Procedures for
firmware and
criteria updating in
MagicSat Easy/Flat
Sat Easy systems
GB
Procedures for firmware updating in MagicSat Easy/Flat Sat Easy systems
To carry out firmware (basic software) updating in MagicSat Easy/Flat Sat Easy systems
you are requested to:
• Use a Microsoft Windows operating environment (2000, Xp)
• Download and Install the USB driver for Teleco products, available at the following
link http://www.support-telecogroup.com/software/InstallTelecoUsbDriver.exe
• Download and Install the programming software available at the following link:
http://www.flashmagictool.com/download.html&d=FlashMagic.exe
• Download and Install the microcode (firmware), available at the following link :
http://www.support-telecogroup.com/software/InstallMagicSatEasyFirmware.exe
• Once the individual software packages have been installed, use a USB cable to
connect the MagicSat Easy/Flat Sat Easy to your computer and wait for correct
recognition by your computer.
• Check on which virtual COM port the MagicSat Easy system appears to be
recognised (in the example, it appears as visible on the COM3 port).
• Start the previously installed FlashMagic software and configure it as shown below:
• Specify the port in use at point ‘Step 1’ (in this case, it is the port COM3) and
specify the location of the firmware to use at point ‘Step 3’ (in this case, we advise
to use the ‘Browse’ key to select it). If, during firmware installation, a different root
had not been specified, the file will be located within the structure
‘C:\TELECO\MagicSat Easy\Firmware’.
• Switch off MagicSat Easy/Flat Sat Easy and wait for your computer to notify
removal of the USB peripheral unit (notification is done via a sound tone of the ‘bi-
bo’ type).
• Press the little black button provided on the back of the MagicSat Easy/Flat Sat
Easy ControlBox next to the power input connector, and hold it down while
switching the system back on. Wait for USB peripheral acknowledgement (notified
by a ‘bo-bi’ type sound), then press the START key (Step 5) of the FlashMagic
software. Once the programming sequence has started (special messages will be
displayed in the bottom part of the program status bar), the little black button can be
released.
• At the end of the firmware updating procedure (indicated by the ‘finish’ message
displayed in the bottom part of the status bar), switch the MagicSat Easy/Flat Sat
Easy off, disconnect all the connections and shut down all active programs.
• Your MagicSat Easy/Flat Sat Easy has now been updated.
Procedure for criteria updating in MagicSat Easy/Flat Sat Easy systems
To carry out criteria updating in MagicSat Easy/Flat Sat Easy systems you are requested
to:
• Use a Microsoft Windows operating environment (2000, Xp)
• Download and Install the USB driver for Teleco products, available at the following
link http://www.support-telecogroup.com/software/InstallTelecoUsbDriver.exe
• Download and Install the programming software available at the following link:
http://www.support-telecogroup.com/software/InstallMagicSatEasy.exe
• Download and Install your required criteria available at the following link:
http://www.support-telecogroup.com/telecogroup/teleco/it/software.asp?D=1&L=ITA
and then select a criterion
• Once the individual software packages have been installed, use a USB cable to
connect the MagicSat Easy/Flat Sat Easy to your computer and wait for correct
recognition by your computer.
• Check on which virtual COM port the MagicSat Easy system appears to be
recognised (in the example, it appears as visible on the COM3 port).
• Start MagicSat Easy Client software execution and configure the port in use to be
like the virtual COM port (in this case, COM3).
• Shut down and the restart the software
• To transfer a new set of criteria and update your MagicSat Easy/Flat Sat Easy,
download the file containing the new parameters by using the Software function
‘Open file’ then select the new set of criteria (if a different destination root had not
been specified, the new criteria will be available at ‘C:\TELECO\MagicSat
Easy\Criteria’)
• After loading the new set of criteria, switch on your MagicSat Easy/Flat Sat Easy
and wait for the software to recognise it.
• It is now possible to transfer data by pressing the item menu ‘Send Data’. A
‘transfer in progress message’ will be displayed
• Upon transfer completion, the message will disappear and it will be possible to
switch off MagicSat Easy/Flat Sat Easy and disconnect it from the computer.
• Updating is now completed. Additional information on software functions will be
available by pressing the function key F1
ITALY
Via E.Majorana 49
48022 LUGO( RA )
Tel. + 39 0545 25037
Fax.+ 39 0545 32064
E-mail:
www.telecogroup.com
Procedures for firmware and criteria updating in
MagicSat Easy/Flat Sat Easy systems
/
