EG8-PTZ-IP, IP-Enabled 8”
Environmental Globe PTZ
Instruction Sheet
PROPERTY OF WREN Page 1 of 3 7L247 REV-B 10-09-2006
124 WREN PARKWAY • JEFFERSON CITY, MO 65109 • TOLL FREE (800) 881-2249 • FAX (877) 893-2317
www.wrensolutions.com
Overview
The IP-Enabled Environmental Globe (EG8) is an attractive, durable solution
for outdoor applications accommodating a pan-tilt-zoom camera. It is an ideal
solution for situations where reliability and aesthetics are important such as
retail, property management, commercial and industrial facilities
Suggested Installation Equipment
1. #2 Phillips-head screwdriver
2. Outdoor-approved pipe thread sealant (included)
Component List [Figure 1]
A. Housing (double wall)
B. IP Encoder Module
C. Camera Mounting Plate Assy (with optional heater/blower and
circuit board)
D. PTZ camera
E. Dome Assy
F. Foam Dust Plug (not shown)
G. Dome Safety Tether (not shown)
H. Mounting Plate Safety Tether (not shown)
I. Pipe Thread Sealant (not shown)
Warnings and Safeguards
Prior to installation and use of this product, please observe the following
warnings
1. Installation and servicing should be done by qualified personnel, and all work
done should conform to local codes.
2. Using replacement parts or accessories other than Wren may invalidate the
warranty.
3. Use only Wren-approved replacement parts or supplied accessories. Failure to
comply may invalidate remaining warranty period.
4. Verify proper location and installation of the housing mount
(1½” NPT pipe
or approved mount).
The pipe or mount shall be capable of supporting three
(3) times the weight of the housing and its contents.
5. Verify proper installation of cabling to support camera power and
communication requirements for fixed camera applications.
Outdoor IP Solutions
EG8-
PTZ-IP
8” Environmental Globe
PROPERTY OF WREN Page 2 of 3 7L247 REV-B 10-09-2006
124 WREN PARKWAY • JEFFERSON CITY, MO 65109 • TOLL FREE (800) 881-2249 • FAX (877) 893-2317
www.wrensolutions.com
6. The EG8 is designed to be operated by a 24VAC power source
Installation
1. Remove the dome.
2. Disconnect the PTZ camera from its base by pushing in and twisting
counter clockwise. Set aside.
3. Apply thread sealant (included) to the 1½” NPT pipe threads or
approved mount. This procedure will prevent moisture ingress through
the threads. [Figure 2]
WARNING
Failure to properly seal the 1½” NPT pipe
threads will permit water to enter the housing
and may damage the internal equipment.
4. Install EG8 assembly on 1½” NPT pipe or mount by rotating counter-
clockwise until threads are fully engaged.
5. Detach the camera mounting plate from the housing and allow it to be
suspended by tether.
6. Remove foam dust cap and route CAT5 and power cables into the housing.
7. Connect 24VAC to the input terminals on circuit board marked “+IN-.”
[Figure 3]
8. Insert end of CAT5 into the RJ45 jack in the IP encoder module. [Figure
4]
9. Push extra wire length up through housing flange and re-install the foam
dust cap in the cable entrance of the housing.
10. Reinstall and tighten the screws holding the camera mounting plate.
11. Reconnect the PTZ camera to its base on the camera mounting plate by
pressing onto the plate and turning clockwise.
12. Reinstall dome assembly and tighten screws to ensure a proper seal with
the dome gasket.
Electrical Properties
• Input Voltage = 24VAC ± 10%
• Power = 2.5A @ 24VAC (w/ heater on)
• Blower = 4.7 CFM (2.2 watts) (continuous operation)
•
Heater = 40 watts
Optional Mounts (consult factory for color and style options)
• Curved Wall Mount HM11xx
•
Pole Mount HM12xx (requires HM11xx)
•
Corner Mount HM13xx (requires HM11xx)
• Roof (Parapet) Mount HM14xx (requires HM11xx)
FIGURE 3
FIGURE 4
FIGURE 1
FIGURE 2
PROPERTY OF WREN Page 3 of 3 7L247 REV-B 10-09-2006
124 WREN PARKWAY • JEFFERSON CITY, MO 65109 • TOLL FREE (800) 881-2249 • FAX (877) 893-2317
www.wrensolutions.com
DIMENSIONS
(All dimensions are in inches)
All Products Are Subject to the Current Version of Wren Terms and Conditions
WARRANTY INFORMATION
Wren warrants EG8-PTZ-IP housing for five (5) years
and the electronics for one (1) year from the purchase
date, recorded as the ship date on Wren’s invoice,
against any defects in material or workmanship as long
as the product is used for the purposes for which it was
intended. Warranty claims will be processed only when
accompanied by original order numbers which include:
purchase order number, sales order number, invoice
number and serial number (if applicable).
RETURNS
In order to return parts to the factory for repair or credit, please call the factory at
(800) 881-2249 or (573) 893-2249 to obtain a Return Authorization (RA) number.
All returns are subject to Wren’s RA Policy. Goods returned for credit should be
in their original condition—new and unused. All merchandise returned by the buyer
for credit, and accepted by Wren, may be subject to a 20% restocking charge.
Products returned within 31-90 calendar days from the purchase date will be
subject to a 20% restocking fee. Products may not be returned more than 90
calendar days from the purchase date. Custom, special order and OEM products
may not be returned.
Wren®, the Wren logo, The Power to See Your Business, Wren IP Solutions, No Tools Required and Solution Set Series are trademarks of Wren. The trademarks that are followed by ® are
registered trademarks in the U.S. All other trademarks and/or registered trademarks mentioned herein are properties of their respective owners and are used for reference purposes only.
The use of these trademarks does not indicate any affiliation with or sponsorship of or by Wren. ©2006 Wren. All rights reserved.
/
