......................................................................................................... 55
Backup and Restore.................................................................................................................................. 57
Backup the Configuration - Local File Method ................................................................................ 58
Restore the Configuration - Local Method........................................................................................58
Backup the Configuration - TFTP Server Method ........................................................................... 59
Restore the Configuration - TFTP Server Method ........................................................................... 60
4 - RocketLinx ES8510-XTE User Guide: 2000574 Rev. E Table of Contents
Table of Contents
Firmware Upgrade .................................................................................................................................. 61
Upgrading Firmware (Local File)...................................................................................................... 61
Upgrading Firmware (TFTP Server)................................................................................................. 62
Load Default.............................................................................................................................................. 62
System Reboot........................................................................................................................................... 63
Port Configuration ...................................................................................................................................... 64
Port Control............................................................................................................................................... 64
Port Status ................................................................................................................................................ 66
Rate Control .............................................................................................................................................. 68
Port Trunking ........................................................................................................................................... 69
Aggregation Setting ........................................................................................................................... 69
Aggregation Information.................................................................................................................... 70
Network Redundancy................................................................................................................................. 71
STP Configuration .................................................................................................................................... 72
STP Port Configuration............................................................................................................................ 73
STP Information ....................................................................................................................................... 74
MSTP Configuration................................................................................................................................. 76
MSTP Port Configuration ........................................................................................................................ 78
MSTP Information.................................................................................................................................... 79
Redundant Ring ........................................................................................................................................ 81
Redundant Ring Information ................................................................................................................... 83
Loop Protection ......................................................................................................................................... 84
VLAN............................................................................................................................................................... 85
VLAN Configuration................................................................................................................................. 86
VLAN Port Configuration ........................................................................................................................ 88
VLAN Information.................................................................................................................................... 90
Private VLAN............................................................................................................................................ 91
PVLAN Configuration .............................................................................................................................. 91
PVLAN Port Configuration ...................................................................................................................... 92
PVLAN Information ................................................................................................................................. 93
GVRP Configuration................................................................................................................................. 94
Traffic Prioritization .................................................................................................................................. 95
QoS Setting ............................................................................................................................................... 95
CoS-Queue Mapping................................................................................................................................. 97
DSCP-Queue Mapping ............................................................................................................................. 98
Multicast Filtering ...................................................................................................................................... 99
IGMP Query ............................................................................................................................................ 100
IGMP Snooping....................................................................................................................................... 101
SNMP ............................................................................................................................................................ 102
SNMP Configuration .............................................................................................................................. 102
SNMP V3 Profile..................................................................................................................................... 103
SNMP Traps............................................................................................................................................ 104
Security ........................................................................................................................................................ 105
Port Security ..................................................................................................................
......................... 105
IP Security............................................................................................................................................... 106
802.1X Configuration.............................................................................................................................. 107
802.1X Port Configuration ..................................................................................................................... 109
802.1X Port Information......................................................................................................................... 111
Warning........................................................................................................................................................ 112
Fault Relay.............................................................................................................................................. 112
Event Selection ....................................................................................................................................... 113
SysLog Configuration ............................................................................................................................. 114
SMTP Configuration............................................................................................................................... 115
Table of Contents RocketLinx ES8510-XTE User Guide: 2000574 Rev. E - 5
Table of Contents
Monitor and Diag....................................................................................................................................... 116
LLDP Configuration ............................................................................................................................... 116
MAC Address Table ................................................................................................................................ 118
Port Statistics ......................................................................................................................................... 120
Port Mirroring......................................................................................................................................... 121
Event Logs............................................................................................................................................... 122
Ping Utility.............................................................................................................................................. 122
Device Front Panel.................................................................................................................................... 123
Save to Flash............................................................................................................................................... 124
Logout........................................................................................................................................................... 124
Configuration Using the Command Line Interface (CLI) ......................................................126
Overview...................................................................................................................................................... 126
Using the Serial Console ........................................................................................................................ 127
Using a Telnet/SSH Console .................................................................................................................. 130
Command Line Interface Introduction ................................................................................................ 131
User EXEC Mode.................................................................................................................................... 132
Accessing the Options for a Command................................................................................................. 132
Privileged EXEC Mode ........................................................................................................................... 134
Global Configuration Mode .................................................................................................................... 135
(Port) Interface Configuration ............................................................................................................... 136
(VLAN) Interface Configuration ............................................................................................................ 137
Command Mode Summary ...................................................................................................................... 137
Basic Settings (CLI) .................................................................................................................................. 140
Port Configuration (CLI) ......................................................................................................................... 146
Network Redundancy (CLI) .................................................................................................................... 151
VLAN (CLI) .................................................................................................................................................. 159
Private VLAN (CLI) ................................................................................................................................... 162
Traffic Prioritization (CLI) ..................................................................................................................... 166
Multicast Filtering (CLI).......................................................................................................................... 169
SNMP (CLI) ................................................................................................................................................. 172
Security (CLI) ............................................................................................................................................. 173
Warnings (CLI) ........................................................................................................................................... 175
Monitor and Diag (CLI) ............................................................................................................................ 179
Saving to Flash (CLI) ................................................................................................................................ 182
Logging Out (CLI)...................................................................................................................................... 182
Service (CLI) ............................................................................................................................................... 182
Complete CLI List............................................................................................................................183
User EXEC Mode ........................................................................................................................................ 183
Privileged EXEC Mode ............................................................................................................................. 184
Global Configuration Mode..................................................................................................................... 189
Port Interface Configuration Mode....................................................................................................... 194
VLAN Interface Configuration Mode.................................................................................................... 196
ModBus TCP /IP Support ...............................................................................................................197
Overview...................................................................................................................................................... 197
Modbus TCP/IP Function Codes ............................................................................................................ 198
Error Checking .......................................................................................................................................... 198
Exception Response .................................................................................................................................. 199
Modbus TCP Register Table.................................................................................................................... 199
CLI Commands for Modbus TCP/IP ...................................................................................................... 206
6 - RocketLinx ES8510-XTE User Guide: 2000574 Rev. E Table of Contents
Table of Contents
Technical Support ...........................................................................................................................207
Comtrol SFP Modules ............................................................................................................................... 207
Comtrol Private MIB................................................................................................................................. 207
Comtrol Support ........................................................................................................................................ 207
RocketLinx ES8510-XTE User Guide: 2000574 Rev. E Introduction - 7
Introduction
The ES8510-XTE is a managed industrial Ethernet switch that is equipped with ten 10/100BASE-TX ports,
which supplies three Combo ports that provide:
• Copper RJ45 Ethernet ports (10BASE-T and 100BASE-TX)
• SFP slots (100BASE-FX)
When the SFP port is active and installed on a Combo port, the corresponding Combo RJ45 port is
inactivated. For example, if an SFP transceiver is installed and active on the 8SFP port, the corresponding
RJ45 Port 8 becomes inactive.
The embedded software supports full Layer 2 networking features. In addition, the ES8510-XTE provides ring
redundancy, network control, security, and alert features. Security is enhanced with advanced features such
as IEEE 802.1Q VLAN and port/IP security. Performance is optimized by QoS and IGMP Snooping/Query.
Redundant Ring technology enables superb self-healing capability for network failure and it also provides an
advanced redundant network solution; Ring Coupling and Rapid Dual Homing technology. Ring Coupling and
Rapid Dual Homing technology means that an Ethernet Ring can be extended more easily whether with
Comtrol switches or other managed switches. Event warnings can be sent to the network administrator by
email or system log and to field engineers by relay output.
The ES8510-XTE has rugged aluminum housing and was designed for industrial environments. The
ES8510-XTE provides a wide operating temperature and is NEMA TS2 certified.
Detailed specifications for the ES8510-XTE are available on the Comtrol web site
.
You can refer to Feature Overview
on Page 35 for web user interface features.
8 - Introduction RocketLinx ES8510-XTE User Guide: 2000574 Rev. E
Introduction
RocketLinx ES8510-XTE User Guide: 2000574 Rev. E Hardware Installation - 9
Hardware Installation
You can use the following subsections to install the RocketLinx ES8510-XTE.
• Connect the Power and Ground
• Connect the Digital Input s and Relay Outputs on Page 10
• Mount the ES8510-XTE
on Page 11
• Connect the Ethernet Ports
on Page 12
• Connect SFP Transceivers
(Combo Ports 8-10) on Page 12
• LED Descriptions
on Page 13
• Panel Layout
on Page 14
• Reset Button
on Page 14
Connect the Power and Ground
Use the following procedure to connect the power and ground.
You can use the following procedure to connect power and the ground to the ES8510-XTE.
1. Connect the DC power inputs by inserting the positive and negative wires (12-24AWG) into the PW+ and
PW- contacts.
Note: Power should be disconnected from the power supply before connecting it to the switch.
Otherwise, your screw driver blade can inadvertently short your terminal connections to the
grounded enclosure.Tighten the wire-clamp screws to prevent the wires from coming loose.

This switch is intended to be installed in a
RESTRICTED ACCESS LOCATION ONLY.
AC Power Input
AC Power Input
Power Supply
10 - 60VDC
(UL Listed)
Power Supply
10 - 60VDC
(UL Listed)
V-
V+
V-
V+
12 - 24AWG Wire
12 - 24AWG Wire
Wiring Power Supplies
10 - Connect the Digital Input s and Relay Outputs RocketLinx ES8510-XTE User Guide: 2000574 Rev. E
Hardware Installation
• PWR1 and PWR2 support power redundancy and reverse polarity protection.
• Accepts a positive or negative power source but PW1 and PW2 must apply to the same mode.
• If both power inputs are connected, the ES8510-XTE is powered from the highest connected
voltage.
• The ES8510-XTE can emit an alarm if PW1 or PW2 are no longer receiving power. See the Warning
discussion on Page 112
to configure an alarm.
2. Connect a ground wire between the chassis and earth ground using
12-24AWG wire to ensure that the ES8510-XTE is not damaged by
noise or electrical shock.
a. Loosen the ground screw on the bottom of the ES8510-XTE.
b. Insert the ground wire.
c. Tighten the ground screw after the ground wire is connected.
Connect the Digital Input s and Relay Outputs
The ES8510-XTE provides two digital inputs and two digital outputs (dry relay output) on terminal block
connectors on the bottom of the unit. The fault conditions can be configured in the web user interface or
Command Line Interface (CLI) and include:
•DI State
• Power failure
• Ethernet port link break
•Dry output
• Ping failure
• Super Ring failure
You can configure events using one of the ES8510-XTE user interfaces (Fault Relay
on Page 112) or the
Command Line Interface (Global Configuration Mode
on Page 135).
The Digital Input pin can be pulled
high or low so that the connected
equipment can actively drive these
pins. The web user interface allows
you to read and set the value to the
connected device. The power input
voltage of logic low is 0 to 10VDC and
logic high is 11 to 30VDC. Do not apply
a higher voltage than the specification;
it may cause internal circuit damage
or a cause an incorrect DI action.
Digital Input
RocketLinx ES8510-XTE User Guide: 2000574 Rev. E Mount the ES8510-XTE - 11
Hardware Installation
Digital output relay contacts are
energized (open) for normal operation
and close for fault conditions. The
digital output relay contacts support up
to 1A at 24VDC. Do not apply voltage
and current higher than the
specifications.
1. Insert the positive and negative
wires (12-24 AWG) into V+ and V-.
2. Tighten the wire-clamp screws to
prevent the wires from coming
loose.
Mount the ES8510-XTE
You can use the following procedure to mount the ES8510-XTE on a DIN rail or on the wall.
The DIN rail clip is already attached to the ES8510-XTE. If the DIN rail clip is not screwed onto the
ES8510-XTE, follow the instructions and the figure below to attach DIN rail clip to the ES8510-XTE.
Digital Output
1. If necessary, use the screws to attach DIN rail clip to the rear
panel of the ES8510-XTE. (To remove DIN rail clip, reverse Step
1.)
2. Insert the upper end of DIN rail clip into the back of DIN rail
track from its upper side.
3. Lightly push the bottom of DIN rail clip into the track.
4. Verify that the DIN rail clip is tightly attached on the track.
5. To remove the ES8510-XTE from the track, reverse the steps
above.
DIN Rail Mounting
Follow the steps below to install the ES8510-XTE with the wall mounting plate:
1. To remove the DIN rail clip from the ES8510-XTE, loosen the screws from the DIN rail
clip.
2. Place the wall mounting plate on the rear panel of the ES8510-XTE.
3. Use the screws to attach the wall mounting plate to the ES8510-XTE.
4. Use the hook holes at the corners of the wall mounting plate to hang the ES8510-XTE
onto the wall.
5. To remove the wall mounting plate, reverse the steps above.
Wall Mount Installation
12 - Connect the Ethernet Ports RocketLinx ES8510-XTE User Guide: 2000574 Rev. E
Hardware Installation
Connect the Ethernet Ports
You can use the following information to connect standard Ethernet cables between the ES8510-XTE
Ethernet ports and the network nodes.
• Ports 8-10 are RJ45/SFP Combo ports that support (10/100BASE-TX / 100BASE-FX)
.
See Connect SFP Transceivers (Combo Ports 8-10) on Page 12 for information about SFP installation.
All of the Ethernet ports automatically detect the signal from the connected devices to negotiate the link
speed and duplex mode (half- or full-duplex). Auto MDI/MDIX allows you to connect another switch, hub, or
workstation without changing straight-through or crossover cables. Crossover cables cross-connect the
transmit lines at each end to the received lines at the opposite end.
Connect one side of an Ethernet cable into any switch port and connect the other side to
your attached device. The LNK/ACT LED is lit when the cable is correctly connected.
Always make sure that the cables between the switches and attached devices (for example,
switch, hub, or workstation) are less than 100 meters (328 feet) and meet these
requirements.
• 10BASE-T: Category 3 or higher cable
• 100BASE-TX: Category 5 or higher cable
Connect SFP Transceivers (Combo Ports 8-10)
The ES8510-XTE equips three SFP ports
combined with RJ45 Fast Ethernet ports (Ports
8-10), The SFP ports accept standard mini GBIC
SFP transceivers. that support 100BASE-FX.
To ensure system reliability, Comtrol
recommends using Comtrol certified SFP
Transceivers.
1. Plug the SFP transceiver into the SFP fiber
transceiver.
2. Connect the transmit channel to the receive
channel at each end.
3. Check the direction/angle of the fiber transceiver and the fiber cable.
Note: This is a Class 1 Laser/LED product. Do not stare at the Laser/LED Beam.
The SFP port does not function until the fiber cable is linked to another active device. The SFP and
corresponding RJ45 ports work in an exclusive mode. Traffic sent or received through the SFP module has
priority thus no traffic is sent or received over the corresponding RJ45 connection. To use the RJ45
connection, remove the corresponding SFP.
Multi-Mode cables should not exceed 2KM and Single-Mode cables should not exceed 30km.
Switch
3 TD+
6 TD-
1 RD+
2 RD-
3 RD+
6 RD-
1 TD+
2 TD-
Router or PC
Switch
3 TD+
6 TD-
1 RD+
2 RD-
3 TD+
6 TD-
1 RD+
2 RD-
Switch
Straight-Through Cabling Crossover Cabling
100BASE-TX
10BASE-TX
RocketLinx ES8510-XTE User Guide: 2000574 Rev. E LED Descriptions - 13
Hardware Installation
LED Descriptions
This subsection provides information about the ES8510-XTE LEDs. You can also refer to Device Front Panel
on Page 123 for information about using the web user interface to remotely view LED information.
LED Name LED On LED Blinking LED Off
Power 1
Power 2
Green: Power available No power
DO1 (Digital Output)
DO2 (Digital Output)
Red: DO activated DO not activated
DI1 (Digital Input)
DI2 (Digital Input)
Green: DI activated DI not activated
R.M. (ring master) Green: Working as a Ring
Master
Green: Ring failed Ring function disabled or
the ES8510-XTE is on a
ring but not the ring
master
1 - 7 
Green: Linked to another
device



Amber: Full-Duplex

Green: Active traffic




Not connected



Collision
8 - 10
SFP
RJ45

Green: Connected
Green: Active connection

Green: Active
connection
Green: Active
connection

Plugged in but not linked
up
Not connected
Link/
Speed
14 - Panel Layout RocketLinx ES8510-XTE User Guide: 2000574 Rev. E
Hardware Installation
Panel Layout
Reset Button
The ES8510-XTEhas a reset button that you can use to reboot the ES8510-XTE or reset the configuration to
the factory default.
The Reset button is located on the front panel of the ES8510-XTE to the right of the RS LED.
Reset Button Description
Depress 5 Seconds
This reboots the ES8510-XTE without changing the
configuration.
Depress > 10
Seconds
This loads the factory default configuration values into the
ES8510-XTE including the IP address.
Combo Port
LEDs
SFP Ports
Combo Ports
10/100BASE-TX
RS-232 Console
Port
100BASE-FX
Reset
Button
Fast Ethernet Ports
10/100BASE-TX
Fast Ethernet Ports
RocketLinx ES8510-XTE User Guide: 2000574 Rev. E Using PortVision DX - 15
Using PortVision DX
There are several ways to configure network information. Comtrol Technical Support recommends connecting
the ES8510-XTE to a PC or laptop running Windows
and installing PortVision DX for initial configuration.
This section shows how to use PortVision DX for initial network configuration and discusses how to:
• Install PortVision DX (Page 16
)
• Configure the network address (Page 18
)
• Check the firmware and bootloader version on the ES8510-XTE to verify that the latest versions are
loaded (Page 21
) before configuration
• Download the latest version firmware and bootloader and upload it to the ES8510-XTE (Page 22
)
• Perform other PortVision DX tasks, such as:
- Uploading firmware to multiple ES8510-XTE switches (Page 23)
- Adding a new RocketLinx (managed or unmanaged) or a third party device to PortVision DX to
maintain device information on your network (
Page 24)
- Using configuration files for use in configuring multiple installations with the same features (Page 25)
- Using the LED Tracker (Page 26)
• Organize how PortVision DX displays your Comtrol Ethernet attached products (Page 25)
• Access the latest documentation for your Comtrol Ethernet attached product
Optionally, you can use the web user interface or the CLI to perform these tasks on the ES8510-XTE using
these subsections:
• IP Configuration
on Page 47
• Firmware Upgrade
on Page 61
• Basic Settings (CLI)
on Page 140
PortVision DX Overview
PortVision DX automatically detects Comtrol Ethernet attached products physically attached to the local
network segment so that you can configure the network address, upload firmware, and manage the following
products:
• RocketLinx (managed) switches
• DeviceMaster family
- DeviceMaster PRO/DeviceMaster RTS/DeviceMaster Serial Hub
- DeviceMaster 500
•DeviceMaster UP
•DeviceMaster LT
•IO-Link Master family
In addition to identifying Comtrol Ethernet attached products, you can use PortVision DX to display any
third-party switch and hardware that may be connected directly to those devices. All non-Comtrol products
and unmanaged RocketLinx switches are treated as non-intelligent devices and have limited feature support.
For example, you cannot configure or update firmware on a third-party switch.
Note: After initial IP configuration, you may want to disable PortVision DX using the service netvision
command to secure your switch. See Securing Interfaces
on Page 176 for information about disabling
PortVision DX.
16 - PortVision DX Requirements RocketLinx ES8510-XTE User Guide: 2000574 Rev. E
Using PortVision DX
PortVision DX Requirements
Use PortVision DX to identify, configure, update, and manage the ES8510-XTE on Windows XP SP3 through
Windows 10 operating systems (at the time of publication).
PortVision DX requires that you connect the Comtrol Ethernet attached product to the same network segment
as the Windows host system if you want to be able to scan and locate it automatically during the configuration
process.
Installing PortVision DX
During initial configuration, PortVision DX automatically detects and identifies ES8510-XTE switches, if they
are in the same network segment.
You can download the latest version of PortVision DX from: http://downloads.comtrol.com/rocketlinx/
portvision_dx.
1. Execute the PortVision_DX[version].msi file.
Note: Depending on your operating system, you may need to respond to a Security Warning to permit
access.
2. Click Next on the Welcome screen.
3. Click I accept the terms in the License Agreement and Next.
4. Click Next or optionally, browse to a different location and
then click Next.
RocketLinx ES8510-XTE User Guide: 2000574 Rev. E Installing PortVision DX - 17
Using PortVision DX
5. Click Next to configure the shortcuts.
6. Click Install.
7. Depending on the operating system, you may need to click Yes to
the Do you want to allow the following program to install software
on this computer? query.
8. Click Launch PortVision DX and Finish in the last installation
screen.
9. Depending on the operating system, you may need to click Yes to
the Do you want to allow the following program to make changes
to this computer? query.
10. Go the next subsection to use PortVision DX to program the
