Thinklogical Velocitydvi System-3 A/V Pro Quick start guide

Thinklogical
Brand
Thinklogical
Model
Velocitydvi System-3 A/V Pro
Type
Quick start guide
Copyright © 2010. All rights reserved. Printed in the U.S.A. All trademarks and service marks are the property of their respective owners.
QUICK START GUIDE
4
Visit us online at www.thinklogical.com for more product information, current updates
and the complete line of Thinklogical™ products.
Receiver
CPU
Power Supply
Digital Video & Balanced Audio Extension System
The Velocitydvi Digital Video/Audio Extension System-3 A/V Pro from Thinklogical™ permits the placement of a digital monitor or projector and audio devices up to 1000 meters (3280 feet) away
from a controlling computer and audio sources without loss of resolution. Each system consists of a transmitter and a receiver connected by multi-mode fiber optic cable(s). Dual fiber is used for
some DDC modes to provide communications to and from the transmitter. The receiver unit provides an interface to the display and audio devices. Installation is plug-and-play and no adjustments are
necessary.
Each of the Thinklogical™ DVI A/V Pro Extension Systems is designed for high resolution video and audio extension applications such as remote projection centers, theaters and assembly halls,
and for secure computer installations. It is now possible to position the monitor or projector in any setting from office to lecture hall to boardroom while keeping the computer secure in a remote,
controlled location. All physical connections to the product use industry-standard connectors.
The Status LEDs on the Tx and Rx units are used to indicate the status of
connections to the extender:
Tx Status LED
· Green = Fiber L2 is connected and a good link is established.
· Orange = Local Static Mode selected and no fiber link from Rx to Tx (L2 is not
connected) or both DDC mode buttons are held down and the unit is waiting
to reload the default DDC table.
· Red Flashing = No Fiber Link from Rx to Tx (Not available in Local Static
mode.)
Rx Status LED
· Green = Good Link and DVI device connected to primary port (port on left in
the diagram below).
· Orange = No DVI device connected to primary port.
· Red Flashing = No Fiber Link from Tx to Rx (L1 is not connected).
Contents
Upon receiving your Thinklogical™
Velocitydvi-3 AV Pro Extender System, you
should find the following items:
· DVI Extender Transmitter
· DVI Extender Receiver
· DVI-D Male to DVI-D Male Cable,
2 Meter (CBL00009-002MR)
· DB9M to DB9F (CBL000017-006FR)
· Two Universal AC Power Adapters
(PWR-000033-R)
· Product Manual CD
STEP 4: Connect your fiber optic cable, up to 1000 meters (available through
Thinklogical™) between the Transmitter and Receiver Units. Do not kink or pinch
the cable and be sure to keep all bend radii to no less than 3 inches.
3
STEP 3: Connect the Ground
Lug to chassis ground. Connect
the supplied AC Adapter (PWR-
000033-R) to the Receiver and
plug it in to a standard AC source.
6
STEP 1:
Connect one end of a DVI-D Male to Male Cable to the primary viewing device.
Connect the other end of the cable to the Primary (left) Receiver DVI-D
connector. A second device can also be installed to the right- side, secondary
port using a similar DVI-D Male to Male cable. If using only one device, it must be
connected to the Primary Port. Turn ON the DVI video device(s).
STEP 5: Connect the Ground Lug
to chassis ground. Connect the
supplied AC Adapter (PWR-
000033-R) to the
Transmitter unit and
plug it in to a
standard AC source.
Projector
Acquire Button
· Used to initiate DDC collection. Works with all modes except Pass-Thru.
Must be pressed after switching between DDC modes.
Select Button
· Used to select the DDC mode. The modes will cycle through Remote
Dynamic, Remote Static, Pass-Thru and Local Static.
Both Buttons held 5 seconds
· Holding both buttons for 5 seconds will reload the default DDC table into
the Tx and switch to Remote Static mode.
Fiber-optic
cable ports.
GND
The Primary Port on the Rx is used for DDC. The Secondary Port
carries video data only.
Primary DVI Port DDC
Optional Secondary DVI Port
1
Power Supply
When lit, the solid
green LED indicates
that power is applied.
Transmitter
◄ Line IN Left
Line OUT Right►
◄ Line IN Left
Line OUT Left► 2STEP 2: Connect your
audio Lines IN (R & L)
and Lines OUT (R & L)
to the appropriate
Receiver ports.
DVI-D Connector 1 DVI-D Connector 2
STEP 6: Connect one end
of a DVI-D Male to Male
Cable to the Video Source
(DVI-D video card). Connect
the other end to the Transmitter’s
DVI from CPU connector. A local display may
also be connected using the supplied 2 meter DVI-
D Male to Male Cable (CBL-000009-002MR).
VELOCITY-3AV_Pro_Quick_Start_Rev_A
PHONE: 1-800-291-3211
WEBSITE: www.thinklogical.com
EMAIL: [email protected]
DB9 Serial Connector
(Tx: Female, Rx: Male)
Velocity
Transmitter
The Future of Access and Control
Digital Video Extension System – 3A/N+
L2 ► Data
L1 ◄ Video/Data
Status
5VDC
Power
FOL
TX
RX
LNK/ACT
DDC Mode
Acquire
LCL
L2 ◄ Data
L1 ► Video/Data
Secondary
DVI Port
Local Monitor
7
Velocitydvi-3 A/V Pro
Connect L1 to L1 and L2 to L2: Optical Fibers
available with ST-, SC- or LC-type connectors.
L1 L2
L1: Data Tx to Rx and Video
L2: Data Rx to Tx
STEP 7: Connect the Lines IN (R & L) and Lines OUT (R & L) audio cables to the appropriate
Transmitter ports. Ensure that all the devices are turned on and all system functions are
operating properly.
GREEN
GREEN
ORANGE
LCL REM DDC MODE DESCRIPTION
REMOTE
DYNAMIC
REMOTE
STATIC
PASS-
THRU
LOCAL
STATIC
EDID READ FROM REMOTE DISPLAY
AND UPDATED EACH TIME REMOTE
DISPLAY CHANGES.
EDID READ FROM REMOTE DISPLAY
WHEN ACQUIRE BUTTON IS PRESSED.
ACTS AS A DIRECT CONNECTION
BETWEEN CPU AND DISPLAY. NO
EMULATION IS PERFORMED.
EDID READ FROM LOCAL DISPLAY
WHEN ACQUIRE BUTTON IS PRESSED.
OFF GREEN
GREEN
GREEN
ORANGE
5+12VDC In
Available with 3-position Removable Terminal Blocks (above) or ¼” TRS Jacks (below).
Receiver
DVI To Display
DVI to Display
DDC
The Future of access and Control
tm
L2 ◄ Data
Digital Video Extension System – 3 A/V Pro
with Balanced Audio
L1 ► Video/Data
Serial
Power
12VDC
+
_
Status
Powered by
MRTS Technology
Velocitydvi
Left
Out
Right
Out
Left
In
Right
In
Audio Line
DDC Mode
LCL REM
Acquire
Select
Transmitter
DVI
from CPU
DVI to
Local Display
The Future of access and Control
tm
L1 ◄ Video/Data
Digital Video Extension System – 3 A/V Pro
with Balanced Audio
L2 ► Data
Serial
Power
12VDC
+
_
Status
Powered by
MRTS Technology
Velocitydvi
Left
Out
Right
Out
Left
In
Right
In
Audio Line
DDC Mode
LCL REM
Acquire
Select
◄ Line IN Right
◄ Line IN Right
Line OUT Right►
Line OUT Left►
Audio IN
Audio OUT
Microphone
Preamp
+
-
+
-
sleeve (GND) ring (-)
tip (+)strain relief
Line IN/
OUT
polarity:
  • Page 1 1

Thinklogical Velocitydvi System-3 A/V Pro Quick start guide

Thinklogical
Brand
Thinklogical
Model
Velocitydvi System-3 A/V Pro
Type
Quick start guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents