WaterWorks DSLS20 Installation guide

WaterWorks
Brand
WaterWorks
Model
DSLS20
Type
Installation guide

This manual is also suitable for

STYLE No. DSLS20
Dash Gooseneck Three Hole
Deck Mounted Lavatory Faucet
with Metal Cross Handles
STYLE No. DSLS01
Dash Low Profile Three Hole
Deck Mounted Lavatory Faucet
with Metal Cross Handles
INSTALLATION GUIDELINES
PAGE 1 OF 4 | UPDATED ON 2.21.2023
PRODUCT SUPPORT | 800.927.2120 | WATERWORKS.COM
IMPORTANT:
To ensure this product is installed properly, you must read and
follow these guidelines.
The owner/user of this product must keep this information for
future reference.
This product must be installed by a professional licensed
contractor.
Be sure your installation conforms to federal state, and local
codes. In the State of Massachusetts, all installations must
comply with the rules and regulations set forth within 248 CMR.
Inspect this product to ensure you have all the parts required
for proper installation. Product is sold partially assembled but
shown fully disassembled for illustrative and service purposed
only.
Use only a strap wrench or protected/smooth-jaw wrench on
any finished surface.
The use of certain plumber’s putty may stain stone or tile
surfaces.
If further assistance is required, please contact Product Support
at 1-800-927-2120 Monday through Friday, 8am – 6pm EST.
Refer to the separate Service Parts Documents for available
replacement parts.
TECHNICAL DETAILS:
STYLE DETAIL SPECIFICATION
ALL DECK THICKNESS 1/4” [6mm] MIN
1-9/16” [40mm] MAX
ALL DRAIN DEPTH 3/8” [10mm] MIN
2-5/8” [67mm] MAX
ALL DRAIN HOLE DIAMETER Ø1-3/4” [44mm]
ALL DRAIN STYLE PUSH TOUCH
ALL FITTINGS HOLE DIAMETER Ø1-3/8” [35mm]
ALL HANDLE SPREAD 8" [203mm] MIN
12” [305mm] MAX
ALL HANDLE TURN ANGLE QUARTER TURN
ALL INLET CONNECTION 1/2" Male with
Supply Nut
DSLS01
SPOUT REACH
5-3/4” [145mm]
DSLS20 6-1/16” [154mm]
ALL CARTRIDGE VALVE MATERIAL CERAMIC
ALL WATER PRESSURE RANGE 20psi [1.5 bar] MIN
85psi [6.0 bar] MAX
ALL WATER PRESSURE RECOMMENDED 45psi [3.0 bar]
STYLE No. DSLS20
Dash Gooseneck Three Hole
Deck Mounted Lavatory Faucet
with Metal Cross Handles
STYLE No. DSLS01
Dash Low Profile Three Hole
Deck Mounted Lavatory Faucet
with Metal Cross Handles
INSTALLATION GUIDELINES
PAGE 2 OF 4 | UPDATED ON 2.21.2023
PRODUCT SUPPORT | 800.927.2120 | WATERWORKS.COM
SPOUT ESCUTCHEON
[DO NOT REMOVE]
RUBBER WASHER
[DO NOT REMOVE]
SHANK
RUBBER
WASHER
METAL
WASHER NUT
RUBBER WASHER
TEE
TEE
RUBBER WASHER
NUT
METAL WASHER
RUBBER WASHER
MOUNTING
SURFACE
SHANK
RUBBER WASHER*
ESCUTCHEON
SPOUT
* If desired, a bead of
caulk or a clear
silicone may be
applied where the
ESCUTCHEON
contacts the
mounting surface.
SIDEBODY
GLAND COVER
HANDLE
FINISHED SCREW
[CAUTION]
1. Remove the TEE, NUT and lower deck WASHERS
from the SPOUT SHANK. Do NOT remove the
WASHER from the ESCUTHCEON.
2. Insert the SHANK through the hole on the
mounting surface then re-attach the WASHERS,
NUT, and TEE and securely tighten the NUT.
3. Carefully unthread the FINISHED SCREW then pull
the HANDLE and GLAND COVER up.
PLASTIC
BUSHING
[DO NOT
REMOVE]
PLASTIC SPACER,
RUBBER WASHER,
METAL WASHER,
NUT
SIDEBODY
TRIM CONNECTOR
O-RING
ESCTUCHEON
TRIM NUT
[16mm WRENCH]
4. Unthread and remove the TRIM NUT, remove the
ESCUTCHEON with the O-RING, unthread and
remove the TRIM CONNECTOR then fully thread
the NUT down the SIDEBODY.
CAUTION: Do NOT remove the PLASTIC BUSHING
on the TRIM NUT
PLASTIC SPACER,
RUBBER WASHER,
METAL WASHER,
NUT
SIDEBODY
TRIM CONNECTOR
5. Thread the TRIM CONNECTOR back onto the
SIDEBODY until it stops and let is rest on the
mounting surface then hand-tighten the NUT
against the underside of the mounting surface.
CAUTION: Do NOT over tighten the NUT to allow
for proper handle alignment during HANDLE
installation.
SIDEBODY
MOUNTING
SURFACE
TRIM
CONNECTOR
O-RING*
ESCTUCHEON
TRIM NUT
[16mm WRENCH]
* If desired, a bead of
caulk or a clear
silicone may be
applied where the
ESCUTCHEON
contacts the
mounting surface.
6. Place the ESCUTCHEON and O-RING over the TRIM
CONNECTOR then thread and securely tighten the
TRIM NUT into the TRIM CONNECTOR;
STYLE No. DSLS20
Dash Gooseneck Three Hole
Deck Mounted Lavatory Faucet
with Metal Cross Handles
STYLE No. DSLS01
Dash Low Profile Three Hole
Deck Mounted Lavatory Faucet
with Metal Cross Handles
INSTALLATION GUIDELINES
PAGE 3 OF 4 | UPDATED ON 2.21.2023
PRODUCT SUPPORT | 800.927.2120 | WATERWORKS.COM
NUTSIDEBODY
TRIM NUT
GLAND COVER
HANDLE
FINISHED SCREW
SIDEBODY
[2ND]
HANDLE
[2ND]
SCREW
SIDEBODY
[2ND]
SUPPLY HOSE*
[2ND]
TEE
SUPPLY HOSE*
SIDEBODY
* WARNING:
ENSURE THE HOSES ARE NOT
PINCHED/KINKED
7. Re-attach the GLAND COVER, HANDLE, and
FINISHED SCREW. Ensure the HANDLE is in the
desired orientation then securely tighten the NUT
on the SIDEBODY.
8. Repeat Steps 3 through 7 to install the second
HANDLE.
9. Connect the SIDEBODIES to the TEE using the
SUPPLY HOSES provided. Securely tighten the
HOSES and ensure they are not pinched/kinked.
TAILPIECE NUT
TAILPIECE
RUBBER
WASHER
LOWER DRAIN
BODY
10. Remove the TAILPIECE from the LOWER DRAIN
BODY.
LOWER DRAIN
GASKET
[DO NOT REMOVE]
LOWER DRAIN
BODY
UPPER DRAIN
GASKET
DRAIN FLANGE
SCREW
DRAIN STOPPER
[CAN BE DISCARDED]
[5/32" OR
4mm HEX
KEY]
11. Unthread and remove the DRAIN STOPPER and
LOWER DRAIN BODY from the DRAIN FLANGE
The UPPER DRAIN GASKET can be discarded.
CAUTION: Do NOT discard the LOWER DRAIN
GASKET.
LAVATORY
DRAIN
FLANGE*
* USE PUTTY OR A
CLEAR ADHESIVE
SILICONE
12. Set the DRAIN FLANGE in the lavatory [SOLD
SEPARATELY] using putty or a clear adhesive
silicone.
STYLE No. DSLS20
Dash Gooseneck Three Hole
Deck Mounted Lavatory Faucet
with Metal Cross Handles
STYLE No. DSLS01
Dash Low Profile Three Hole
Deck Mounted Lavatory Faucet
with Metal Cross Handles
INSTALLATION GUIDELINES
PAGE 4 OF 4 | UPDATED ON 2.21.2023
PRODUCT SUPPORT | 800.927.2120 | WATERWORKS.COM
LOWER DRAIN
BODY
LOWER DRAIN
GASKET*
DRAIN
FLANGE*
SCREW
[5/32" OR
4mm HEX
KEY]
* PUTTY OR A CLEAR
ADHESIVE MAY BE
USED TO ENSURE A
WATER-TIGHTE SEAL
BETWEEN THE
GASKET AND
LAVATORY
TAILPIECE NUT
LOWER DRAIN
BODY
TAILPIECE
RUBBER
WASHER
DRAIN
STOPPER
SUPPLY VALVE
[NOT SUPPLIED]
P-TRAP
[NOT
SUPPLIED]
TAILPIECE
SUPPLY TUBE
[NOT SUPPLIED]
SUPPLY NUT
[SUPPLIED]
13. Re-install the LOWER DRAIN BODY making sure to
use the GASKET provided. Ensure the GASKET
makes a full seal on the underside of the lavatory
then securely tighten the SCREW.
14. Re-install the DRAIN STOPPER then the TAILPIECE
using the WASHER and NUT provided.
15. Make final P-TRAP [sold separately] and SUPPLY
VALVE [sold separately] connections.
AERATOR
TOOL
AERATOR
1. REMOVE AERATOR
3. CLOSE DRAIN
2. TURN ON WATER AND
OPERATE HANDLES
16. Removed the AERATOR, turn on the water to flush
out the supply lines, and inspect all connections for
leaks. Close the DRAIN.to ensure it functions
properly then turn off the water and re-install the
AERATOR.
NOTE: 2-3 Seconds of residual water is typical on
large gooseneck faucets.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

WaterWorks DSLS20 Installation guide

WaterWorks
Brand
WaterWorks
Model
DSLS20
Type
Installation guide
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents