GVI Security auto IP NRD-213M Quick start guide

Type
Quick start guide
NID-213M/NRD-213M
2 Megapixel, H.264 IP Mini-dome Camera
QUICK START GUIDE
2
1. Review Package Contents
2. Make Connection To Camera
Connect the camera to the network using a shielded network cable (CAT5e / CAT6)
3. Adjust Camera Position
Designation Description
1 Reset Button Restore to default setting; press the button with a proper tool
2 Lens Rotate the lens right/left to adjust focus
3 Focus Fixed Screw Loosen the screw to adjust the lens
4 Tilt Fixed Screw Loosen the screw to adjust tilt angle
GVI Security Toll Free: 888-595-2288 • Fax: 972-245-7333
This product specifications and manual are also available in pdf format at www.gviss.com
The information is subject to change without notice v1.20.11
Indoor Camera/
Rugged Camera (with Cable)
Self-tapping
screws (x3)
Plastic Anchors
(x3)
Security Screw
(x1)
Security Torx Quick Guide CD
3
4. Assign an IP Address
Most networks today have a DHCP server that automatically assigns IP addresses to connected devices.
If your network does not have a DHCP server the autoIP camera will use 192.168.0.250 as the default IP
address.
The autoIP Discovery Tool can be used to assign a new IP address. The tool is available on the CD
supplied with this product or it can be downloaded from http://www.gviss.com/support/ip_support.php.
NOTE: The computer running the autoIP Discovery Tool must be on the
same network segment (physical subnet) as the autoIP cameras.
Verify that the autoIP cameras are connected to the network, and
that the power has been applied.
• Open the autoIP Discovery Tool
Click “Device Search” to list all of the autoIP cameras on the
network.
Right click on the desired autoIP camera and select “Network
Setup” to adjust the network settings.
GVI Security Toll Free: 888-595-2288 • Fax: 972-245-7333
This product specifications and manual are also available in pdf format at www.gviss.com
The information is subject to change without notice v1.20.11
4
5. Adjust Internet Browser And ActiveX Settings
ActiveX Controls and Plug-ins Settings Internet Security Level
Step 1: Start the Internet Explorer (IE).
Step 2: Select <Tools> from the main
menu of the browser. Then Click
<Internet Options>.
Step 3: Click the <Security> tab and
select “Internet”, and click
<Custom level> to change ActiveX
settings.
Step 4: Set ActiveX controls and plug-ins”
items to <Prompt> or <Enable>.
Step 1: Start the IE.
Step 2: Select <Tools> from the main menu of
the browser. Then Click <Internet
Options>.
Step 3: Click the <Security> tab and select
“Internet.
Step 4: Down the page, press “Default Level”
and click OK” to confirm the setting.
Close the browser window, and open a
new one later for accessing the camera.
6. Log In To The Camera
Login ID & Password
Key in the camera’s IP address within the URL bar of your Web
browser window and press “Enter.
Enter the default user name (Admin) and password (1234) as
prompted. Note that the user name is case sensitive.
Install the ActiveX control
After connecting to the camera, the request for installing the
ActiveX control will appear just below the URL bar.
Right Click on the information bar, and press “Install ActiveX
Control”.
Follow on the screen instructions until the installation of the
ActiveX controls are completed.
GVI Security Toll Free: 888-595-2288 • Fax: 972-245-7333
This product specifications and manual are also available in pdf format at www.gviss.com
The information is subject to change without notice v1.20.11
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

GVI Security auto IP NRD-213M Quick start guide

Type
Quick start guide

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI