SB03/06/19 Roofing
347424_ROF_0009_25863_0219_Tremco_6in_BURmesh
Signal Word: n/aPrincipal Display Panel: 12” Statement of Hazard: n/a
Other Cautionary Material (Back label): .0682”Other Cautionary Material: n/a
Net Wt: n/aOther Cautionary Material (Address): .0641”
All dimensions are based on the measurements within the label at 100% actual size.
BURmesh
REINFORCEMENT FABRIC
®
6" x 300'
BURMESH
347424
TRUSTED ROOFING SOLUTIONS SINCE 1928
VINYL COATED,
WOVEN GLASS MESH
FLEXIBLE MESH
STRENGTHENS
ROOF REPAIR
COLOR PROVIDES
VISUAL CONTRAST
FOR ADEQUATE
TOPCOAT COVERAGE
BONDED GLASS
MESH WILL NOT
ROT OR DECAY
BURmesh® is a non-shrinking, non-rotting, vinyl coated, woven glass mesh. The glass filaments are firmly bonded
together to prevent strands from unraveling during application. BURmesh provides excellent tensile strength for
reinforcing flashing seams, membrane laps, or other roof system details. BURmesh can conform to irregular
surfaces because of its high degree of flexibility. The open weave design of BURmesh facilitates quick and uniform
embedment in Alumanation 301, Alumanation 101, mastics and asphalt based products.
DIRECTIONS
Surface Preparation: Surface must be clean and properly prepped per instructions on mastic or asphalt based
product being used with BURmesh. Application: Cut BURmesh to appropriate size. Apply a full coverage of the
specified roofing mastic or adhesive. Set BURmesh into the freshly applied material and apply pressure with a
brush or trowel to assure complete adhesion. If specified, apply additional courses of BURmesh and
mastic/adhesive. Apply a top course of mastic in a full coverage to completely cover the BURmesh. When repairing
blisters which have been cut open, or when sealing splits which extend through built-up roof membrane, use two
plies of BURmesh embedded between applications of Tremco mastics. Limitations: Not for application with hot
applied asphalt adhesives.
Limited Product Warranty: Should this product fail due to a defect, unless expressly agreed otherwise by Tremco
in writing, purchaser’s sole and exclusive remedy is that Tremco Incorporated will, at its option, either refund to the
purchaser the amount paid for the product, or furnish at its expense sucient product to restore a protective
condition to the aected areas. Proof of purchase must be provided. At its discretion, Tremco may require
inspection of the aected areas by a Tremco representative. Contact Tremco Product Support at 1-800-852-6013.
Refer to product number and batch code. Please visit www.tremcoroofing.com for further information regarding
additional warranties that may be available for your roofing system. NO OTHER WARRANTY OR GUARANTEE OF
ANY KIND IS MADE BY TREMCO, EXPRESS OR IMPLIED, STATUTORY, BY OPERATION OF LAW, OR OTHERWISE,
INCLUDING BUT NOT LIMITED TO MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
WARNING: Cancer – www.P65Warnings.ca.gov
BURmesh® es una malla de fibra vidrio tejida con recubrimiento de vinilo que no encoge ni se
pudre. Las fibras de vidrio están unidas con firmeza para evitar que se zafen las hebras durante
la aplicación. BURmesh proporciona excelente resistencia a la tracción para reforzar las uniones
de tapajuntas, capas de membrana u otros detalles de los sistemas de techos. BURmesh se
ajusta a las superficies irregulares debido a su alto grado de flexibilidad. El diseño de tejido
abierto de BURmesh facilita la incrustación rápida y uniforme en masillas Alumanation 301,
Alumanation 101 y en productos a base de asfalto.
INSTRUCCIONES
Preparación de la Superficie: La superficie debe estar limpia y bien preparada de acuerdo con
las instrucciones del producto de inserción.
Aplicación: Corte la malla BURmesh al tamaño adecuado. Aplique adhesivo o masilla
específicos para techos de forma que cubra por completo. Coloque la malla BURmesh sobre el
material recién aplicado y presione con una llana seca para asegurar la adhesión completa. Si
está indicado, aplique capas adicionales de BURmesh y masilla o adhesivo. Aplique una capa
final de masilla en toda el área para cubrir la malla BURmesh. Cuando repare ampollas que
hayan sido cortadas o cuando selle hendiduras que se extienden a través de la membrana del
techo, utilice dos capas de BURmesh insertadas entre aplicaciones de masillas Tremco.
Limitaciones: No puede aplicarse sobre adhesivos asfálticos que se coloquen en caliente.
ADVERTENCIA: Cáncer – www.P65Warnings.ca.gov
25863 0219
347424 TREMCO BURMESH
1
-
800
-
852
-
6013
I
www.tremcoroofing.com
3735 Green Road, Beachwood, Ohio 44122
©2019 Tremco Roofing and Building Maintenance. All Rights Reserved.
1
Rust-Oleum 347433 User manual
Lanco FM995-15 User manual
Charlotte Pipe CTS 02300 1000HD Installation guide
Continental Materials STR1281 Operating instructions
MULTIBETON MGA-40 User manual
DensShield 855000 Installation guide
HTP Phoenix Solar Water Heater User manual
Henry HE208R361 User manual