network information.
18 - Configuring the Network Settings RocketLinx ES8510-XTE User Guide: 2000574 Rev. E
Using PortVision DX
Configuring the Network Settings
The ES8510-XTE has the following default values when shipped from the factory:
• IP address: 192.168.250.250
• Subnet mask: 255.255.255.0
• Gateway address: 192.168.250.1
Use the following procedure to change the default network settings on the ES8510-XTE for your network.
1. If necessary, start PortVision DX using the PortVision DX desktop shortcut or from the Start button, click
All Programs > Comtrol > PortVision DX > PortVision DX.
Note: Depending on your operating system, you may need to click Ye s to the Do you want to allow the
following program to make changes to this computer? query.
2. Click the Scan button in the Toolbar.
3. Select the Comtrol Ethernet attached products that you
want to locate and then click Scan.
Note: If the Comtrol Ethernet attached product is not on
the local segment and it has been programmed
with an IP address, it will be necessary to
manually add the Comtrol Ethernet attached
product to PortVision DX.
4. Highlight the ES8510-XTE for which you want to
program network information and open the Properties
screen using one of these methods.
• Double-click the ES8510-XTE in the Device Tree or
Device List pane.
• Highlight the ES8510-XTE in the Device Tree or
Device List pane and click the Properties button.
• Right-click the ES8510-XTE in the Device Tree or Device List pane and click Properties in the popup
menu
RocketLinx ES8510-XTE User Guide: 2000574 Rev. E Configuring the Network Settings - 19
Using PortVision DX
• Highlight the ES8510-XTE, click the Manage menu and then Properties.
20 - Configuring the Network Settings RocketLinx ES8510-XTE User Guide: 2000574 Rev. E
Using PortVision DX
5. Optionally, rename the ES8510-XTE in the Device Name field for a PortVision DX friendly name. The
default name displays as Device and the last three sets of hex numbers from the MAC address.
Note: The MAC address and Device Status fields are automatically populated and you cannot change
these values.
6. Optionally, enter the serial number, which is on a label on the ES8510-XTE.
7. Select DHCP IP or Static IP for the IP Mode.
• If you select DHCP IP, go to Step 8
.
• If you select Static IP:
- Enter a unique IP address as required for your site.
- Enter a valid Subnet Mask value for your network.
- Enter a valid Default Gateway value for your network.
8. Optionally, select the Network Topology type, which is an informational field.
9. Click Apply Changes to update the network information on the ES8510-XTE.
Note: If you are deploying multiple ES8510-XTE switches that share common values, you can save the
configuration file and load that configuration onto other ES8510-XTE switches. See Using
Configuration Files on Page 25 for more information.
10. Click Close to exit the Properties window.
11. You should verify that you have the latest firmware loaded on the ES8510-XTE because a newer version
typically includes feature enhancements and bug fixes. Refer to Checking the Firmware Version
on Page
21 and if necessary, Uploading the Latest Firmware or Bootloader
on Page 22.
12. If you have the latest firmware, you can begin feature configuration, see one of these sections:
• Configuration Using the Web User Interface
on Page 31
• Configuration Using the Command Line Interface (CLI)
on Page 126
• Right-click the ES8510-XTE in the Device List pane and click Webpage in the popup menu.
Note: The default User Name and Password are both admin.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120
  • Page 121 121
  • Page 122 122
  • Page 123 123
  • Page 124 124
  • Page 125 125
  • Page 126 126
  • Page 127 127
  • Page 128 128
  • Page 129 129
  • Page 130 130
  • Page 131 131
  • Page 132 132
  • Page 133 133
  • Page 134 134
  • Page 135 135
  • Page 136 136
  • Page 137 137
  • Page 138 138
  • Page 139 139
  • Page 140 140
  • Page 141 141
  • Page 142 142
  • Page 143 143
  • Page 144 144
  • Page 145 145
  • Page 146 146
  • Page 147 147
  • Page 148 148
  • Page 149 149
  • Page 150 150
  • Page 151 151
  • Page 152 152
  • Page 153 153
  • Page 154 154
  • Page 155 155
  • Page 156 156
  • Page 157 157
  • Page 158 158
  • Page 159 159
  • Page 160 160
  • Page 161 161
  • Page 162 162
  • Page 163 163
  • Page 164 164
  • Page 165 165
  • Page 166 166
  • Page 167 167
  • Page 168 168
  • Page 169 169
  • Page 170 170
  • Page 171 171
  • Page 172 172
  • Page 173 173
  • Page 174 174
  • Page 175 175
  • Page 176 176
  • Page 177 177
  • Page 178 178
  • Page 179 179
  • Page 180 180
  • Page 181 181
  • Page 182 182
  • Page 183 183
  • Page 184 184
  • Page 185 185
  • Page 186 186
  • Page 187 187
  • Page 188 188
  • Page 189 189
  • Page 190 190
  • Page 191 191
  • Page 192 192
  • Page 193 193
  • Page 194 194
  • Page 195 195
  • Page 196 196
  • Page 197 197
  • Page 198 198
  • Page 199 199
  • Page 200 200
  • Page 201 201
  • Page 202 202
  • Page 203 203
  • Page 204 204
  • Page 205 205
  • Page 206 206

Comtrol RocketLinx ES8510-XTE User guide

Category
Networking
Type
User guide

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI