PRODUCT SUPPORT | 800.927.2120 | WATERWORKS.COM PAGE 1 OF 6 | UPDATED ON 3.05.2020
STYLE No. BLS130, BLS14A, BLS14B, BLS14D,
BLS15C
Bond Low Profile Lavatory Faucet with Knob
Handles
STYLE No. BLS110, BLS12A, BLS12B, BLS12C,
BLS12D, BLS12E
Bond Low Profile Lavatory Faucet with Lever
Handles
INSTALLATION GUIDELINES
STYLE No. BLS110
Bond Solo Series Lavatory with Lever Handles
• STYLE No. BLS100
Bond Low Profile Lavatory Faucet (Less Handles)
• STYLE No. BLH010
Bond Solo Series Lever Handle
STYLE No. BLS12A
Bond Tandem Series Lavatory Faucet with Guilloche Lines
Lever Handles
• STYLE No. BLS100
Bond Low Profile Lavatory Faucet (Less Handles)
• STYLE No. BLH02A
Bond Tandem Series Guilloche Lines Lever Handle
STYLE No. BLS12B
Bond Tandem Series Lavatory Faucet with Two-Tone Lever
Handles
• STYLE No. BLS100
Bond Low Profile Lavatory Faucet (Less Handles)
• STYLE No. BLH02B
Bond Tandem Series Two-Tone Lever Handle
STYLE No. BLS12C
Bond Union Series Lavatory Faucet with Guilloche Link Lever
Handles
• STYLE No. BLS100
Bond Low Profile Lavatory Faucet (Less Handles)
• STYLE No. BLH02C
Bond Union Series Guilloche Link Lever Handle
STYLE No. BLS12D
Bond Union Series Lavatory Faucet with Enamel Guilloche
Lines Lever Handles
• STYLE No. BLS100
Bond Low Profile Lavatory Faucet (Less Handles)
• STYLE No. BLH02D
Bond Union Series Enamel Guilloche Lines Lever
Handle
STYLE No. BLS12E
Bond Union Series Lavatory Faucet Guilloche Pinstripe Lever
Handles
• STYLE No. BLS100
Bond Low Profile Lavatory Faucet (Less Handles)
• STYLE No. BLH02E
Bond Union Series Guilloche Pinstripe Lever Handle
STYLE No. BLS130
Bond Solo Series Lavatory Faucet with Knob Handles
• STYLE No. BLS100
Bond Low Profile Lavatory Faucet (Less Handles)
• STYLE No. BKH030
Bond Solo Series Knob Handle
STYLE No. BLS14A
Bond Tandem Series Lavatory Faucet with Guilloche Lines
Knob Handles
• STYLE No. BLS100
Bond Low Profile Lavatory Faucet (Less Handles)
• STYLE No. BKH04A
Bond Tandem Series Guilloche Lines Knob Handle
STYLE No. BLS14B
Bond Tandem Series Lavatory Faucet with Two-Tone Guilloche
Lines Knob Handles
• STYLE No. BLS100
Bond Low Profile Lavatory Faucet (Less Handles)
• STYLE No. BKH04B
Bond Tandem Series Two-Tone Guilloche Knob Handle
STYLE No. BLS14D
Bond Union Series Lavatory Faucet with Enamel Guilloche
Lines Knob Handles
• STYLE No. BLS100
Bond Low Profile Lavatory Faucet (Less Handles)
• STYLE No. BKH04A
Bond Tandem Series Guilloche Lines Knob Handle
• STYLE No. BKH00D
Bond Union Series Enamel Index
STYLE No. BLS15C
Bond Union Series Lavatory Faucet with Guilloche Link Knob
Handles
• STYLE No. BLS100
Bond Low Profile Lavatory Faucet (Less Handles)
• STYLE No. BKH05C
Bond Union Series Guilloche Link Knob Handle
PRODUCT SUPPORT | 800.927.2120 | WATERWORKS.COM PAGE 2 OF 6 | UPDATED ON 3.05.2020
STYLE No. BLS130, BLS14A, BLS14B, BLS14D,
BLS15C
Bond Low Profile Lavatory Faucet with Knob
Handles
STYLE No. BLS110, BLS12A, BLS12B, BLS12C,
BLS12D, BLS12E
Bond Low Profile Lavatory Faucet with Lever
Handles
INSTALLATION GUIDELINES
IMPORTANT:
To ensure this product is installed properly, you must read and follow
these guidelines.
The owner/user of this product must keep this information for future
reference.
This product must be installed by a professional licensed contractor.
Be sure your installation conforms to federal, state, and local codes.
In the State of Massachusetts, all installations must comply with the
rules and regulations set forth within 248 CMR.
Inspect this product to ensure you have all the parts required for
proper installation.
Product is sold partially assembled but shown fully disassembled for
illustrative and service purposes only.
CAUTION: Use only a strap wrench or protected/smooth-jaw wrench
on ANY finished surface.
CAUTION: This product is supplied with a DRAIN that is NOT
compatible with SINKS that have a 1-1/2” [38mm] drain hole. A 1-3/4”
drain hole is REQUIRED.
The use of certain plumber’s putty may stain stone or tile surfaces.
If further assistance is required, please contact Product Support at
1-800-927-2120 Monday through Friday, 8am – 6pm EST.
Refer to the separate Service Parts Documents for available
replacement parts.
TECHNICAL DETAILS:
DETAIL SPECIFICATION
DECK THICKNESS MAXIMUM 1-11/16” [43mm]
DECK THICKNESS MINIMUM 1/4” [6mm]
DRAIN DEPTH MAXIMUM 2-5/8” [67mm]
DRAIN DEPTH MINIMUM 3/8” [10mm]
DRAIN HOLE DIAMETER Ø1-3/4” [44mm]
DRAIN STYLE PUSH-TOUCH
FITTINGS HOLE DIAMETER Ø1-3/8” [35mm]
HANDLE SPREAD MAXIMUM 12” [305mm]
HAND SPREAD MINIMUM 8” [203mm]
HANDLE TURN ANGLE QUARTER TURN
INLET CONNECTION 1/2” MALE WITH SUPPLY NUT
SPOUT REACH 5-5/8” [143mm]
WATER PRESSURE MAXIMUM 85psi [6.0 bar]
WATER PRESSURE MINIMUM 20psi [1.5 bar]
WATER PRESSURE RECOMMENDED 45psi [3.0 bar]
PRODUCT SUPPORT | 800.927.2120 | WATERWORKS.COM PAGE 3 OF 6 | UPDATED ON 3.05.2020
STYLE No. BLS130, BLS14A, BLS14B, BLS14D,
BLS15C
Bond Low Profile Lavatory Faucet with Knob
Handles
STYLE No. BLS110, BLS12A, BLS12B, BLS12C,
BLS12D, BLS12E
Bond Low Profile Lavatory Faucet with Lever
Handles
1. Remove the TEE, NUT and LOWER DECK
WASHERS from the SPOUT SHANK.
NOTE: Do NOT remove the FOAM GASKET beneath
the ESCUTCHEON or discard the FIBER WASHER
provided with the TEE.
2. Insert the SHANK through the hole on the
mounting surface, making sure the FOAM GASKET
is beneath the ESCUTCHEON, then re-install the
LOWER DECK WASHERS and securely tighten the
NUT.
3. Thread and securely tighten the TEE onto the
SHANK making sure to use the FIBER WASHER
provided.
INSTALLATION GUIDELINES
SIDEBODY
RUBBER &
METAL
WASHERS,
SPACER,
NUT
FOAM
WASHER
TRIM
CONNECTOR
NUT
SIDEBODY
MOUNTING
SURFACE
FOAM WASHER
TRIM CONNECTOR
6. Ensure the SIDEBODY is positioned so the SUPPLY
HOSE can be easily connected to the TEE then
thread and securely tighten the NUT against the
underside of the mounting surface.
NOTE: Repeat steps 4 - 6 to insall the 2ND
SIDEBODY.
4. Unthread and remove the TRIM CONNECTOR and
FOAM WASHER from the SIDEBODY then fully
thread the NUT down the SIDEBODY.
NOTE: Do NOT remove the LOWER DECK
WASHERS and SPACER.
5. Using the FOAM WASHER provided, thread the
TRIM CONNECTOR back onto the SIDEBODY until
it stops then let it rest on the mounting surface.
FOAM
GASKET
[DO NOT
REMOVE]
ESCUTCHEON
SPOUT SHANK
RUBBER WASHER
METAL WASHER
NUT
TEE
FIBER WASHER
NUT
METAL WASHER
RUBBER WASHER
FOAM GASKET
ESCUTCHEON †
MOUNTING
SURFACE
SPOUT
† A GASKET for the ESCUTCHEON
is provided. If desired, a bead of
caulk or a clear silicone may be
applied where the ESCUTCHEON
contacts the mounting surface.
TEE
SHANK
FIBER
WASHER
MOUNTING
SURFACE
[UNDERSIDE]
RUBBER WASHER,
SPACER,
METAL WASHER
NUT
[SECURELY
TIGHTEN]
PRODUCT SUPPORT | 800.927.2120 | WATERWORKS.COM PAGE 4 OF 6 | UPDATED ON 3.05.2020
STYLE No. BLS130, BLS14A, BLS14B, BLS14D,
BLS15C
Bond Low Profile Lavatory Faucet with Knob
Handles
STYLE No. BLS110, BLS12A, BLS12B, BLS12C,
BLS12D, BLS12E
Bond Low Profile Lavatory Faucet with Lever
Handles
INSTALLATION GUIDELINES
9. CAREFULLY slide the ESCUTCHEON up the LEVER
HANDLE to expose the UNION NUT then thread
the NUT into the TRIM CONNECTOR until it stops.
10. CAREFULLY slide the ESCUTCHEON down the
LEVER HANDLE to conceal the TRIM CONNECTOR.
NOTE: Repeat steps 9 - 10 to install 2ND HANDLE.
8. Fully thread the ESCUTCHEON into the TRIM
CONNECTOR, place the KNOB onto the HANDLE
STEM, thread and securely tighten the SCREW, and
re-attach the INDICE.
NOTE: Repeat steps 7 - 8 to install 2ND HANDLE.
7. Remove the INDICE, center SCREW and KNOB
HANDLE from the ESCUTCHEON. Do NOT remove
the internal SPRING.
NOTE: To remove the INDICE push down on and
rotate it 45° then release.
STEPS 7 - 8
FOR
KNOB HANDLE
ONLY
STEPS 9 - 10
FOR
LEVER HANDLE
ONLY
PROCEED TO
STEP 11
PROCEED TO
STEP 11
ESCUTCHEON
KNOB HANDLE
[INTERNAL SPRING
MECHANISM]
SCREW
[2.5mm
HEX]
INDICE
[45°]
TRIM
CONNECTOR
HANDLE
STEM
ESCUTCHEON
KNOB
HANDLE
SCREW
[2.5mm HEX] INDICE
ESCUTCHEON
LEVER
HANDLE
NOTCH
[TOWARDS
BACKSPLASH/
WALL]
TRIM
CONNECTOR
UNION
NUT
LEVER
HANDLE
ESCUTCHEON
[INTERNAL
O-RING]
PRODUCT SUPPORT | 800.927.2120 | WATERWORKS.COM PAGE 5 OF 6 | UPDATED ON 3.05.2020
STYLE No. BLS130, BLS14A, BLS14B, BLS14D,
BLS15C
Bond Low Profile Lavatory Faucet with Knob
Handles
STYLE No. BLS110, BLS12A, BLS12B, BLS12C,
BLS12D, BLS12E
Bond Low Profile Lavatory Faucet with Lever
Handles
15. Using the LOWER DRAIN GASKET and SCREW
provided, re-attach the LOWER DRAIN BODY to
the FLANGE. Ensure the GASKET makes a full seal
on the underside of the LAVATORY then securely
tighten the SCREW.
16. Re-install the DRAIN STOPPER and TAILPIECE
using the WASHER and NUT provided.
INSTALLATION GUIDELINES
TAILPIECE
NUT
TAILPIECE
RUBBER
WASHER
LOWER DRAIN
BODY
DRAIN
STOPPER
LOWER DRAIN
BODY
LOWER DRAIN
GASKET *
DRAIN
FLANGE *
SCREW
[5/32" OR
4mm HEX
KEY]
* PUTTY OR A CLEAR
ADHESIVE MAY BE
USED TO ENSURE A
WATERTIGHT SEAL
BETWEEN THE
GASKET AND
LAVATORY
14. Set the DRAIN FLANGE into the LAVATORY (sold
separately) using putty or a clear adhesive silicone.
13. Unthread and remove the DRAIN STOPPER and
LOWER DRAIN BODY from the DRAIN FLANGE.
NOTE: Do NOT remove or discard the LOWER
DRAIN GASKET.
12. Unthread and remove the NUT, TAILPIECE, and
RUBBER WASHER from the LOWER DRAIN BODY.
LOWER DRAIN
GASKET
[DO NOT REMOVE]
LOWER DRAIN
BODY
UPPER DRAIN
GASKET
[CAN BE
DISCARDED]
DRAIN FLANGE
SCREW
[5/32" OR
4mm HEX KEY]
DRAIN
STOPPER
11. Connect the SIDEBODIES to the TEE using the
SUPPLY HOSES provided. Securely tighten the
HOSES and ensure they are not pinched/kinked.
LAVATORY
DRAIN
FLANGE *
* USE PUTTY OR A CLEAR ADHESIVE SILICONE
TAILPIECE NUT
TAILPIECE
RUBBER WASHER
LOWER DRAIN BODY
SUPPLY
HOSE
TEE
SUPPLY
HOSE
[2ND]
PRODUCT SUPPORT | 800.927.2120 | WATERWORKS.COM PAGE 6 OF 6 | UPDATED ON 3.05.2020
STYLE No. BLS130, BLS14A, BLS14B, BLS14D,
BLS15C
Bond Low Profile Lavatory Faucet with Knob
Handles
STYLE No. BLS110, BLS12A, BLS12B, BLS12C,
BLS12D, BLS12E
Bond Low Profile Lavatory Faucet with Lever
Handles
17. Make final P-TRAP (sold separately) and SUPPLY
VALVE (sold separately) connections.
18. Remove the AERATOR, turn on the water supply
and open the HANDLES to flush out the supply
lines, and inspect all connections for leaks then
close the DRAIN to ensure it functions properly.
19. Close the HANDLES, open the DRAIN to drain the
water, and re-install the AERATOR.
INSTALLATION GUIDELINES
1. REMOVE AERATOR
3. CLOSE
DRAIN
AERATOR
AERATOR
KEY
2. TURN ON WATER SUPPLY
AND OPEN HANDLES
2. OPEN
DRAIN
AERATOR
AERATOR
KEY
1. CLOSE HANDLES 3. INSTALL AERATOR
P-TRAP
[NOT
SUPPLIED]
TAILPIECE
SUPPLY VALVE
[NOT SUPPLIED]
SUPPLY TUBE
[NOT SUPPLIED]
SUPPLY NUT
[SUPPLIED]
SIDEBODY
[1/2" INLET]
-
1
-
2
-
3
-
4
-
5
-
6
WaterWorks BLS12D Installation guide
- Category
- Sanitary ware
- Type
- Installation guide
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
WaterWorks RRLS11 Installation guide
-
-
-
-
-
-
-
-
-
Other documents
-
Schlage ND Operating instructions
-
Moen 5901P Owner's manual
-
-
-
American Standard 7415.821 User manual
-
American Standard 7415.821.224 Installation guide
-
-
-
Kohler 7307-KE-CP Installation guide
-