GE ZDBI240WBII Installation guide

Design Guide with

Installation

Instructions

Wine Chiller, Wine Reserve

and Beverage Center

monogram.corn

Safety Information

BEFORE YOU BEGIN:

Read these instructions completely and carefully.

IMPORTANT - Savetheseinstructions

for local inspector's use.

IMPORTANT- Observe all governing codes

and ordinances.

Note to Installer - Be sure to leave these

instructions with the Consumer.

Note to Consumer - Keepthese instructions with

your Owner's Manual for future reference.

WARNING - Thisappliance mustbeproperly

grounded. See page 4,

AVERTISSEMENT -

Cet oppareil doit _tre correctement mis (_la terre.

Consultez page 4.

If you received a damaged wine chiller, wine reserve

or beverage center, you should immediately contact your

dealer or builder.

Skill Level -Installation requires basic mechanical

skills. Proper installation is the responsibility of the

installer. Product failure due to improper installation

is not covered under the GE Appliance Warranty.

WARNINGS:

• Use this appliance only for its intended purpose.

• Immediately repair or replace electrical service cords

that become frayed or damaged.

• Unplug the unit before cleaning or making repairs.

• Repairs should be made by o qualified service

technician.

AVERTISSEMENT:

• II ne faut utiliser cet appareil que pour l'usoge pour

lequel il o _t_ construit.

• IIfout r_porer ou remplocer imm_diotement tout

cordon d'ulimentation _lectrique effiloch_ ou

endommog&

• D_bruncher le bar ou le r_frig_ruteur o vin ovont

le nettoyage ou toute intervention.

• Les r_porotions doivent _tre fakes par un technicien

quolifi&

For Monogram local service in gour area, call

1.800.444.1845

For Monogram service in Canada, call

1.800.561.3344

For Monogram Parts and Accessories, call

1.800.626.2002.

www.monogram.com

CONTENTS

Design Guide

The Installation Space .............................3

Product Clearances ...................................3

Side-by-Side Installation ........................3

Installation Instructions

Tools, Hardware ..........................................4

Grounding the Product ............................4

Staining Wood Drawer Fronts ..............4

Installing the Custom Frame Panel ...4

Step 1 Remove Packaging ....................4

Step 2, Reverse Door Swing ..................5

Step 3, Leveling ...........................................6

Step 4, Connect Power ............................6

Step 5, Slide Product into Cutout ........6

Step 6, Install Nameplate .......................6

Step 7, SetTemperature Controls ......6

Custom Frame Panel Models ...............6

ZTBSS1Honogram

Tubular Handle Kit.....................................7

Template for Nameplate _ Back Cover

Design Guide

THE INSTALLATION SPACE

34-1/2"-35"

Min.

NOTE:

Handle

and handle

standoff depth

is 1-3/4"

24-1/8" Framed Models

23-3/4"StainlessSteelModels

1_23-3/4"_

The cutout depth should be 24"

The cutout dimensions shown allow for a full door swing

and access to the pull-out racks when installed as a

built-in in standard 24" deep cabinets.

• The wine chiller, wine reserve and beverage center

can be installed freestanding.

• If installing between frameless cabinets, a 1/2" wide

filler strip or side panel mag be needed on hinge side.

The filler strip will act as a spacer between the case

and adjacent cabinet door swing. The width

of the opening must include the filler panels.

NOTE:The door should protrude 1" begond the

surrounding cabinets. Custom framed models will

protrude 1-7/8" begond surrounding cabinet doors.

Additional Specifications

• A 120 volt 60Hz., 15 or 20 amp power supplg is

required. An individual properlg grounded branch

circuit or circuit breaker is recommended. Install a

properlg grounded 3-prong electrical receptacle

recessed into the back wall as shown. Electrical must

be located on rear wall as shown. NOTE:GFI(ground

fault interrupter) is not recommended.

PRODUCT CLEARANCES

Thestainlesssteelwine chiller,wine reserveand beverage

center isfactorg setfor a 110°door swing.Modelsthat accept

custom panelshavea 95°door swing.

Wheninstalled in a corner:

• Allow4" min.clearanceonthe hingesidefor the 90°door

swingand to allowracksto slideout.

• Allow 10"minimumclearanceon the hingesidefor afull

110°door swing.(ModelsZDWI240WIIand ZDBI240WIIhave

a 95°doorswing.)

NOTE:Customhandleclearancesmagvarg, dependingon

custom handle depth.

10"Minimum

toWall

I 1

i i

10o* ,,

1 ... \_

"95° Door Swing on Custom Frame Models

90° DoorSwing

[ ,

21-5/8"

L- i

1 ;

;

1 23-5/8"

90° i

4"Minimum

to Wall

• Thedoorswingisreversibleonallmodels.Ifdesired,changethe

doorswingbeforeinstallationorbeforeinstallingthecustomflame

panel.

Choosethelocation:

• Theseproductsmagbeclosedinonthetopandthreesidesaslong

asthefrontisunobstructedforaircirculationandproperaccessto

thedooE

• Donotinstalltheseproductswherethetemperaturewillgobelow

S5°F(13°C)orabove90°F(32°C).

• Donotinstallwhereitwillbesubjecttodirectsunlight,heator

moisture.

• Theseproductsarenotdesignedto bestackedoneovertheotheE

Blackor StainlessSteelToekickOptions

• Theseproductsareshippedwitha blacktoekickinstalled.

Anoptionalstainlesssteeltoekickisalsosuppliedwitheach

product.Forshippingpurposes,thestainlesssteeltoekickis

securedtothebackoftheunit.

ZTBSS1TubularHandle

ZTBSS1Monogramstainlesssteeltubularhandleisavailablefor

modelsZDWI240WIIandZDBI240WII.

SIDE-BY-SIDE INSTALLATIONS

Increase storage capacitg bg installing two Monogram

beverage centers, wine chillers or wine reserves together

Or,for a complete refreshment center, install ang two

of these units together.

• A side-bg-side installation requires at least a 47-1/2"

wide opening. No trim kits required.

• Products must operate from separate, properlg

grounded receptacles.

34-1/2"-35"

Installation Instructions

TOOLS REQUIRED

• #2 Phillips screwdriver

• Adjustable wrench

PARTS SUPPLIED

• Monogram nameplate

• Hardware for changing door swing

• Optional stainless steel toekick with screws and

spacers

• Left and right side hinge covers

• Top screw hole cover

GROUNDING THE WINE CHILLER,

WINE RESERVE AND BEVERAGE

CENTER

IMPORTANT - Pleasereadcarefullg.

FOR PERSONAL SAFETY',THIS APPLIANCE MUST BE

PROPERLY'GROUNDED.

The power cord of this appliance isequipped with o

three-prong (grounding) plug which mates with a

standard three-prong (grounding) wall receptacle to

minimize the possibility of electric shock hazard from

this appliance.

Have the wall outlet and circuit checked by a qualified

electricianto makesurethe outlet ispropedggrounded.

Where a standard 2-prong wall outlet is encountered, it

is gour personal responsibilitg and obligation to have it

replaced with a properlg grounded B-prong wall outlet.

DO NOT, UNDER ANY

CIRCUMSTANCES, CUT

OR REMOVE THE THIRD

(GROUND) PRONG

FROM THE POWER CORD.

DO NOT USEAN ADAPTER PLUG TO CONNECTTHE

REFRIGERATORTO A 2-PRONG OUTLET.

DO NOT USEAN EXTENSION CORD WITH THIS

APPLIANCE.

STAINING WOOD DRAWER FRONTS

The drawer fronts are unfinished cherrg wood. During

use, oil from hands may accumulate and stain the

wood.

• The drawer fronts may be stained and sealed to

match adjacent cabinetrg. The tinted glass will make

the stained wood appear darkeE A true color match

can be seen onlg when the door is opened.

• Applg the stain and sealer according to the

manufacturer's instructions. To avoid unpleasant

odor, keep the door open to ventilate and allow

the stain/sealer to drg completelg before using

the product.

INSTALLING THE CUSTOM FRAME PANEL

Go to page 6 for custom frame panel size,depending

on gour cabinet size and style.

• Install a custom handle of gour choice or optional

ZTBSS1Tubular Handle onto the custom panel before

the panel is secured to the door.

• The custom panel should be installed before sliding

the product into the installation location.

ISTEP1] REMOVE PACKAGING

•Remove cornerblocksand foam drawerstops.

•Remove allpackingmaterial,topeand protective

plasticcoverings.

•Remove stainlesssteeltoekicktapedtotheback

oftheunit.

CAUTION: Small objects area choke hazard

for children. Remove and discord ong parts not used.

MISE EN GARDE :Lespetitsobjets

peuvent @tronglerles enfonts. IIfoutjeter toutes les

pi@cesqui ne sont pos utilis@es.

Installation Instructions

ISTEP 2 IREVERSE DOOR SWING

SKIPTHIS STEPIF DOORSWING SUITSTHE

INSTALLATION

Parts Included:

• Top left case hinge

• Bottom left case hinge

• Left and right side decorative hinge cover

• Decorative hinge screw hole cover

• Torx ® driver bit

Tools Required:

• Phillips screwdriver

• Electric drill

Remove the door:

• Flatten the shipping carton to use as a pad.

• Remove the 2 screws and the toekick. Set aside the

screws and toekick for final installation.

• Use the supplied Torx® bit and electric drill to remove

the 3 screws holding the top case hinge. Lift off the

hinge.(Screwswill be used to install the new hinge.)

• Lift the door off the bottom case hinge.

• Remove the bottom case hinge pin and bracket.

Rotate the door:

The handle will be on the right side of the door; hinges

will be installed on the left side of the case.

• Remove the door stop and cam riser on the original

bottom right side of the door.

• Remove the fill plug on the top right side

of the door.

• Turn the door over and reinstall the fill plug on the

new left side.

Reinstall the door:

• Install the original door stop and cam riser onto the

bottom left side of the dooE

• Install the new supplied bottom case hinge pin and

bracket onto bottom left side.

• Placethe door onto the bottom case hinge.

• Install the supplied left-hand top case hinge with the

3 original screws.

• Select the hinge cover marked with an "L".

• Peel backing off the tape inside the decorative hinge

coveE InstallCovers

• Pressand snap the hinge _

cover into place. &..

• Snap the screw hole cover into _I/

place on the opposite side.

IMPORTANT:

Check to be sure screws are tight and that the door

is straight and does not sag. The door should swing

freelu.

Install

3 Hinge i _

Screws i

Remove

Top Hinge

Remove

Hinge

Pinand

Bracket

Apply Monogram Nameplate:

• Install the Monogram nameplate. See instructions

and template on back cover,

Install Toekick

The toekick has a

cutout on the left

and right sides. 1 II _I

Remove /f_J_l _----- ] II

the plug on |

the left side L MoveFill

and ( I ', _] Plugto

reinstall on \ I,,,,,_', /_t RightSide

the right X _ _ /

side. If Uou

choose to _L __ "'_

install the -_

stainless steel toekick,

reinstall the plug on the right side of that toekick.

• Install original screws and spacers or screws and

spacers supplied with the stainless steel toekick.

Install screws through the spacer standoff, toekick

and into the base as shown.

Installation Instructions

ISTEP 31LEVEL

• Use an adjustable wrench to turn the leveling legs and

raise or lower the product.

• Adjust carefullg; the product should be level and plumb

with cabinetry, and should align with adjacent toekick

height.

TurnRightto Lower

TurnLeftto Raise

If gou skipped Step 2:

• Selectthe hinge cover marked "R"or "L",depending

on door swing.

• Peel backing off the tape inside the decorative

hinge cover. Pressand snap into position.

• Snap the screw hole cover into place on the

opposite side.

ISTEP 41CONNECT POWER

• Connect power cord plug to a properlg grounded

receptacle.

• Check to make sure power is on by opening the door

to see if interior light turns on.

ISTEP SI SLIDE PRODUCT INTO

THE CUTOUT

• Carefully, slide the unit into the opening. Be careful

not to entangle the power cord.

• Make certain that the door protrudes 1" beyond

the surrounding cabinets (1-7/8" for custom frame

models).

• Check again to be sure the unit is level.

[STEP 6] INSTALL NAMEPLATE

• Follow instructions on the back page for installation of

the Monogram nameplate.

[STEP 7] SET TEMPERATURE CONTROLS

• Thetemperature controls are preset. Refer to the

Owner's Manual for more information. Allow 24 hours

for temperature to stabilize.

CUSTOM FRAME PANEL MODELS

ModelZDWI240WIIand ZDBI240WlI

Thesemodelsrequirea custom panelframesurrounding

the glass.Thereare two options:the panel mug be 29-3/4"

or 30" high.A 30"panelrequiresa notch cut into the bottom

of the panelto avoid interferencewith the hinges.

• Routthe backsideofthe panelto the dimensionsshown.

• A custom handle of yourchoice or ZTBSS1TubularHandle

must be installedbeforethe panelis mounted onto

the door.

NOTE:The 4 corners

of the routed areas

mustbe squared J

to fit the coroers/

ofthe metal / - , I\

door frame.

Option 1 Option 2

I-- 23-1/8"--

2-1/4"

wide, _

°ffhel ! ] I deep,1-1/8"wide I

°, i I

- /8 w de : / 2-1/2 at--I :3

[_ _ bottom t --

3/4" Thick Custom Pane I--I

Sack Side 2-1/4"

NOTE: Right-hand models Cutthe notch

illustrated. Cut notches I/8" deep,1/4"

for hinge clearance onthe wide and1/4"

opposite side for left-hand high

door swing.

ChooseOption1 or Option2 panelsizedependingon

cabinetry sizeor stgle.

NOTE:A solid panel that covers the door glass CANNOTbe

installed on these models.

Installthe custom panel:

• Openthedoor fully.

• Removethe gasketsurroundingthe insideofthe doorto

exposethe existingscrewholesfor the custompanel.

• Holdthecustom frame panelagainstthe door andalign

carefullg,topto bottomand sideto side.Harkscrewhole

locationsonthe backsideofthe panel.

• Drillpilot holesinthe back sideofthe custom panel.In

hardwood,drill 3/32" pilot holes.Insoftwood,drill 5/64" holes.

• Securethe preparedpaneltothe door usingten (10)

#8 x 5/8" screws.Drivethescrewsthroughthe doorframe

and intothe wood.

• Replacethe gasket.

#8x5/8"

m m Screws

GLASS

Back

÷ ÷

fDoor

Frame

/./Custom

Framed

Panel

ZTBSS1 Monogram Tubular Handle Kit

BEFOREYOU BEGIN:

Read these instructions completely and carefully.

IMPORTANT - Savetheseinstructions

for Iocul inspector's use.

IMPORTANT- Observe oil governing codes

and ordinances.

Note to Installer - Be sure to leave these

instructions with the Consumer.

Note to Consumer- Keepthese instructions

with your Owner's Manual for future reference. This kit

provides o stainless steel tubular handle to coordinate

with other Monogram appliances.

• The tubular handle must be installed onto the 3/4" thick

portion of the custom wood panel before the panel is

secured to the doo_

TOOLS AND MATERIALS REQUIRED

• Gloves to protect against sharp edges

• #2 Phillips screwdriver

• Drill and 1/4" bit and 1/2" spade bit

• Safety glosses

• Center punch

• Pencil

THIS KIT INCLUDES

• Tubular handle

• 2 Mounting screws

• 2 Handle standoffs

• 2 Set screws for standoffs

• 2 Nuts

• 2 Washers

• Allen Wrench

INSTALL THE TUBULAR HANDLE

• Use the handle as o template to locate and mark the

exact position of the screw holes. Be careful to ovoid

interference with custom panel mounting screws.

• Draw o pencil line, top to bottom and 7/8" from the

outside edge.

• Hold the tubular handle against the appearance side,

centered on the marked line.

• Mark the screw hole locations at the center of the

handle attachment posts.

• Center punch the marked hole locations. Drill 1/4"

pilot holes from the appearance side through the

entire panel thickness.

• Use o 1/2" spade bit to drill 1/4" to 5/16" deep into

the back side of the panel. Insert washer (spacer)into

the hole.

• Install screw through the handle standoff and into the

pilot hole.

• Fasten nut onto the screw until the standoff is tight

against the panel. The screw hole on the standoff

should be pointing down toward the floor.

• Place handle attachment posts inside the standoffs.

• Use the Allen wrench to install the set screws. Tighten

handle to standoffs.

24-7/32"

1_7/8"

::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::

Custom

,Framed

Panel --

Handle

Standoff

Screw

30"

JTubular

Handle

Attachment

Post

Set

Screw

TEMPLATE FOR NAMEPLATE LOCATION

Upper Left

Cornerof

Glassif Hinge

ison Left

_,j__ C_uton DottedLine

_Top of GlassDoor

TopofBadge_y

UpperRight

Cornerof

Glassif Hiflge

ison Right

:4 DoorFrameSide

Monogram.

DOORNAMEPLATELOCATION

DoorFrameSide

To position nameplate:

• Cut template along dotted line.

• Hold or tape template behind glass

door so that it isvisible from the

front side.

• Remove backing from nameplate.

• Place nameplate onto front side of

door, matching illustration on the

template.

IMPORTANT:Nameplate must

be placed on the opposite side of the

door handle.

Note: While performing installations described in this book,

safety glasses or goggles should be worn.

For i'4onogram ®local service in your area, call

1.800.444.1845.

Note: Product improvement is a continuing endeavor at

General Electric. Therefore, materials, appearance and

specifications are subject to change without notice.

Pub.No. 31-46122-2

Port No. 197D7840PO01

12-07 JR

Printed in Slovenia

GE Consumer & Industrial

Appliances

General Electric CompQn U

Louisville, KY 40225

ge.com

GE ZDBI240WBII, ZDBI240WIIA, ZDBR240PBBS, ZDWI240WBII, ZDWI240WIIA, ZDWR240PCBS Installation guide

Related papers

Other documents