Radiant Communications VL4500 SRT Encoder User manual

Category
Noise Reduction Machine
Type
User manual
VL4500 ENCODER SERIES
Installation and Operations Manual
User Guide
Radiant
Communications
Corporation
V L 4 5 0 0 E N C O D E R S E R I E S
Installation and Operation Manual
Radiant Communications Corp. 2017
5001 Hadley Road
South Plainfield, NJ 07080
Phone 908.757.7444 • Fax 908.757.8666
www.rccfiber.com
Table of Contents
Product Summary 1
Application ...................................................................................... 1
Features .......................................................................................... 2
Front Panel ..................................................................................... 3
Rear Panel ...................................................................................... 4
Encoding Profiles ............................................................................ 7
Output Interfaces ............................................................................ 7
Energy Specifications...................................................................... 8
Installation 9
Communication 11
Network Management ................................................................... 11
Configuration 13
Video Settings ............................................................................... 15
Audio Settings ............................................................................... 25
TS Settings ................................................................................... 26
Network Settings ........................................................................... 29
System Setup ................................................................................ 41
Firmware Upgrade: 44
User Presets ................................................................................. 45
Encoder Default Settings .............................................................. 46
Front Panel Interface..................................................................... 47
Revisions 48
V L 4 5 0 0 U S E R M A N U A L R E V . 3 . 0 0 . 0 6 1
Radiant Communications Corporation 2017
1
Product Summary
Application
With compression efficiency and advanced pre-processing, the VL4500 Series delivers both HD and SD
content at a low bitrates and uncompromised quality. As a result, the VL4500 Series can be used to
deliver video services across all networks and fulfill multiple applications for various business models.
The VL4500 Series encoders provide cost-effective live streaming of PEG and in-house channels. With
SD/HD simulcast function, the VL4500 allows the broadcaster to stream both SD and HD content from
one source by utilizing the video scaling and conversion functions while utilizing low power
consumption and minimal heat output.
The SFP output interface allows the operator to use either existing duplex or single fiber or 1000B RJ45.
PEG STUDIO
VL4500
text
CATV HUB
SFP
FIBER
DOCSIS
1
V L 4 5 0 0 U S E R M A N U A L R E V . 3 . 0 0 . 0 6 1
Radiant Communications Corporation 2017
2
Features
Multi-Stream Encoding
Superior HD Quality at Low Bitrates
Out-of-Band Management
Advanced Video Pre-Processing
GigE TS Interface
MPEG2 SD/HD
H.264 AVC SD/HD
VBR and CBR Encoding
AC-3 Audio Encoding
EIA-708/608 Closed Caption Support
IP, ASI and QAM output Options
Video Scaling and Conversion
Low Power Consumption and Heat Dissipation
V L 4 5 0 0 U S E R M A N U A L R E V . 3 . 0 0 . 0 6 1
Radiant Communications Corporation 2017
3
Front Panel
LCD/KEYPAD LED
LED
Power Indicates that the unit is powered on.
Status Indicates the current status of the encoding process.
Alarm Indicates any hardware errors
LCD/Keypad
Up Moves the cursor up in all menus.
Down Moves the cursor down in all menus.
Left Moves back a menu or will move the cursor to the left one digit.
Right Selects a menu item or will move the cursor to the right one digit
Plus Increments a digit when entering values.
Minus Decrements a digit when entering values.
Enter Confirms a value or menu selection.
V L 4 5 0 0 U S E R M A N U A L R E V . 3 . 0 0 . 0 6 1
Radiant Communications Corporation 2017
4
Rear Panel
POWER
+ V
TS OUT
EARTH
TS
SDI IN
TS OUT
SDI IN
RS232
Serial Port
MGMT
MGMT
10/100/1000
VL4510Q
10/100/1000
QAM
QAM
POWER
1 2
GND +12 V
POWER
+ V
10/100/1000
EARTH
TS
SDI IN
SDI IN
RS232
Serial Port
SFP
MGMT
MGMT
VL4500/SDI
TS OUTPUT
ASI OUT
ASI OUT
LOCK
RX|TX
LINK
POWER
1 2
GND +12 V
POWER
+ V
TS OUT
EARTH
TS
SDI IN
TS OUT
SDI IN
RS232
Serial Port
MGMT
MGMT
10/ 100/ 1000
VL4510C
10/ 100/ 1000
ASI OUT
ASI OUT
CVBS IN
CVBS IN
1 2 3 4 5
AUDIO IN
POWER
1 2
GND +12 V
V L 4 5 0 0 U S E R M A N U A L R E V . 3 . 0 0 . 0 6 1
Radiant Communications Corporation 2017
5
POWER
+ V
TS OUT
EARTH
TS
8 x SD/SDI IN
SD/SDI IN
MGMT
MGMT
10/100/1000
VL4528
10/100/1000
QAM
QAM
RJ45
SFP
123
4
567
8
ASI IN
ASI OUT
ASI IN
ASI OUT
POWER
+ V
TS OUT
EARTH
TS
4 x SD/SDI IN
SD/SDI IN
MGMT
MGMT
10/100/1000
VL4521
10/100/1000
QAM
QAM
RJ45
SFP
1
567
8
ASI IN
ASI OUT
ASI IN
ASI OUT
HD/SDI IN
POWER
+ V
TS OUT
EARTH
TS
2 x SDI IN
SDI IN
MGMT
MGMT
10/100/1000
VL4522
10/100/1000
QAM
QAM
RJ45
SFP
12
ASI IN
ASI OUT
ASI IN
ASI OUT
HD/SDI IN
POWER
1 2
GND +12 V
POWER
1 2
GND +12 V
POWER
1 2
GND +12 V
V L 4 5 0 0 U S E R M A N U A L R E V . 3 . 0 0 . 0 6 1
Radiant Communications Corporation 2017
6
Input Rear Panel Connections:
SDI Input SDI input supporting SD-SDI (SMPTE-259M), HD-SDI (SMPTE-292M) and 3G-
SDI (SMPTE-424M), 75Ω BNC Connector
VL4500/SDI Inputs:
o SDI BNC input supporting SD-SDI (SMPTE-259M), HD-SDI (SMPTE-292M) and 3G-SDI
(SMPTE-424M), 75Ω BNC Connector, Signal Lock LED
o Fiber SDI input supporting up to 3G over fiber. SFP Module RX port is on the left side,
Optical Link LED
o SDI input switches with optical link status. When optical link is detected the active input
SDI port is the optical. If optical link is lost the input port switches to coax SDI input BNC port.
o CVBS Input, NTSC 1Vp-p, 75 Ohm.(VL4510C only)
o Analog Audio Input, 600 Ohm, balanced Input(VL4510C only)
1 2 3 4 5
Pin Function
1 Audio In 1 +
2 Audio In 1 -
3 GND
4 Audio In 2 +
5 Audio In 2 -
o Input Select Switch. Left Side SDI Input; Right Side CVBS Input(VL4510C only)
Output Rear Panel Connections:
10/100/1000 TS Port Gigabit Ethernet Transport Stream Output via SFP Interface
DVB ASI Output Available only on VL4510 models.
QAM Output Available only on VL4510Q model
Ethernet Management Port
The Ethernet Management Port is used for monitoring, firmware upgrades, and
command line interface to configure the unit.
V L 4 5 0 0 U S E R M A N U A L R E V . 3 . 0 0 . 0 6 1
Radiant Communications Corporation 2017
7
Power Input
12V DC Input Pin1(GND), Pin2(+V), 12VDC@4A Power Supply
Chassis GND Lug
Encoding Profiles
MPEG2
h.264
PROFILE
MPEG-2 MP@ML/HL
AVC H.264 L3.0 and 4.2
CHROMA
4:2:0
4:2:0
RESOLUTION
480i, 480p, 720p, 1080i
and 1080p
480i, 480p, 720p, 1080i and 1080p
FRAME RATE
24, 25, 29.97, 30, 59.94
and 60fps
24, 25, 29.97, 30, 59.94 and 60fps
ASPECT RATIO
4:3 and 16:9
4:3 and 16:9
PICTURE TYPE
IP, IPB, IPBB
IP, IPB, IPBB, IPBBB
GOP SIZE
10-60 frames
10-240 frames
GOP STRUCTURE
IBB or BBI
IBB or BBI
VIDEO BITRATE
1.5-24M
500k-24M
VIDEO SCALING
UP/DOWN Conversion
UP/DOWN Conversion
AUDIO ENCODING
AC3 2.0, MPEG Layer II.
and AAC
AC3 2.0, MPEG Layer II. and AAC
AUDIO SAMPLING
RATE
48kHz
48kHz
AUDIO BIT RATE
96-384kHz
96-384kHz
Output Interfaces
IP: SFP Interface
1000B RJ45 Module
Gigabit SFP Optical Module
DVB ASI Output, 75Ohm BNC Connector with 54M max rate
TS: MPEG2 TS, User Selectable Rate, Full PID Table including TS ID, Program ID, Video, Audio,
PMT and PCR PIDs, ATSC and DVB modes.
V L 4 5 0 0 U S E R M A N U A L R E V . 3 . 0 0 . 0 6 1
Radiant Communications Corporation 2017
8
Energy Specifications
By using advanced encoding algorithms Radiant achieves superior video quality at low bitrates with
extremely Low Power Consumption and Heat Dissipation.
Total power consumption is 24W per 1080p and 480i dual stream at full 19M TS bitrate.
The temperature inside and outside of the unit will not exceed 40⁰C. Cooling is provided by two fans
located on the front left side of the unit.
V L 4 5 0 0 U S E R M A N U A L R E V . 3 . 0 0 . 0 6 1
Radiant Communications Corporation 2017
9
Installation
The VL4500 chassis can be mounted in a standard EIA, 19” rack.
Secure the Encoder’s front panel to the rack by inserting four machine screws, with cup
washers, through the four mounting holes in the front panel.
When installing one or more encoders in a headend rack, it is recommended to leave a 1 rack
unit space (1.75” high) between units to maximize air flow.
To power up the unit, connect the 12VDC power supply to the unit.
If both power sources are connected they will act as redundant power supplies.
The POWER LED on the front-panel will light green and the LCD screen will turn on.
The standard boot-up time is less than one minute, after successful boot-up the LCD screen will
read “VL4500”
2
V L 4 5 0 0 U S E R M A N U A L R E V . 3 . 0 0 . 0 6 1
Radiant Communications Corporation 2017
10
V L 4 5 0 0 U S E R M A N U A L R E V . 3 . 0 0 . 0 6 1
Radiant Communications Corporation 2017
11
Communication
The Encoder can be controlled and managed with either the out-of-band network port located on
the front panel or via the RS232 serial port. In-band management through the TS port is possible as
well.
Network Management
Initially, the simplest way to setup the networked PC to communicate with the VL4500 is to put the PC
on the same subnet as the VL4500. The default IP address of the VL4500 management port is:
192.168.16.252
NOTE: The static IP of the computer cannot be the same as the static IP of the VL4500.
The following steps explain how to change the IP address of a computer running windows7:
1. On your computer, open the "Control Panel"
2. Click on “Network and Internet”
3. Click on the "View network status and tasks"
4. Click on “Change Adapter Settings” on left hand side of the window
5. Right-click on the "Local Area Connection", and then click on the "properties".
6. A dialog box entitled "Local Area Connection Properties" will appear. In this box, double-
click on the "Internet Protocol Version 4 (TCP/IPv4)".
7. A dialog box entitled "Internet Protocol Version 4 (TCP/IPv4) Properties" will appear.
8. Select the "Use the following IP address" option and enter the following addresses:
IP address: 192.168.16.2
Subnet mask: 255.255.255.0
9. Click OK to close the dialog box. Now your computer is ready to communicate with the
unit.
10. Open an Internet Explorer web browser on your computer and enter the following URL
3
V L 4 5 0 0 U S E R M A N U A L R E V . 3 . 0 0 . 0 6 1
Radiant Communications Corporation 2017
12
http://192.168.16.252
V L 4 5 0 0 U S E R M A N U A L R E V . 3 . 0 0 . 0 6 1
Radiant Communications Corporation 2017
13
Configuration
The VL4500 Web management system is accessible through both TS and MGMT Ethernet interfaces.
Settings are grouped by tabs for:
Video Settings
Audio Settings
TS Settings
Network Settings
System Settings
User Presets
Note:
Changed settings will take effect only after the Encoder is started or restarted via the buttons on
the bottom of the screen.
Settings can be saved to a desired preset; preset includes also the current state of the Encoder
The encoder is being shipped with encoder factory preset. Saving on that preset is not possible. A new
preset should be created, configured and then saved.
4
V L 4 5 0 0 U S E R M A N U A L R E V . 3 . 0 0 . 0 6 1
Radiant Communications Corporation 2017
14
The top portion of the web based management screen provides information about part number,
firmware version, uptime and unit name.
Bottom portion provides control to Stop, Start, Restart (soft reboot) the encoder, as well as creating
new presets, changing presets and saving them.
V L 4 5 0 0 U S E R M A N U A L R E V . 3 . 0 0 . 0 6 1
Radiant Communications Corporation 2017
15
Video Settings
Under Video Settings tab, the user can set specific codec parameters and SDI Video Input signal
information, that includes Input resolution and frame rate. Supported are:
1080p at 24, 29.97, 30 and 59.94fps (H.264, 1 x 3G mode only)
1080i at 24, 29.97 and 30 fps
720p at 29.97, 30, 50, 59.94 and 60 fps
480i at 29.97 and 30 fps
V L 4 5 0 0 U S E R M A N U A L R E V . 3 . 0 0 . 0 6 1
Radiant Communications Corporation 2017
16
The detected resolution and frame rate are shown on the web page under Video Input.
The output resolution follows the input resolution of the incoming SDI signal or it could be forced. In
case that the output resolution is forced the input, signal must have the same resolution as the input.
VL4510C unit supports either SDI or composite video input. Selection of the active video input can be
done from the dropdown menu of Input Source parameter. Save the new video input source prior of
restarting or starting the unit.
For multichannel versions of the unit the selections of active SDI video inputs and audio inputs for and
encoder instance must match, i.e. video and audio input source must point to the same location!
Encoding field order can be selected to either TFF (top field first) or BFF (bottom field first). When down
converting from HD to SD with QBA support for old legacy STB, set the filed order to TFF for the SD
encoder.
H264 encoding is supported only in BFF field order.
V L 4 5 0 0 U S E R M A N U A L R E V . 3 . 0 0 . 0 6 1
Radiant Communications Corporation 2017
17
The VL4500 encoder supports the following bitrate ranges:
MPEG2 HD resolution Range from 7M to 25M
MPEG2 SD resolution Range from 1M to 15M
H264 HD resolution Range from 2M to 25M
H264 SD resolution Range from 500k to 25M
The bitrate is adjustable in 100K increments, see the table below for recommended settings:
Output Stream(s)
Video 1 (HD/SD),
kbps
Audio,
kbps
Output Bitrate,
kbps
MPEG2, 1080p SPTS
16000
192
19600
h.264, 1080p SPTS
12000
192
13500
MPEG2, 1080i SPTS
12000
192
15000
h.264, 1080i SPTS
8000
192
9500
MPEG2, 720p SPTS
9000
192
12000
h.264, 720p SPTS
6000
192
7500
MPEG2, 480i(p) SPTS
3500
192
5000
h.264, 480i(p) SPTS
1500
192
2000
The user can select the aspect ratio, scaling mode for HD to SD down-conversion and rate control for
the encoder.
The supported video ratios are 16: 9 (widescreen) and 4:3 (normal).
Both CBR (constant bit rate) and VBR (variable bit rate) encoding are supported.
Under VBR rate control the encoder will vary the number of bits used
to represent a frame so that the overall average amount of bits-per-
frame is achieved. It does this by taking bits from frames with less
information to encode (that don't need them) and giving them to
frames that have more information to encode (and does need them). With CBR each frame uses the
same number of bits regardless of whether it needs them or not.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54

Radiant Communications VL4500 SRT Encoder User manual

Category
Noise Reduction Machine
Type
User manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI