Thinklogical VelocityKVM-8 Quick start guide

Brand: Thinklogical

Model: VelocityKVM-8

Type: Quick start guide

100-240V-,0.5A,50/60 Hz T 2A,250VAC

CAUTION!Replace with same type and rating fuse.

CNTRL

LINE OUT HOST

USB HID

PWR FOL

USB 2.0

SER IAL PORT

Local

Display

DVI OUT DDC DVI OUT

STEP 6: A DVI-D dual-link cable (CBL000023-

002MR) is included. Connect it to the CPU DVI

Video Card and the other end to the VelocityKVM

Transmitter’s Dual-Link DVI IN connector.

STEP 7: (Optional) Connect your local

monitor cable (not included) to the Dual-

Link DVI OUT connector on the

VelocityKVM Transmitter.

UPDATES

DEV

DUAL-LINK DVI OUT

DUAL-LINK DVI IN

SER IAL PORT

LINE IN

MIC OUT HID

LOCAL FROM CPU

USB1.1

USB HID

HOST

CNTRL

CAUTION! Replace with same type and rating fuse.

100-240V-,0.5A, 50/60 Hz T 2A ,250VAC

CLINK

PWR

CP FOL

USB 2.0

Audio OUT

Audio IN

PS/2 Keyboard

PS/2 Mouse

USB HID (Kybd/Mouse)

USB 1.1 (Kybd/Mouse)

DUAL

LINK

DVI

DUAL-LINK

DVI OUT

DVI

Display

Out

DVI

Display

Out DDC*

VelocityKVM-8 Transmitter

VelocityKVM-8 Receiver

STEP 8: If desired, connect your local

keyboard and mouse by inserting the PS/2 or

USB HID connectors into the VelocityKVM

Transmitter’s local devices receptacles.

STEP 4: Connect your Multi-

Mode Fiber Optic cables

between the Transmitter and

Receiver units as shown.

(1 to 3 Single-Mode fibers can

also be used, depending on the

model and required fiber

length.)

L1: Data Tx to Rx and Video 1

Primary

L2: Data Rx to Tx

L3: Video 1 Secondary

STEP 5: Connect

your KVM devices

to the CPU using

the cables supplied

in KIT-000005-R.

STEP 3: Turn the

Receiver unit ON.

STEP 2: Connect your desktop devices

(monitors, keyboard, mouse, etc.) to the

Receiver using standard cables.

The Thinklogical™Velocitykvm-8 Multi-Mode Fiber Optic System consists of a transmitter unit and a receiver unit connected by three multi-mode fiber

optic cables (or by one to three optional single-mode fibers). The transmitter unit connects to the computer with standard cables and the receiver unit

provides connections to the user interface devices. The Velocitykvm-8 supports PS/2, full duplex stereo audio, serial (RS-232), USB 1.0 (HID) device

ports, USB 1.1 and USB 2.0 (high speed up to 480Mbps).

Note: In order to

avoid possible exposure

to laser energy, it is good

practice to attach the

fiber optic cables prior to

applying power to the

unit.

Note: Be sure to

leave adequate ventilation

space on both sides of

the units (2” minimum),

especially if the units are

being stacked

CONTENTS

Upon receiving your Thinklogical™

Velocitykvm-8 Extender, you should

find the following items:

· VelocityKVM Extender Transmitter

· VelocityKVM Extender Receiver

· 2 AC power cords, PWR-000006-R

(International connections may differ.)

· VelocityKVM Extender Cables:

1DVI-D Male Dual-link Cable, 2 meters, CBL000023-002MR

1 Cable Kit (8 six ft. peripheral cables.) KIT-000005-R

All physical connections to the product use industry-standard connectors.

QUICK START GUIDE

PS/2 Connector USB HID Connector

STEP 10: Turn on the

Source (CPU) last. Verify

that all system features are

functioning properly.

Visit us online at www.thinklogical.com for more

product information, current updates and the

complete line of Thinklogical products.

MIC IN

Velocitykvm-8

Multi-Mode Fiber Extension System –Dual-link DVI

L2 L3

8 Mounting bracket

screws

Single Head Single Link

Velocitykvm-8

Fiber Optic Transmitter

2 Mounting bracket screws

in four places.

RACK-MOUNT OR DESK-TOP

OPTIONS: Like all Thinklogical™

KVM extenders, the VelocityKVM-8

can be mounted in a standard EIA 19"

rack or on a shelf or desk-top.

Each mounting bracket is

secured by four screws and

can be safely removed from

the transmitter or receiver

unit for desk-top mounting.

VEL-U00M08-SCTX

VEL-U00M08-SCRX

STEP 9: Turn the

Transmitter unit ON.

Audio IN►

PS/2

Keyboard/

Mouse

USB HID

USB 1.1

▲

Audio

OUT 5

VELOCITY-8_Quick_Start_Rev_C

L2L3

L1 L2

USB or PS2

STEP 1: Ensure that the POWER ON/OFF switch is

in the OFF position (0) on both the Tx and Rx units.

Connect the supplied AC Power Cords to both units

and plug them into a standard AC supply. LEAVE

BOTH SWITCHES IN THE OFF POSITION.

* Display Data Channel: Communicates supported

display modes to the CPU.

This is the PRIMARY DISPLAY and should be

used when only one monitor is connected.

When 2 monitors are used, the display modes of

both DVI outputs will follow the DDC of the primary

monitor.

PHONE: 1-800-291-3211

WEBSITE: www.thinklogical.com

EMAIL: [email protected]

Thinklogical VelocityKVM-8 Quick start guide

Thinklogical VelocityKVM-8 Quick start guide

Thinklogical VelocityKVM-8 Quick start guide

Related papers

Other documents