2. Winners Only
  3. BCA1001CK

Winners Only BCA1001CK Assembly Instructions

  • Hello! I'm your chat assistant. I have reviewed the assembly instructions for the WINNERS ONLY bed models BCA1001Q, BCA1001K, and BCA1001CK. This document includes a detailed parts list and step-by-step directions for assembling your new bed, including attaching the side rails, headboard, and slats with support legs. I'm ready to assist with any questions you may have about the assembly process or the components.
  • What should I do before unpacking assembly parts?
    What is recommended to do with hardware parts?
    Is it recommended to assemble this product alone?
    What type of screws should be used on BCA1001Q?
    What type of screws should be used on BCA1001K/CK?
ASSEMBLY INSTRUCTIONS
BCA(BCU)1001Q / K / CK
1.Pick up one side rail and insert the hook into the post slot of the footboard.
2.Repeat step 1 to attach the other side rail.
3.Follow steps 1 & 2 to attach the headboard.
4.Attach slat support legs to slat as indicated in diagram, with metal insert
neck facing up.
5.Lay 4 slats across bed as indicated in diagram. Align the pre-drilled holes
of the wooden slats with the pre-drilled holes of the bed side rail. Secure by
using 1-1/4" sharp end screws.
1-3/4" Sharp End Screws 8 pcs
Slats 4 pcs
Slat Support Legs 8 pcs
5
4
3
Bottom of the slat
Top of the slat
Metal insert
neck facing up.
Caution : Please read instructions thoroughly before unpacking assembly parts. Sharp, exposed staple tips can cause injury,
therefore, for your protection, please remove any exposed staples used in packing.
Please keep all hardware parts out of the reach of children.
1. We recommend that you should assemble this product with the assistance of another person;this will make assembly easier,
and will help to eliminate damage to the product or injury to persons during assembly.
2. Be sure to check all packing materials carefully for small parts that may have come loose inside the carton during shipment.
3. Please do not over tighten screws or bolts.
4. Please put all parts on a non-abrasive floor before assembly, and follow the assembly steps to assemble your newly purchased
product correctly and efficiently.
Insert on the outside slot.
1-1/4" Sharp End Screws 8 pcs
Slats 4 pcs
Slat Support Legs 4 pcs
Parts List (included in BCA1001Q) Parts List (included in BCA1001K/CK)
BCA(BCU)1001Q BCA(BCU)1001K
BCA(BCU)1001CK
BCA(BCU)1001QH\KH\CKH
ASSEMBLY INSTRUCTION
Turn the headboard over in order to assemble the legs. Insert
the parts (1),(2) and (3) through the hole of the leg on the back
of the headboard. Repeat the step for the other side.
6PCS 5/16" Washer
6PCS 5/16" Spring Washer
6PCS 5/16"x1-1/2" Machine Bolts
31
2
x3-1-1/2"L
Back
Inside Outside
InsideOutside
The front side
of left leg
The front side
of right leg
R
R
L
L
Caution : Please read instructions thoroughly before unpacking assembly parts. Sharp, exposed staple tips can cause
injury, therefore, for your protection, please remove any exposed staples used in packing.
Please keep all hardware parts out of the reach of children.
1. We recommend that you should assemble this product with the assistance of another person;this will make assembly easier,
and will help to eliminate damage to the product or injury to persons during assembly.
2. Be sure to check all packing materials carefully for small parts that may have come loose inside the carton during shipment.
3. Please do not over tighten screws or bolts.
4. Please put all parts on a non-abrasive floor before assembly, and follow the assembly steps to assemble your newly purchased
product correctly and efficiently.
/