Teleco Magic Sat Super Digital 2 CI User manual

Vers.002

INSTALLATION GUIDE AND USER MANUAL

OF THE

MAGIC SAT SUPER DIGITAL 2 CI

GB

Table of Contents

Magic Sat Super Digital 2 CI Vers. 002

2

Table of Contents

Table of Contents ................................................................................................................ 2

Information ........................................................................................................................... 4

Technical specifications ....................................................................................................... 5

Definition .......................................................................................................................... 5

Technical specifications ................................................................................................... 5

Tuner ............................................................................................................................ 5

MPEG demodulator ...................................................................................................... 5

Conditioned access ...................................................................................................... 5

Output connections ...................................................................................................... 5

RF modulator ................................................................................................................ 5

Searching Time ............................................................................................................ 6

Power supply ................................................................................................................ 6

Dimensioni unità di comando ....................................................................................... 6

List of Accessories ............................................................................................................... 6

Assembly instructions .......................................................................................................... 8

Installation with cables led through the middle of the base ............................................ 10

Installation with lateral cable output ............................................................................... 12

Connections ................................................................................................................... 13

User manual Magic Sat Super Digital Operation System .................................................. 16

Satellite seeking ............................................................................................................. 16

Programme seeking ....................................................................................................... 16

Antenna lowering ........................................................................................................... 16

Additional operations ......................................................................................................... 17

Changing satellites during search .................................................................................. 17

Safety function ................................................................................................................... 17

Important information ......................................................................................................... 18

TIPS on the best use ......................................................................................................... 19

Trouble-shooting ................................................................................................................ 19

DIGITAL RECEIVER ......................................................................................................... 20

Remote Control .............................................................................................................. 20

Front view ...................................................................................................................... 22

Rear view ....................................................................................................................... 22

Information about safety .................................................................................................... 24

Installation tips ................................................................................................................... 25

Receiver installation .......................................................................................................... 25

Introduction .................................................................................................................... 25

Main connections ........................................................................................................... 25

Connecting the lead from the satellite dish ................................................................. 25

Connecting the SCARTcable between the receiver and the TV or monitor ................ 25

Connecting the coaxial cable between receiver and TV ............................................. 25

Connecting the remote control infrared sensor ........................................................... 25

Table of Contents

Vers. 002

Magic Sat Super Digital 2 CI

3

Connecting to the power supply ................................................................................. 26

Additional connections ................................................................................................... 26

Connecting to a video recorder ................................................................................... 26

Connecting to a monitor in S-VHS .............................................................................. 26

Connecting a Home Theatre system .......................................................................... 26

Immediate use of the receiver ............................................................................................ 27

Introduction .................................................................................................................... 27

Switching on the receiver ............................................................................................... 27

Changing service............................................................................................................ 28

Favourites lists which were factory-loaded ..................................................................... 29

Other immediate functions ............................................................................................. 29

Menu and advanced functions ........................................................................................... 31

Introduction .................................................................................................................... 31

Accessing the menu ....................................................................................................... 31

The favourites list ........................................................................................................... 32

Creating a list .............................................................................................................. 32

Modifying a list ............................................................................................................ 34

Deleting a list .............................................................................................................. 37

Installation ...................................................................................................................... 37

Antenna/Satellite configuration ................................................................................... 38

Antenna configuration ................................................................................................. 39

Satellite configuration ................................................................................................. 40

Adding a new satellite ................................................................................................. 41

Modifying the satellites list .......................................................................................... 42

Deleting a satellite ...................................................................................................... 42

- Deleting a satellite ...................................................................................................... 42

Adding a transponder ................................................................................................. 43

Deleting a transponder ............................................................................................... 43

LNB configuration ....................................................................................................... 44

Motor configuration ..................................................................................................... 44

Magic Sat Configuration ............................................................................................. 45

Service installation ...................................................................................................... 46

TV configuration.......................................................................................................... 48

Set time ...................................................................................................................... 49

VCR configuration....................................................................................................... 50

Reinstallation .............................................................................................................. 50

System update ............................................................................................................ 51

User settings .................................................................................................................. 51

Language configuration .............................................................................................. 52

Access control ................................................................................................................ 53

Modifying the PIN code ............................................................................................... 53

Information system ......................................................................................................... 54

Conditioned access ........................................................................................................ 54

Reinstalling your receiver ................................................................................................... 57

Introduction .................................................................................................................... 57

Re-installation sequence ................................................................................................ 57

Glossary ............................................................................................................................. 62

Information

Magic Sat Super Digital 2 CI Vers. 002

4

Information

Congratulations on purchasing our Magic Sat Super Digital, one of the most

technologically advanced products in the satellite TV reception field. This handbook has

been drawn up to provide information on installation, use, maintenance and technical

specifications for your Magic Sat Super Digital system:

Issue date: October 20, 2005

Document revision: Magic Sat Super Digital rev. 2.0

Software revision: 2.4

Should you require further information please contact your local dealer or:

TELECO s.p.a.

Via E. Majorana 49

I-48022 LUGO (RA)

Web site: www.telecogroup.com

Technical Assistance: [email protected]

Technical Assistance: 899.899.856

TELECO s.p.a. shall not be held responsible for any errors in drawing up this manual. All

information which is contained herein is updated on the date of issue and the

aforementioned revisions. TELECO s.p.a. reserves the right to make modifications

according to technological changes.

Technical specifications

Vers. 002

Magic Sat Super Digital 2 CI

5

Technical specifications

Definition

Digital receiver in compliance with DVB-S and DVB-CI specifications and EN 300 421, TR

101 198, EN 50221, TS 101 699 standards.

 up to 5000 saveable services.

 256-colour OSD.

 SP-DIF audio output.

 2 SCART sockets.

 One S-VHS output

 Aux audio output

 RS232 port for software update and service list management.

 Software can be updated via satellite.

 DataPort for connection with other TELECO devices.



Technical specifications

Tuner

 F IEC169-24 female connector

 Working frequency 950 2150 MHz

 Rated input impedance 75 Ω

 Acceptable signal level from –25 to –65 dBm.

 DiSEqC control version 1.0 and 1.2

 QPSK modulation

 Symbol rate from 2 to 31 Ms/s

 FEC from 1/2 to 7/8

MPEG demodulator

 Video MPEG-2 ISO/IEC 13818

 Video compression MPEG-2 ML@MP

 Screen format 4/3 and 16/9

 Resolution 720 x 576

 MPEG Musicam Layer I and II audio decode

Conditioned access

 2 PCMCIA slots

Output connections

 TV SCART video output CCVS and RGB

 VCR SCART output CVBS and input CVBS and RGB

 MiniDIN connector for s-VHS

 Aux. L/R audio in Cinch

 S/PDIF digital audio in Cinch

 RS232C 9-pin, type SubD

 MiniFITJ connector for motor unit ( 2X )

RF modulator

List of Accessories

Magic Sat Super Digital 2 CI Vers. 002

6

 Male/female RF IEC 169-2 connector 75 Ω

 Working frequency 470 – 860 Mhz (21 – 69 channels)

 PAL I/G/K/M system selectable from menu

Searching Time

 Automatic Searching Time: min 20 sec - max 5 min, depending on the place you

are at and the battery status (if the battery is not fully charged, searching takes

longer)

Power supply

 Stabilised 12V DC power supply, -20 +20 %

 Maximum consumption: on search < 5A

on reception < 1A

Dimensioni unità di comando

 (L x H x D) 310 x 70 x 200 mm

 Weight 1.7 kg

 Working temperature from 0 to 45 °C.

 Storage temperature from 0 to 70 °C.

 To be stored at a relative humidity of 5 - 95 % (not condensable)

List of Accessories

Magic Sat Super Digital is delivered inside a cardboard case that has been specially made

to protect it from knocks and pressure. The following accessories are supplied:

1

External motor-driven unit

2

50 - 65 - 85 cm dish

3

Universal LNB

4

Control unit (receiver)

5

Remote control complete with two AAA batteries

6

Motor Connection Cable

7

Antenna-Control unit connection lead

8

Power Supply Cable

9

Remote Control Expander

10

Control unit/ TV set connection cable

11

Waterproof box to pass leads through to interior

12

Heat-shrinking sheaths

13

Roof attachment plate

14

No. 4 stainless steel Locknuts M6

15

No. 4 stainless steel Screws and Locknuts – M5  Ø 50 cm / M 6  Ø 65-85 cm

16

User’s manual

RECYCLING:

with a view to reducing disposal of waste

electrical and electronic equipment as much as possible,

do not throw out this end of life cycle appliance together

with other unsorted municipal waste, but make use of a

recycling centre.

List of Accessories

Vers. 002

Magic Sat Super Digital 2 CI

7

Important notice

Due to transport reasons, Magic Sat Super Digital comes packaged in two separate

cartons:

a) The first item contains the driving unit with all the cables and the control unit.

b) the second item only contains the dish.

It is essential to check that the dish has not been damaged during transport when the

package is opened. In particular, check the following well:

• By resting the dish edge against a flat surface (e.g. the floor or a wall) check that it

makes contact to the surface all around. If it is not so, try and make the edge level,

without denting the dish, or call our After-Sales.

Assembly instructions

Magic Sat Super Digital 2 CI Vers. 002

8

After checking that everything is in order, install the dish on the driving unit as follows:

1) Temporarily connect the Control unit to the driving unit through the grey motor cable.

2) Power both the Control unit and the receiver using a battery.

3) Press the Red button (ON/OFF) in the remote control and extend the dish support

mast.

4) Press the " STOP " button in the remote control to lock the mast in a vertical position.

5) Secure the dish to the mast and screw down the four supplied screws.

6) Press the " DOWN " button in the remote control and lower the antenna.

7) Disconnect the Control unit, the battery and install Magic Sat Super Digital on the

vehicle.

Assembly instructions

1) Position the Control unit in a compartment near the TV set

2) Fix the MIR remote control Extension to a wall or your TV-set and connect it to the

Control Unit (Fig.1 – page 9).

3) On the roof of the vehicle, choose a free area large enough to allow the antenna to

revolve (Fig.2 – page 9).

4) Install the (Grey and White) connection cables to reach the OUTDOOR installation

area.

Assembly instructions

Vers. 002

Magic Sat Super Digital 2 CI

9

5) Clean the roof carefully in the area the OUTSIDE UNIT is to be installed in.

6) Remembering that the OUTSIDE UNIT must be fastened as shown on Figure 3,

remove the BASE PLATE from the outside unit, unscrewing all 4 nuts. Position the

base plate as Fig.4 with the short side towards the driving direction of the vehicle (Fig.

4).

7) Clean the lower part of the BASE PLATE carefully, applying a layer of glue on the

whole surface (e.g. SIKAFLEX).

8) Fasten the Base Plate to the roof (short side towards the driving direction of the

vehicle), now fasten the external powered unit to the four stud bolts of the plate, using

the four nuts supplied with the equipment.

Assembly instructions

Magic Sat Super Digital 2 CI Vers. 002

10

9) Apply a layer of silicone all around the BASE PLATE in order to make it completely

(Fig. 5)

Installation with cables led through the middle of the base

10) Connect the Grey and White cables coming from inside the vehicle (Fig. 6) to both

cables of the outside unit, making them watertight using two pieces of

THERMORETRACTILE TUBE (Fig. 7).

WARNING While performing this operation, do not pull forcefully on the cables coming

from the middle of the outside unit, in order not to risk pulling them out.

8

Assembly instructions

Vers. 002

Magic Sat Super Digital 2 CI

11

11) Install the OUTSIDE UNIT on the plate, bearing in mind that:

a) The proper position must be as in (Fig. 9).

b) Coat both the base plate and the driving unit bottom (Fig. 10) with a thick layer of

silicone to prevent any water infiltration. Screw in the four supplied nuts at the screws

and tighten as required (Fig. 11).

Assembly instructions

Magic Sat Super Digital 2 CI Vers. 002

12

Installation with lateral cable output

12) Fasten the OUTSIDE UNIT to the base plate. Lead both cables out of the 4 grooves

and respect the positions shown on. Figure 12.

CAUTION: during this operation, do not pull either cable forcibly, as they could come out.

13) Connect both cables coming from the centre of the OUTSIDE UNIT to the extensions.

Waterproof the connectors using both pieces of heat-shrinking pipe Fig. 13.

14) Fit the cables into a raceway up to the point where the cables enter the vehicle Fig.

14.

15) Carefully seal the hole where the cables pass into the vehicle to prevent water from

coming in. Fig. 14.

Assembly instructions

Vers. 002

Magic Sat Super Digital 2 CI

13

Connections

16) Connect the (motor) grey cable to the MOTOR UNIT Connector and the white

(antenna) coaxial cable to the ANTENNA Connector in the Control. (Fig. 15).

17) Connect the MIR remote control Extension to the IR REMOTE connector in the

Control Unit. (Fig. 15).

18) Connect the BLACK power supply cable of the CONTROL UNIT to the NEGATIVE

POLE of the vehicle 12 Volt battery, and the RED cable to the POSITIVE POLE +

(remember not to mix the + and - poles up), using 2 cables of a diameter of 2,5 mm (5

mm

2

cross-section). (Fig. 15).

19) The GREEN safety cable of the Control Unit must be connected to the consensus of

the vehicle startup console (in many cases such consensus is located on Pin 15 in the

main terminal board). In this way, whenever the motor is started, this cable receives a

positive + 12 Vdc voltage, which will automatically lower the antenna and lock all

functions of the Control Unit simultaneously (Fig.15).

Any connection made in points other than as indicated (e.g. on

the alternator) can give rise to equipment malfunction and/or damage resulting in loss of

the warranty.

MIR

15

Assembly instructions

Magic Sat Super Digital 2 CI Vers. 002

14

20) Insert one end of the SCART cable in the TV connector of the Control Unit and

connect the other end to the TV set (Fig. 16)

21) Inside the Control Unit are:

a) Control ELECTRONICS of the outdoor unit motors.

b) DVB Digital Receiver.

16

Digital receiver

–

to

television connection

Assembly instructions

Vers. 002

Magic Sat Super Digital 2 CI

15

WARNING

This technical note is to call the attention of the installation personnel to certain

details of Magic Sat Super Digital installation. During installation, you must take the

following precautions:

The power supply cable must come directly from the battery and be of a minimum cross-

section of 5 sq.mm. Only the Magic Sat Super Digital must be connected to this cable; all

the other devices must be connected to another power supply cable.

The cable connecting the driving unit to the Magic Sat Super Digital Control Box must

NEVER be cut for any reason whatsoever: should the cable turn out to be too long, wind

the extra part into a coil in a free area of the vehicle.

Leave a little cable in the driving unit area; should any technical operation be required, it

will make

it easier to remove the driving unit.

Also, before checking its operation, we suggest you make sure that:

The outside converter (also called LNB) has been installed properly and locked into its

plastic lock nut. Remember that the outside converter has its own assembly position which

must be complied with. Otherwise you will not receive any signal.

The preset assembly position of the converter is along the median line of the dish (Fig. A)

and in this configuration the Magic Sat Super Digital system operates properly in most

European countries. If however you are in areas which are very far from the orbital position

of the satellite, you could need to adjust the angle of the converter. In particular, if you

wish to receive any transmission from the Astra 19E, Astra 28E or Hot Bird 13E satellites

and you are in Portugal or Morocco, you should adjust the converter angle as shown on

fig. B2, whereas if you are in Turkey, you should set the converter on the B1 position for

the same satellites.

Below you will find a table to help you setting the best angle Place Position HotBird13E

Astra 19E ASTRA 28E

User manual Magic Sat Super Digital Operation System

Magic Sat Super Digital 2 CI Vers. 002

16

User manual Magic Sat Super Digital Operation System

Magic Sat Super Digital is a fully automatic satellite tracking system. It is able to track

satellites which transmit DIGITAL signals.

All information about operation are shown on the TV screen upon turning the system on. In

order to give all users easy access to this sytem, we tried to make operations simpler:

• satellite searching

• required program searching

• antenna lowering

Satellite seeking

When Magic Sat Super Digital is off (Antenna down), press the Red button (ON/OFF) on

the remote control to start the searching procedure which ends when the TV pictures

appear.

Programme seeking

Once the antenna has been pointed to the required satellite, radio and television stations

can be received by simply shifting programs with the remote control. To receive programs

from other satellites, you will just have to key in the number of your required program on

your remote control, or select it from the program list. Magic Sat Super Digital will then

search for the next satellite and store the corresponding antenna position.

Antenna lowering

When Magic Sat Super Digital is on (antenna is up), press the (yellow) DOWN button to

bring the antenna down and switch the system off.

As long as the antenna is coming down, the following message is brought to the display:

Followed by:

When the antenna reaches its horizontal position, Magic Sat Super Digital will go off and

TV messages will disappear. Should you forget to lower the antenna before starting up

with your road vehicle, don't worry: the moment you turn the engine ignition key, a special

safety circuit will lower the antenna automatically, keeping it locked in place as long as the

vehicle moves. This however is possible only if the special Green cable has been

connected to the ignition key at the time

N.B. Because of this safety function, remember that if you decide to turn the engine on in

order to charge the batteries of the vehicle, the Magic Sat Super Digital will automatically

bring the antenna down; as long as the engine is running, it will not be possible to perform

searching.

Antenna parking

Antenna Parked

Additional operations

Vers. 002

Magic Sat Super Digital 2 CI

17

Additional operations

1) With the antenna pointed to a satellite, the Control unit may be turned off (by pressing

the Red push-button) (ON/OFF) without having to lower the antenna. In this case, the

total consumption by the system Magic Sat Super Digital will be cut down to less than

1A.. To power the Control unit back on, just press the Red push-button (ON/OFF) on

the remote control once again.

2) If the antenna is in motion, the red push-button (ON/OFF) will not be working to

prevent the Control unit being switched off which would make satellite searching

ineffective.

3) In the event that Magic Sat Super Digital does not find the selected satellite, it will stop

the antenna at the end of its stroke (either all the way out or all the way in) and show

the message " Failed Search ". If this happens, the antenna can be lowered by

pressing the DOWN push-button or a program transmitted by another satellite can be

selected.

Changing satellites during search

The Magic Sat Super Digital always starts its automatic search by examining the satellite

which transmits the last programme chosen before turning the system off (e.g. Astra,

Channel 1). Should you wish to launch an automatic search for another satellite, proceed

as follows:

• Press the RED (ON/OFF) key on the remote control to swhitch on the system.

• Press the STOP key to stop the antenna temporarily (the words "Search suspended"

will be displayed on the TV set)

• Choose the new channel transmitted by the satellite you want (e.g. Channel 117, Hot

Bird)

• After a few seconds, the antenna will start searching again and will stop on the new

satellite (Hot Bird).

WARNING: if the antenna is stopped with the STOP button, this can ONLY be restarted if

a programme transmitted by another satellite is selected.

Safety function

If, for any reason (trees, ice, etc.), the antenna is not able to move freely during the

operation, it will stop at once and the following message will be displayed:

After having verified the reason for the blockage, press the DOWN key and then remove

the cause.

Motors Locked

Important information

Magic Sat Super Digital 2 CI Vers. 002

18

Important information

for proper antenna pointing

1) Before performing antenna pointing, make sure you have positioned your vehicle so

the view towards the South (where Satellite signals come from) is free from any

nearby obstacle (trees, houses, etc.). This way, the antenna will be free to receive

signals coming from the satellite.

2) It is also important to know that satellites do not transmit with the same intensity

throughout Europe, so if you are outside the reception area, your Magic Sat Super

Digital search might be unsuccessful. The reception areas for each Satellite can be

found on the main magazines dealing in this line of business. Also remember that the

larger the dish, the more reception area

WRONG POSITION

RIGHT POSITION

TIPS on the best use

Vers. 002

Magic Sat Super Digital 2 CI

19

TIPS on the best use

When you park your vehicle, make sure that:

1) No obstacle (for example trees) is too near your antenna, preventing it from moving

freely. No metal or glass wall is very near (about 5 m) the antenna, since this would

act as a mirror for satellite signals and could induce the antenna to point towards it.

2) In case of snow or ice actuating the Magic Sat Super Digital free it in order to avoid

wasting battery power in order to lift it.

3) If you decide to turn the engine of your vehicle on in order to re-charge its batteries,

with the safety cable connected to the ignition key, the antenna, if lifted, will come

down automatically and it will not be possible to lift it again as long as the engine is

running.

4) Make sure that your batteries are always sufficiently charged, since, if the voltage falls

below 10 Volts, the Magic Sat Super Digital electronic safety circuit will prevent the

antenna from rising.

5) Should you use 12 Volt feeders instead of batteries in order to feed the Magic Sat

Super Digital, be careful to use high quality stabilized feeders with a supplied power of

at least 10A. At all costs, avoid using low quality, non stabilized battery feeders.

Trouble-shooting

If the Magic Sat Super Digital has not found the satellite after a complete search, check

the following:

a) Is the view towards the South free from any obstacle?

b) Is the place you are at within the reception area of the satellite you have chosen?

c) Is the cable connecting the LNB to the antenna firmly fastened? It could have been

ripped off or come loose because of contact with an unexpected

d) Are all the connections on the Control Unit properly set up?

If the antenna has stopped after performing pointing, but neither messages nor images

appear on the screen:

a Is the SCART cable connected?

b If the TV set is not connected by a SCART cable, but is connected by a COAX cable

to the TV socket, have you chosen the right programme on

If the antenna does not move when you press the Red push-button, check the

a) Are the RED and BLACK cables properly connected to the battery? The RED cable

must be on the + pole, the BLACK cable on the - pole.

b) Should you have mixed up the cables, first disconnect them, replace the safety fuse

on the bottom of the Control Unit using a similar one (10 A), then re-connect the

RED and BLACK cables properly to the battery.

c) Is the engine on your vehicle running? Turn it off, since this means the safety

system which keeps the antenna down is operating.

DIGITAL RECEIVER

Magic Sat Super Digital 2 CI Vers. 002

20

DIGITAL RECEIVER

BUILT IN THE CONTROL UNIT

Remote Control

ON / OFF

Mute

EPG

TV/RADIO

Right, left, up, down

and OK keys

Menu

Page +

Exit

Audio

FAV

Favourites list

Info

Pause

DOWN

STOP

Page -

Numerical keys

Page is loading ...

Teleco Magic Sat Super Digital 2 CI User manual

Teleco Magic Sat Super Digital 2 CI User manual

Related papers

Other documents