2. Computers & electronics
  3. Projectors
  4. Projector mounts
  5. Optoma
  6. BM-3001N

Optoma BM-3001N Specification

  • Hello! I am an AI chatbot trained to assist you with the Optoma BM-3001N Specification. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
Visit the Peerless Web Site at www.peerlessmounts.com
ISSUED: 11-18-10 SHEET #: 125-9159-1
This product is intended for use with UL
Listed products and must be installed by a
qualied professional installer.
Maximum UL Load Capacity:
35 lb (15.8 kg)
Model: BM-3001N
Installation and Assembly:
Dual Stud Short Throw Projector Wall Mount
Visit the Peerless Web Site at www.peerlessmounts.com
Note: Read entire instruction sheet before you start installation and assembly.
Table of Contents
Parts List.................................................................................................................................................................................3
Installation to Wood ...............................................................................................................................................................4
Installation to Concrete/Cinder Block ....................................................................................................................................5
Assembly of Adjustment Tube ...............................................................................................................................................8
Installing Projector Mount ......................................................................................................................................................8
Routing Cables .......................................................................................................................................................................9
2 of 13
ISSUED: 11-18-10 SHEET #: 125-9159-1
• DonotbegintoinstallyourPeerlessproductuntilyouhavereadandunderstoodtheinstructionsandwarnings
containedinthisInstallationSheet.Ifyouhaveanyquestionsregardinganyoftheinstructionsorwarnings,please
call Peerless customer care at 1-800-865-2112.
• Thisproductshouldonlybeinstalledbysomeoneofgoodmechanicalaptitude,hasexperiencewithbasicbuilding
construction,andfullyunderstandstheseinstructions.
• Makesurethatthesupportingsurfacewillsafelysupportthecombinedloadoftheequipmentandallattachedhard-
ware and components.
• NeverexceedtheMaximumULLoadCapacity.Seepage1.
• Ifmountingtowoodstuds,makesurethatmountingscrewsareanchoredintothecenterofthestuds.Useofan
“edgetoedge”studnderishighlyrecommended.
• Alwaysuseanassistantormechanicalliftingequipmenttosafelyliftandpositionequipment.
• Tightenscrewsrmly,butdonotovertighten.Overtighteningcandamagetheitems,greatlyreducingtheirholding
power.
• Thisproductisintendedforindooruseonly.Useofthisproductoutdoorscouldleadtoproductfailureandpersonal
injury.
• Thisproductwasdesignedandintendedtobemountedtothefollowingsupportingsurfacescheckedbelowwith
thehardwareincludedinthisproductasspeciedintheinstallationsheet.Tomountthisproducttoanalternative
supportingsurface,contactPeerlesscustomercareat1800865-2112.
• Thisproductwasdesignedtobeinstalledonthefollowingwallconstructiononly;
WALL CONSTRUCTION ADDITIONAL HARDWARE REQUIRED
x WoodStud None
x SolidConcrete None
x CinderBlock None
MetalStud ContactCustomerService(NotEvaluatedByUL)
Brick ContactCustomerService(NotEvaluatedByUL)
Otherorunsure? ContactCustomerService
WARNING
Tools Needed for Assembly
• studnder(“edgetoedge”studnderrecommended)
• level
• drill
• 5/32” bit (wood installation)
• 1/4” bit (concrete/cinder block installation)
• phillipsscrewdriver
Accessories
• WSP320
(requiredforinstallationtometalstuds)(NotEvaluatedbyUL)
• ACC-MIS550
 (requiredforinstallationtometalstuds)(NotEvaluatedbyUL)
• ACC020ProjectorSecurityCable(NotEvaluatedbyUL)
• WBK100
 (wallplateaccessorykit)(NotEvaluatedbyUL)
A
B
C
D
E
F
G
H
I
J
K
L
M
3 of 13
ISSUED: 11-18-10 SHEET #: 125-9159-1
Before you start check the parts list to insure all of the parts shown are included.
N
O P
Q
R
S
T U
V
W
X
Y Z
Compatible Projector Models: EX525ST,TX610ST,TW610ST
AA
Description Qty. Part #
A
wall arm 1
055-1912
B
adjustment tube 1
055-1911
C 4 mm allen wrench 1 560-9646
D
M5x10mmserratedsocketpinscrew 2
510-1126
E
#14-x2.5phillipsheadwoodscrew 4
5S1-015-C03
F tube cap 1 590-1263
G concrete anchor 4 590-0320
H 1/4"-20 socket pin screw 2 520-1054
I 1/4"-20 flat washer 2 540-1078
J
precision gear projector mount 1 055-KPRGU-B-3
K wall plate 1 055-1923
L 5/16-18x1/2carriagebolt 4 520-9207
M 5/16 - 18 serrated flanged lock nut 4 530-1016
N
adapter plate 1 XXX-XXXX
O
10-32x3/8"socketpinserratedwasherheadscrew
2
520-1151
P
.219IDx.5ODx.125spacer
6
540-1032
Q
10-32x1/4"socketpinwithlockpatch 1 520-1196
R
#8 flat washer 8 540-1001
S
connection block
1
580-1065
T
extensionbracket 4 055-1940
U
M3x12mmsocketpinserratedwasherheadscrew 4 510-1003
V
M4x8mmsocketpinserratedwasherheadscrew
4
510-1005
W M4x12mmknob 2 560-1154
X .198x.313x.375spacers 1 590-2020
Y M4x16mmscrew 4 510-1087
Z M3x20mmknob 1 560-1149
AA 2 mm allen wrench 1 560-1097
Parts List
NOTE: Some parts may appear slightly different than illustrated.
Visit the Peerless Web Site at www.peerlessmounts.com
4 of 13
Installation to Wood Stud Walls
Useastudndertolocatetheedgesofthestud.Useofanedge-to-edgestudnderishighlyrecommended.
Basedonitsedges,drawaverticallinedownthestud’scenter.Placewallarm(A) on wall as a template. Mark the
center of the four mounting holes. Drill four 5/32” (4 mm) dia. holes 2-1/2” (65 mm) deep. Secure wall arm (A) to
woodstudusingfour#14x2-1/2”woodscrews(E) as shown.
Optional: Rotate wall arm 180
°
to position the arm closer to the ceiling.
Skip to Step 2.
• Installermustverifythatthesupportingsurfacewillsafelysupportthecombinedloadoftheequipmentandall
attached hardware and components.
• Tightenwoodscrewssothatwallplateisrmlyattached,butdonotovertighten.Overtighteningcandamagethe
screws,greatlyreducingtheirholdingpower.
• Nevertighteninexcessof80in.•lb(9N.M.).
• Makesurethatmountingscrewsareanchoredintothecenterofthestud.Theuseofan“edgetoedge”studnder
is highly recommended.
• Hardwareprovidedisforattachmentofmountthroughstandardthicknessdrywallorplasterintowoodstuds.
Installersareresponsibletoprovidehardwareforothertypesofmountingsituations(NotEvaluatedByUL).
WARNING
1
ISSUED: 11-18-10 SHEET #: 125-9159-1
A
E
Note: For mounting using wall plate (K),refertopage6.
Visit the Peerless Web Site at www.peerlessmounts.com
5 of 13
Installation to a concrete or cinder block wall
Drill four 5/16” (8 mm) dia. holes to a minimum depth of 2.5” (64 mm). Insert anchors (G)inholesushwith
wall as shown. Attach wall arm (A)usingfour#14x2-1/2”woodscrews(E) as shown in Illustration A and 1,
2,and3. Tighten all fasteners. Optional: Rotate wall arm 180
°
to position the arm closer to the ceiling.
1
• Tightenwoodscrewsrmly,butdonotovertighten.
Overtighteningcandamagethescrews,greatlyre-
ducing their holding power.
• Nevertighteninexcessof80in•lb(9N.M.).
WARNING
WARNING
• WheninstallingPeerlesswallmountsoncinderblock,verifythatyouhaveaminimumof1-3/8”ofactualcon-
crete surface in the hole to be used for the concrete anchors. Do not drill into mortar joints! Be sure to mount in
asolidpartoftheblock,generally1”minimumfromthesideoftheblock.CinderblockmustmeetASTMC-90
specications.Itissuggestedthatastandardelectricdrillonslowsettingisusedtodrilltheholeinsteadofa
hammerdrilltoavoidbreakingoutthebackoftheholewhenenteringavoidorcavity.
• Concretemustbe2000psidensityminimum.Lighterdensityconcretemaynotholdconcreteanchor.
• Makesurethatthewallwillsafelysupportfourtimesthecombinedloadoftheequipmentandallattachedhard-
ware and components.
E
G
Illustration A
A
ISSUED: 11-18-10 SHEET #: 125-9159-1
1
3
2
Tighten all fasteners.
concrete
surface
C
UTAWAY VIEW
INCORRECT CORRECT
wall
plate
wall
plate
plaster/
dry wall
plaster/
dry wall
concrete
concrete
Drill holes and insert anchors (G).
Place wall arm (A)overanchors(G) and secure with
screws (E).
Tighten all fasteners.
E
E
A
G
G
G
• Concreteanchorsarenot intended for attachment to
concretewallcoveredwithalayerofplaster,drywall,
orothernishingmaterial.Ifmountingtoconcrete
wallcoveredwithplaster/drywallisunavoidable(Not
EvaluatedByUL),plaster/drywall(upto5/8”thick)
must be counterbored as shown right. If plaster/dry-
wallisthickerthan5/8”,customfastenersmustbe
suppliedbyinstaller(NotEvaluatedByUL).
WARNING
CUTAWAY VIEW
INCORRECT CORRECT
wall
plate
wall
plate
plaster/
dry wall
plaster/
dry wall
concrete
concrete
Note: For mounting using wall plate (K),refertopage6.
Visit the Peerless Web Site at www.peerlessmounts.com
Secure wall arm (A) to wall plate (K) using four carriage bolts (L) and lock nuts (M).
K
L
M
K
E
1
Installation to Wall Plate
Useastudndertolocatetheedgesofthestud.Useofanedge-to-edgestudnderishighlyrecommended.
Basedonitsedges,drawaverticallinedownthestud’scenter.Placewallplate(K) on wall as a template. Mark
the center of the four mounting holes. Drill four 5/32” (4 mm) dia. holes 2-1/2” (65 mm) deep. Secure wall plate (K)
towoodstudusingfour#14x2-1/2”woodscrews(E) as shown. Skip to Step 2.
Optional: Rotate wall arm 180
°
to position the arm closer to the ceiling.
• Installermustverifythatthesupportingsurfacewillsafelysupportthecombinedloadoftheequipmentandall
attached hardware and components.
• Tightenwoodscrewssothatwallplateisrmlyattached,butdonotovertighten.Overtighteningcandamagethe
screws,greatlyreducingtheirholdingpower.
• Nevertighteninexcessof80in.•lb(9N.M.).
• Makesurethatmountingscrewsareanchoredintothecenterofthestud.Theuseofan“edgetoedge”studnder
is highly recommended.
• Hardwareprovidedisforattachmentofmountthroughstandardthicknessdrywallorplasterintowoodstuds.
Installersareresponsibletoprovidehardwareforothertypesofmountingsituations.(NotEvaluatedByUL)
WARNING
6 of 13
ISSUED: 11-18-10 SHEET #: 125-9159-1
Installation to Wood Stud Walls
A
1-1
Visit the Peerless Web Site at www.peerlessmounts.com
Installation to a concrete or cinder block wall
Drill four 5/16” (8 mm) dia. holes to a minimum
depth of 2.5” (64 mm). Insert anchors (G) in holes
ushwithwallasshown.Attachwallplate(K) using
four#14x2-1/2”woodscrews(E) as shown in
Illustration A and 1,2,and3. Tighten all fasteners.
Optional: Rotate wall arm 180
°
to position the arm
closer to the ceiling.
• Tightenwoodscrewsrmly,butdonotovertighten.
Overtighteningcandamagethescrews,greatlyre-
ducing their holding power.
• Nevertighteninexcessof80in•lb(9N.M.).
WARNING
WARNING
• WheninstallingPeerlesswallmountsoncinderblock,verifythatyouhaveaminimumof1-3/8”ofactualcon-
crete surface in the hole to be used for the concrete anchors. Do not drill into mortar joints! Be sure to mount in
asolidpartoftheblock,generally1”minimumfromthesideoftheblock.CinderblockmustmeetASTMC-90
specications.Itissuggestedthatastandardelectricdrillonslowsettingisusedtodrilltheholeinsteadofa
hammerdrilltoavoidbreakingoutthebackoftheholewhenenteringavoidorcavity.
• Concretemustbe2000psidensityminimum.Lighterdensityconcretemaynotholdconcreteanchor.
• Makesurethatthewallwillsafelysupportfourtimesthecombinedloadoftheequipmentandallattachedhard-
ware and components.
E
G
Illustration A
K
7 of 13
ISSUED: 11-18-10 SHEET #: 125-9159-1
1
3
2
Tighten all fasteners.
concrete
surface
C
UTAWAY VIEW
INCORRECT CORRECT
wall
plate
wall
plate
plaster/
dry wall
plaster/
dry wall
concrete
concrete
Drill holes and insert anchors (G).
Place wall plate (K)overanchors(G) and secure with
screws (E).
Tighten all fasteners.
E
E
K
G
G
G
• Concreteanchorsarenot intended for attachment to
concretewallcoveredwithalayerofplaster,drywall,
orothernishingmaterial.Ifmountingtoconcrete
wallcoveredwithplaster/drywallisunavoidable(Not
EvaluatedByUL),plaster/drywall(upto5/8”thick)
must be counter bored as shown right. If plaster/
drywallisthickerthan5/8”,customfastenersmustbe
suppliedbyinstaller(NotEvaluatedByUL).
WARNING
CUTAWAY VIEW
INCORRECT CORRECT
wall
plate
wall
plate
plaster/
dry wall
plaster/
dry wall
concrete
concrete
1-2
Visit the Peerless Web Site at www.peerlessmounts.com
8 of 13
3
2
Slide adjustment tube (B) into wall arm (A) and adjust to the desired projector throw distance as shown. Using two
separate slots on wall arm (A),lockpositionusingtwoM5x10mmscrews(D) as shown below.
B
A
Assembly of Adjustment Tube
ISSUED: 11-18-10 SHEET #: 125-9159-1
Installing Precision Gear Projector Mount
Installing PRG projector mount to wall arm assembly: Attach precision gear projector mount (J) to
adjustment tube (B) using two 1/4-20 socket pin screws (H)andtwoatwashers(I)
as shown in Figure 3.1.
g. 3.1
D
ARROW
INDICATES
FRONTOF
PROJECTOR
H
I
J
MAXIMUM EXTENSION SHOWN
Note: Securing adjustment tube (B) into wall arm (A)requirestwoslots.
TWO SCREWS (D)
REQUIRED THROUGH
TWO SLOTS
B
A
B
Visit the Peerless Web Site at www.peerlessmounts.com
9 of 13
4
ISSUED: 11-18-10 SHEET #: 125-9159-1
Routing Cables
Routing Cables through precision gear projector mount (J) and wall arm assembly: Guide
projector cables into openings in projector mount and wall arm assembly as shown below.
Insert tube cap (F) into end of adjustment tube (B).
J
F
PROJECTOR CABLES
Note:Cablesmustberemovedfromprojectorbeforeroutingthroughwallarm.
PROJECTOR CABLES
B
A
Model Configuration Page
EX525ST 1 10
TW610ST 2 11
TX610ST 2 11
5
Checkyourprojectorforthecorrespondingcongurationandpage.
Visit the Peerless Web Site at www.peerlessmounts.com
10 of 13
ISSUED: 11-18-10 SHEET #: 125-9159-1
6
Conguration 1
Attach connection block (S) to adapter plate (N)
usingtwo#10-32x3/8"serratedsocketpinscrews(O)
and.219IDx.5ODx.125"spacers(P).
Note:Whenattachingextensionbrackets(T) be sure to
keep fasteners in the center of the slot.
POSITIONSCREW,
SPACERANDWASHER
INCENTEROFSLOT
CORRECT
INCORRECT
T
T
Attachfourextensionbrackets(T) to main adapter plate (N)usingtwoM4x8mmserratedsocketpinscrews(V),
twoM4x16mmsocketpinserratedwasherheadscrews(Y),andtwo.198x.313x.375"spacers(X).
Attachextensionbrackets(T)toprojectorusingfour.219IDx.5ODx.125"spacers(P),two#8atwashers(R),
twoM4x16mmsocketpinserratedwasherheadscrews(Y),andtwoM4x12mmknobs(W).
Tighten using 4mm security allen wrench (C).
7
FRONTOF
PROJECTOR FRONTOFPROJECTOR
T
MOUNTPLATE(N)USINGMOUNTINGHOLESASSHOWN
P
Y
P
W
X
V
R
Y
N
SHOULDER
FRONTOF
PROJECTOR
N
S
O
P
Visit the Peerless Web Site at www.peerlessmounts.com
11 of 13
ISSUED: 11-18-10 SHEET #: 125-9159-1
7
Conguration 2
Attach adapter plate (N)toprojectorusingtwo.219IDx.5ODx.125"spacers(P),two
M3x12mmsocketpinserratedwasherheadscrews(U),one.198x.313x.375"spacer(X),andone
M3x20mmknob(Z). Tighten using 2mm security allen wrench (AA).
FRONTOF
PROJECTOR
FRONTOFPROJECTOR
N
MOUNTPLATE(N)USINGMOUNTINGHOLESASSHOWN
6
Attach connection block (S) to adapter plate (N) using
two#10-32x3/8"serratedsocketpinscrews(O) and
.219IDx.5ODx.125"spacers(P).
SHOULDER
FRONTOF
PROJECTOR
N
S
O
P
P
U
Z
X
Visit the Peerless Web Site at www.peerlessmounts.com
12 of 13
ISSUED: 11-18-10 SHEET #: 125-9159-1
Slide connection block (S) through precision gear projector mount (J) as shown.
Tightencaptivescrewtosecureprecisiongearprojectormount(J).
• Donotliftmoreweightthanyoucanhandle.Useadditionalmanpowerormechanicalliftingequipmenttosafely
handle placement of the screen.
WARNING
Attaching Adapter Plate to Projector Mount
S
J
FRONTOFMOUNT
CAPTIVE SCREW
ARROW
INDICATES
FRONTOF
MOUNT
8
IMPORTANT:Forsecurityinstallations,insertone#10-32x1/4"socketpinscrew(Q) through
precision gear projector mount (J) and into connection block (S) as shown. Tighten screw using
4mm security allen wrench (C).
J
Q
9
S
Visit the Peerless Web Site at www.peerlessmounts.com
13 of 13
ISSUED: 11-18-10 SHEET #: 125-9159-1
©2010,PeerlessIndustries,Inc.Allrightsreserved.
Allotherbrandandproductnamesaretrademarksorregisteredtrademarksoftheirrespectiveowners.
Toaccesstheprojectorlightbulb,removetwoM4x12mmknobs(W)attachedtofrontextensionbracketsas
shown below.
NOTE:Don’tdiscardtwo.219IDx.5ODx.125”spacers(P).
10
Accessing Projector Light Bulb
Conguration 1
Conguration 2
Z
W
PROJECTOR
PROJECTOR
FRONTOF
PROJECTOR
FRONTOF
PROJECTOR
Toaccesstheprojectorlightbulb,removeoneM3x20mmknob(Z)attachedtofrontextensionbracketsasshown
below.
NOTE:Don’tdiscard.219IDx.5ODx.125”spacers(P).
10
/