2. Computers & electronics
  3. TVs & monitors
  4. Flat panel desk mounts
  5. Peerless
  6. HL4UN-002-Q10

Peerless HL4UN-002-Q10, HL4UN-002 User manual

  • Hello! I am an AI chatbot trained to assist you with the Peerless HL4UN-002-Q10 User manual. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
1 of 2
ISSUED: 06-03-11 SHEET #:120-9110-1
Insert two 1/4-20 x 1-3/4" carriage bolts (A)
into bottom of display base as shown in detail 1.
Model: HL4UN-002, HL4UN-002-Q10
Installation and Assembly:
Lock Down Hardware for Display Base Stands
1
BOTTOM OF BASE
FRONT
2
FRONT
A B
C
D
A
DETAIL 1
MEASURE
DISTANCE
Measure distance between center lines of cut outs in
bottom of display base. Use measurement to mark
location of holes at point 1 and point 2, on table.
Drill two holes using a 9/32'' drill bit.
POINT 1
POINT 2
• drill
• 9/32" drill bit
• 5/8" open box wrench
E F
G
H
TOOLS NEEDED
HL4UN-002 HL4UN-002-Q10
Description Qty. Part # Qty. Part #
A
1/4-20 x 1 3/4" carriage bolt 2 520-1017 20 520-1017
B
M4 x 16 mm phillips trilobe screw 2 520-2621 20 520-2621
C
M4 x 16 mm socket pin screw 2 520-1087 20 520-1087
D
1/4-20 sloped nut 3 530-0035 23 530-0035
E
M4 x 12 mm socket pin screw
2
520-1079
20
520-1079
F
#8 flat washer
2
540-1001
20
540-1001
G
plastic cap
2
590-1294
20
590-1294
H
4 mm allen wrench 1 560-9646 3 560-9646
Parts List
NOTE: Display and base may appear
different than illustrated
2 of 2
ISSUED: 06-03-11 SHEET #:120-9110-1
Hand tighten slope nut (D) through 1/4-20 x 1-3/4" carriage bolt (A) until snug against bottom of desktop surface.
Thread another slope nut (D) upside-down, about two turns from rst slope nut (D). Insert an open box wrench
between both slope nuts (D) and tighten. NOTE: Avoid jamming both slope nuts (D) together, doing so may make
it difcult to remove slope nut used for tightening rst slope nut (D) as shown in gure 3.1. After slope nut is secure
remove bottom slope nut as shown in gure 3.2. Repeat with remaining 1/4-20 x 1 3/4" carriage bolt (A).
Fasten two plastic caps (G).
TIGHTENING
SLOPE NUT
BOTTOM OF DESKTOP
FIGURE 3.1 FIGURE 3.2
A
3
NOTE: Do not overtighten slope nut (D)
plate may distort
FRONT
D
A
D
Thread two M4 x 16 phillips pan trilobe screws (B) to bottom display attachment holes as shown in g. 4.1.
Remove the two M4 x 16 phillips pan trilobe screws (B) and attach display screen to display base using two M4 x
16 mm socket pin screws (I) or M4 x 12 mm socket pin screws (E) with #8 at washers (F), as shown in gure 4.2.
Tighten with 4 mm security allen wrench (H). Use TV supplied screws for remaining holes.
4
g 4.1 g 4.2
B
DISPLAY SCREEN
DISPLAY SCREEN
DISPLAY BASE
NOTE: Display and base may appear
different than illustrated
NOTE: Screws are installed using bottom
two display mounting locations.
Installation of Security Screws for Base/Screen Assembly
G
C or E
F
• If screws don’t get three complete turns in the screen inserts or if screws bottom out and bracket is still not tightly
secured, damage may occur to screen or product may fail.
WARNING
© 2011, Peerless Industries, Inc. All rights reserved.
All other brand and product names are trademarks or registered trademarks of their respective owners.
/