Screen Innovations Solo 3 Indoor Installation guide

Solo 3

Indoor – 575/675 Flush

Method 2:

Material Only

Installation Instructions

INSTALLERS: PLEASE LEAVE THIS MANUAL WITH THE OWNER.

Doc. #400185 | v. 1.0 | 4 November 2022

Screen Innovations warrants its products, to the original purchaser only, to be free from defects in materials

and workmanship for a period of one (1) year from the date of purchase by the original purchaser provided

they are properly operated according to Screen Innovations' instructions and are not damaged due to improper

handling or treatment after shipment from the factory.

This warranty does not apply to equipment showing evidence of misuse, abuse, or accidental damage, or

which has been tampered with or repaired by a person other than authorized Screen Innovations personnel.

Screen Innovations’ sole obligation under this warranty shall be to repair or to replace (at Screen Innovations’

option) the defective part of the merchandise. Returns for service should be made to your Screen Innovations'

dealer. If it is necessary for the dealer to return the screen or part to Screen Innovations, transportation

expenses to and from Screen Innovations are payable by the purchaser and Screen Innovations is not

responsible for damage in shipment. To protect yourself against damage or loss in transit, insure the product

and prepay all transportation expenses.

This warranty is in lieu of all other warranties, express or implied, including warranties as to tness for use

and merchant ability. Any implied warranties of tness for use, or merchantability, that may be mandated by

statute or rule of law are limited to the one (1) year warranty period. This warranty gives you specic legal

rights, and you may also have other rights, which vary from state-to-state. No liability is assumed for expenses

or damages resulting from interruption in operation of equipment, or for incidental, direct, or consequential

damages of any nature.

In the event that there is a defect in materials or workmanship of a Screen Innovations product, you may

contact our Sales Partners at 9715-B Burnet Road Suite 400, Austin, TX 78758, (512) 832-6939.

Important: this warranty shall not be valid and screen innovations shall not be bound by this warranty if the

product is not operated in accordance with screen innovations' written instructions.

Keep your sales receipt to prove the date of purchase and your original ownership.

Limited 1 year warranty

on Screen Innovations products

Technical Support: 512.832.6939 screeninnovations.com

Hours of Support: 7:30am – 5pm CST [email protected]

Please use this QR Code

to access the updated

installation instructions

and related documents.

Parts in the Box – Solo 3 575/675 – Flush – Material � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 4

Installation – Material Tube � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 5–7

Internal Cassette Wiring (24v DC) � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 8

Internal Cassette Wiring (110v/220v AC) � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 9

Finishing Touches – Flanges � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 10–11

– Fascia Door � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 12

Commisioning and Control Guide References � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 13

Removing and Replacing Moab � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � �14

TABLE OF CONTENTS

4

PARTS IN THE BOX – SOLO 3 575/675 – FLUSH – MATERIAL

Material Tube

Weight Bar

End Caps (2)

Red StrapsMoab

485 MOTORS

ONLY

485

DEVICES ONLY

3

8

UP

6

8

USER

ACT

MODES

1 2 3 4

485 BUS

8

6

5

1

&

IR REC

ACTIVE

L12

L11

L9

L15

L14

L13

L1

L3

L2

L4

L7

L8

302325

202311 (EXT)

202312 (INT)

VIEW

485

LIMIT

LOWER

LIMIT

MOTOR ROTATION

STANDARD REVERSE

9VDC

485

DC MOTOR

485 PAIRING

STOP

UPPER

IR REC

IR

LED

BOARD

SETTINGS

6

3

(T)

-

STOP

485 DEVICE &

DRY CONTACT PORT

3.5mm(1/8 in) mono (TS)

(S)

+

RJ45 RJ9

12-28VDC

DC POWER &

485 DATA PORT

DOWN

AC MOTOR

G D- D+ V- V+

3

6

2

4

5

7

8

1

V- V+

12-28VDC

D+

D-

G

12v TRIGGER PORT

PROG

BUTTONS

DOWN

D O W N

485 NETWORK

MV

STOP

ON

LED1

S4

S3

S2

LED15

LED14

LED13

LED12

LED11

LED9

LED8

LED7

LED4

LED3

LED2

IC3

5

INSTALLATION – MATERIAL TUBE

The cassette will resemble this drawing when ush

mounted. Refer to the Solo 3 Indoor 575/675 Flush

installation instructions paired with the cassette unit.

NOTE: These instructions detail the steps following the mounting and placement of the cassette.

Release the weight bar; for further instruction, refer to steps 1–3 on page 10–12 of the main

Solo 3 Indoor 575/675 Flush installation instructions.

1

6

INSTALLATION – MATERIAL TUBE

Remove both of the silver safety screws from each side of the mounting plates.

2

Attach the magnetic endcaps to the weight bar, keeping the material from folding or bending.

3

7

INSTALLATION – MATERIAL TUBE

Remove the material roll and slide it in with mounting plates on each end into the cassette. Each

end will “click” into place as the brackets engage.

Fasten the silver safety screws on the mounting plates to secure the material roll.

4

5

8

INTERNAL CASSETTE WIRING – 24V DC

To head end/

equipment connects

to bottom terminal

block of Moab

Light Grey –

24v Wire

Scan this QR code to review your wiring to determine the max. length of the wire on

the 3 options as shown below, or alternatively use this link:

https://si-website-les.s3.amazonaws.com/Downloads/Programming+Guides/

Shade/wire-topologies.pdf

Detailed Low Voltage Power and 485 Control Wiring (DC Motor)

24v DC Power Supply

RS485 Data+

RS485 Data-

RS485 Ground

From motor

1. Terminate the wires with the provided terminal block/ RJ45 as shown below.

Data cable from

motor connect

to top terminal

block of Moab

Motor Front View Motor Side View

5 conductor wire to head

end/equipment

Optional relocation of IR reciever

when removed from Moab

NOTE: Determine the wiring type of your project; for 110/220v AC, refer to the following page.

9

1. Terminate the wires with the provided terminal block/ RJ45 as shown below.

2. Make sure an appropriate junction box or power receptacle is located within 5ft of the

installation location.

The installer must follow all local electrical codes when connecting 110v AC power. A certied

electrician is required to connect pigtail power.

INTERNAL CASSETTE WIRING – 110V/220V AC

Pigtail

L (Black)

N (White)

(Green)

Cat5e

RJ45 Coupler

(used only when Moab has been

relocated to head end)

Length of the wire: 8.4’

From motor

RS485 (+) - White

RS485 (-) - Orange

-

Power 7v DC - Red

-

Ground - Brown

Pin 1

Pin 8

Detailed AC Pinouts

AC 110/220V - Flush 485

Motor Front View

Black – AC wire

Light Grey – 24v Wire

Dark grey – Motor Com Cable

To 110v AC

Conect power to the motor

by snapping the connector

Optional relocation of IR reciever

when removed from Moab

Data cable from motor

connect to top RJ45 of Moab

Motor Side View

Cat 5 /other wire to head

end/equipment

To 110v

AC

Data cable

to head end/

equipment

connects to

bottom RJ45/

terminal

block of Moab

10

INSTALLATION – FLANGES

1Rotate anges into the cassette.

2Identify the ange clip.

11

INSTALLATION – FLANGES

4

3

Place end (short) anges into the cassette and screw in to secure.

Use the ange clip to hook and secure the anges into the cassette.

12

Set the door into the cassette; the door will hook in by gravity.

INSTALLATION – FASCIA DOOR

13

Moab Commissioning and Integration Guide:

Scan the QR code, alternately use the link below to access

https://les.screeninnovations.com/Downloads/Installation+Instructions/Accessories/

moab-installation-instructions.pdf

COMMISSIONING GUIDE REFERENCE – MOAB

With each screen order, you will receive one of the following Control Guides which will walk you

through integrating with control system.

TRO.Y Installation Instructions (RS232, IP Control, third party Control system):

Scan the QR code, alternately use this link to access

https://les.screeninnovations.com/Downloads/Installation+Instructions/Connectivity/

troy-installation-instructions.pdf

LinkPro Z Installation Instructions (IP Control, third party Control system):

Scan the QR code, alternately use this link to access

https://les.screeninnovations.com/Downloads/Installation+Instructions/Connectivity/

LinkProZ-installation-instructions.pdf

CONTROLS GUIDE REFERENCE

Technical Support: 512.832.6939 screeninnovations.com

Hours of Support: 7:30am – 5pm CST [email protected]

Scan this QR Code to

access the updated

installation instruc-

tions and related

documents.

14

2

1

REMOVING AND REPLACING – MOAB

Remove the fascia door. Push cassette all the way to the anges and ceiling; ne tune as needed

with a mounting key.

Plug the motor power cable into the barrel connector, located within the cassette, to connect Moab

(see page 8 for power options).

The Moab board may be placed or removed from the internal PCB mounting plate by gently

shifting the entire board up to remove, down to reattach the four (4) standoffs.

If using low voltage, use the included DUOcoup to facilitate the wiring connections.

Upon reattachment, the board will tactically “click” and snap into place.

NOTE: If permanently removing/relocating Moab, refer to the External Wiring section of the

Moab instructions by scanning this QR code.

15

Screen Innovations

9715-B Burnet Rd, Suite 400 Austin, TX 78758

512.832.6939

www.screeninnovations.com

Doc. #400185 | v. 1.0 | 4 November 2022

Screen Innovations Solo 3 Indoor Installation guide

Screen Innovations Solo 3 Indoor Installation guide

Related papers

Other documents