Tremco 346557 is a high-performance 100% acrylic elastomeric roof sealant designed for use on a variety of roofing and wall substrates. It exhibits excellent weatherability, ultraviolet resistance, and waterproofing protection at seams, fasteners, and penetrations. It can also be used to fill small to medium cracks and spalling areas on concrete, masonry, or stucco type wall surfaces.
Tremco 346557 is a high-performance 100% acrylic elastomeric roof sealant designed for use on a variety of roofing and wall substrates. It exhibits excellent weatherability, ultraviolet resistance, and waterproofing protection at seams, fasteners, and penetrations. It can also be used to fill small to medium cracks and spalling areas on concrete, masonry, or stucco type wall surfaces.
SOLARGARD
SEALER
®
100% ACRYLIC
Sellador acrílico solargard
sellador elastomérico blanco
WHITE
ELASTOMERIC
ROOF SEALANT
USE ON: Rolled Roofing, Built-Up
Roofs, Concrete & Metal Roofs
NO BLEED
THROUGH
STOPS
ROOF
LEAKS
SEALS LEAKS ON DRY
OR DAMP SURFACES
COMPATIBLE WITH
SOLARGARD
®
ELASTOMERIC
ROOF COATINGS
EXTREME FLEXIBILITY
PREVENTS CRACKS & TEARS
WHITE
0.9 GALLON 3.4 LITERS
SOLARGARD ACRYLIC SEALER
346557
TRUSTED ROOFING SOLUTIONS SINCE 1928
Acrylic Elastomeric
Roof Sealer can be
applied to:
• Metal roofs
• Asphalt &
modified bitumen
• Most single-ply roofs
Application:
• Apply by brush or trowel
See other cautions on the back panel.
SOLARGARD ACRYLIC SEALER is a high solids, acrylic elastomeric sealer designated for use on a
variety of roofing and wall substrates. SOLARGARD ACRYLIC SEALER exhibits excellent weather-
ability and ultraviolet resistance. SOLARGARD ACRYLIC SEALER provides waterproofing protection
at seams, fasteners, and penetrations. All cracks, seams, or penetrations greater than 1/8” must be
reinforced using TREMCO PERMAFAB in a three-course application. SOLARGARD ACRYLIC SEALER
may also be used to fill small to medium cracks and small spalling areas on concrete, masonry, or
stucco type wall surfaces.
DIRECTIONS
SURFACE PREPARATION: All surfaces must be clean, dry, and free from dirt, debris, grease, oil, loose
paint or coating, and rust which could prevent proper adhesion. All rusted areas must be primed
prior to application of SOLARGARD ACRYLIC SEALER. If surface was previously coated, please
contact Tremco for adhesion check and surface preparation recommendations.
APPLICATION: Apply SOLARGARD ACRYLIC SEALER using brush, trowel or putty knife. Allow to cure
24-48 hours prior to the application of Tremco’s SOLARGARD Coating Systems.
COVERAGE: SOLARGARD ACRYLIC SEALER will cover approximately 50’-75’ at 1/8” thickness, at a
width of 4”-6”. Approximately 25’-40’ when using in a three course application using PERMAFAB
reinforcing fabric. Will encapsulate approximately 150-200 fasteners per gallon.
DRY TIME: 24-48 hours
CLEAN UP: Water
LIMITATIONS: Application temperature shall be a minimum of 45°F dry and rising. Protect from freezing
during shipment and storage. Not intended for immersion service over coal tar, silicone-based
products, or below grade. Do not apply when rain is imminent. Do not apply greater than 50 wet mils.
PRECAUTIONS: Do not take internally. Use only with adequate ventilation. Do not breathe dust, vapors
or spray mist. Ensure fresh air entry during application and drying. Close container after each use. Avoid
contact with skin and eyes. Wash thoroughly after handling. First Aid: If you experience diculty in
breathing, leave area to obtain fresh air. If continued diculty is experienced, get medical assistance
immediately. In case of contact, immediately flush skin with soap and water and eyes with plenty of
water. If swallowed, get medical attention immediately. KEEP OUT OF REACH OF CHILDREN. For
emergency, call your physician, local poison control center or local emergency room. For product health
information, call: 1-800-852-6013.
WARNING: Cancer – www.P65Warnings.ca.gov.
Limited Product Warranty: Should this product fail due to a defect, unless expressly agreed otherwise
by Tremco in writing, purchaser’s sole and exclusive remedy is that Tremco Incorporated will, at its
option, either refund to the purchaser the amount paid for the product, or furnish at its expense
sucient product to restore a protective condition to the aected areas. Proof of purchase must be
provided. At its discretion, Tremco may require inspection of the aected areas by a Tremco representa-
tive. Contact Tremco Product Support at 1-800-852-6013. Refer to product number and batch code.
Please visit www.tremcoroofing.com for further information regarding additional warranties that may
be available for your roofing system. NO OTHER WARRANTY OR GUARANTEE OF ANY KIND IS MADE
BY TREMCO, EXPRESS OR IMPLIED, STATUTORY, BY OPERATION OF LAW, OR OTHERWISE, INCLUDING
BUT NOT LIMITED TO MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
Max VOC = <50 g/L
El sellador acrílico SOLARGARD ACRYLIC SEALER es un sellador acrílico con propiedades
elastómeras con alto contenido sólido indicado para el uso en una gran variedad de sustratos para
techos y paredes. El sellador acrílico SOLARGARD ACRYLIC SEALER presenta una excelente
resistencia a la intemperie y a la luz ultravioleta. El sellador acrílico SOLARGARD ACRYLIC SEALER
ofrece protección impermeable en las juntas, sujetadores y filtraciones. Todas las grietas, juntas o
filtraciones mayores a 1/8” deben reforzarse con una aplicación de tres pasos de PERMAFAB. El
sellador acrílico SOLARGARD ACRYLIC SEALER también puede utilizarse para rellenar grietas
pequeñas a medianas y en pequeñas áreas de descascaramiento en superficies laterales de
concreto, mampostería o estuco.
INSTRUCCIONES
PREPARACIÓN DE LA SUPERFICIE: Todas las superficies deben estar limpias, secas y libre de
suciedad, escombros, grasa, aceite, pintura o revestimiento suelto y óxido que pueda evitar la
correcta adhesión. Colocar un imprimador en todas las áreas oxidadas antes de aplicar el sellador
acrílico SOLARGARD ACRYLIC SEALER. Si la superficie fue revestida previamente, comuníquese con
el Departamento Técnico para que le recomienden cómo prepararla y verificar la adhesión.
APLICACIÓN: Aplique el sellador acrílico SOLARGARD ACRYLIC SEALER con una brocha, llana o
espátula. Deje curar entre 24 a 48 horas antes de la aplicación de los sistemas de recubrimiento
Tremco’s SOLARGARD.
RENDIMIENTO: El sellador acrílico SOLARGARD ACRYLIC SEALER cubrirá aproximadamente 50’ a
75’ en 1/8” de espesor, en un ancho de 4” a 6”. Aproximadamente 25’ a 40’ si se usa en una
aplicación de tres pasos con una tela de refuerzo PERMAFAB. Encapsulará aproximadamente 150 a
200 sujetadores por galón.
TIEMPO DE SECADO: De 24 a 48 horas
LIMPIEZA: Agua
LIMITACIONES: La temperatura de aplicación será a un mínimo de secado de 45 °F o más. Evite el
congelamiento durante el envío y almacenamiento. No destinado para servicio de inmersión en
alquitrán, productos a base de silicona o menor grado. No lo aplique si va a llover. No aplique más
de 50 mils húmedos.
Garantía limitada del producto: En caso de que este producto falle debido a un defecto, a menos
que Tremco acuerde por escrito algo distinto, la única y exclusiva reparación del comprador es que
Tremco Incorporated, a su criterio, reembolse al comprador la cantidad pagada por el producto o
que le proporcione, a expensas suyas, suficiente producto para restaurar una condición de
protección en las áreas afectadas. Se debe proporcionar comprobante de compra. Tremco puede
pedir, a su discreción, que un representante de Tremco inspeccione las áreas afectadas.
Comuníquese con el Soporte técnico de Tremco al 1-800-852-6013. Indique el número del producto y
el código de lote. Visite Tremcoroofing.com para obtener más información relacionada con garantías
adicionales que puedan estar disponibles para sus techos. TREMCO NO OFRECE NINGUNA OTRA
GARANTÍA, DE NINGÚN TIPO, NI EXPLÍCITA NI IMPLÍCITA, ESTATUTARIA, POR LEY NI DE OTRA
ÍNDOLE, INCLUIDAS, ENTRE OTRAS, PARA LA COMERCIABILIDAD Y LA ADECUACIÓN PARA UN
PROPÓSITO ESPECÍFICO.
346557 SOLARGARD ACRYLIC SEALER
SB03/11/19 Roofing
346557_ROF_0007_25864_0219_Tremco_1Gal_SolarGardAcrylicSealer_White
Signal Word: .16”Principal Display Panel: 60” Statement of Hazard: .1167”
Other Cautionary Material (Back label): .0975”Other Cautionary Material: .1069”
Net Wt: .188”Other Cautionary Material (Address): .1023”
All dimensions are based on the measurements within the label at 100% actual size.
1
-
800
-
852
-
6013
I
www.tremcoroofing.com
3735 Green Road, Beachwood, Ohio 44122
©2019 Tremco Roofing and Building Maintenance. All Rights Reserved.
25864 0219
-
1
Tremco 346557 is a high-performance 100% acrylic elastomeric roof sealant designed for use on a variety of roofing and wall substrates. It exhibits excellent weatherability, ultraviolet resistance, and waterproofing protection at seams, fasteners, and penetrations. It can also be used to fill small to medium cracks and spalling areas on concrete, masonry, or stucco type wall surfaces.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
in other languages
- español: Tremco 346557 Manual de usuario
Related papers
Other documents
-
Gardner SK-7705-P Operating instructions
-
WHITE-KOTE SK-4401 Operating instructions
-
BLACK JACK 5228-1-20 Installation guide
-
-
ANViL ROOF-TEC 121401 Installation guide
-
Sika 7116130 Installation guide
-
Latex-ite 5060 User manual
-
-
Henry HE884004 Installation guide
-
