Wren MiniGlobe IP-MGW Install Manual

Brand: Wren

Model: MiniGlobe IP-MGW

Type: Install Manual

IP MiniGlobe, Wall Mount

Instructions

PROPERTY OF WREN Page 1 of 4 7L237 REV-C 9/21/2007

124 WREN PARKWAY • JEFFERSON CITY, MO 65109 • TOLL FREE (800) 881-2249 • FAX (877) 893-2317

www.wrensolutions.com

DESCRIPTION

The Wall-Mounted IP MiniGlobe (MGW-IP) is an integrated solution

including a high-quality camera, lens and housing. Like all Wren products,

it is designed for quick and simple installation and servicing.

SUGGESTED INSTALLATION EQUIPMENT

• #1 Phillips-head screwdriver, for dome and housing screws

• #2 Phillips-head screwdriver with a long (at least 6”) shaft, or

other appropriate tools for installing mounting hardware.

• Pliers

COMPONENT LIST [Figure 1]

1. Upper Housing

2. #4-40 screws (3)

3. Main Bracket Assy

4. Dome

5. Camera Assy

6. #8 Pan-Head Sheet-Metal Screws (2) (not shown)

7. DC Power Pigtail (not shown)

8. Butt Connectors (2) (not shown)

WARNINGS AND SAFEGUARDS

Prior to installation and use of this product, please observe the following

warnings:

1. Installation and servicing should be done by qualified personnel, and

all work done should conform to local codes.

2. Using replacement parts or accessories other than Wren may

invalidate the warranty.

3. This unit is designed to operate on either IEEE 802.3af POE or

12VDC power. Do not bring any other voltages into the housing.

4. Make sure that the installation method is capable of supporting

three (3) times the weight of the MGW-IP housing and enclosed

contents.

MINIGLOBE CAMERAS:

???

High-Resolution Color Board

Camera

INDOOR IP HOUSINGS:

MGW-IP

IP MiniGlobe, Wall Mounted

Figure 1

PROPERTY OF WREN Page 2 of 4 7L237 rev-C 9/21/2007

124 WREN PARKWAY • JEFFERSON CITY, MO 65109 • TOLL FREE (800) 881-2249 • FAX (877) 893-2317

www.wrensolutions.com

PREPARATION

1. Carefully unpack box and verify that all components listed are

included [Figure 1].

2. Remove the dome assembly from the upper housing by

loosening the two (2) black #4-40 Phillips-head screws with a

#1 Phillips screwdriver. Twist dome counter-clockwise slightly

to align the screw heads with the keyhole openings in the

dome, remove and set aside, taking care that dome does not

become scratched or damaged.

3. Remove the camera assembly from the hanger bracket by hand-

loosening the knurled knobs and sliding the camera out (do not

remove knobs). Carefully, place camera aside.

4. Remove the Upper Housing from the Main Bracket Assy by

removing the black #4-40 Phillips-head screw with a #1 Phillips

screwdriver.

5. Lay out the required mounting hole pattern (see figure on last page) in desired installation location and

drill holes as required. The top and bottom holes should accommodate the selected mounting hardware,

while the middle hole must be big enough to provide clearance for the cables coming into the housing.

6. Run Cat5 (and, optionally, 12VDC leads) to desired location and through the cable access hole drilled in

the previous step.

NOTE

POE power must be IEEE 802.3af compliant. Optional 12VDC power must be

from a regulated power source. (See Master Power Supply Instructions for

wiring/installation instructions.)

INSTALLATION

1. Install #8 Phillips-head screw (or other suitable hardware) into both holes in wall and leave approximately

1/8” to 3/16” gap between screw head and wall or vertical surface.

2. Feed Cat5 (and, optionally, the 12VDC power leads) through the mounting plate access hole.

3. Install upper housing onto wall by aligning the lower screw with the slot in the bracket and then aligning

the upper keyhole slot over upper screw and sliding the housing downward until seated. Tighten both

screws until snug, but DO NOT OVER-TIGHTEN.

4. Connect the Cat5 cable to the RJ45 jack. If 12VDC direct power is required, use the included DC Power

Pigtail and butt connectors and connect it to the power barrel lead (center pin is positive).

TIP

To use Butt Connectors, twist the leads together, place joined leads

into wide end of connector, crimp with pliers.

WARNING!

Ensure properly polarity when connecting 12VDC (center pin positive).

Applying incorrect voltage or polarity will invalidate warranty.

5. Push cable(s) back into mounting surface to remove excess slack.

6. Place camera into hanger bracket and connect the camera cable. See Figure 2 for proper camera

orientation.

7. Make final pan and tilt adjustments and hand tighten knurled knobs to secure. [Figure 2]

8. To make adjustments to the lens, loosen the lens locking screws, adjust focal length and focus, and

retighten the lens locking screws snuggly (but do not over-tighten). [Figure 2]

9. Re-install Upper Housing onto bracket and secure with single #4-40 screw.

PROPERTY OF WREN Page 3 of 4 7L237 rev-C 9/21/2007

124 WREN PARKWAY • JEFFERSON CITY, MO 65109 • TOLL FREE (800) 881-2249 • FAX (877) 893-2317

www.wrensolutions.com

NOTE

Depending on the end-style of the Cat5 cable, the Upper Housing may push slightly to one side.

This is not unusual, and the Housing will become properly aligned when the dome is installed.

10. Install the dome by positioning the keyhole slots on dome flange over the two #4-40 screws in the

bracket and twisting clockwise slightly. Tighten screws with #1 Phillips screwdriver, but DO NOT OVER-

TIGHTEN.

NOTE

Fingerprints or smudges may be removed from the Housing with a damp rag or any standard light-

duty surface cleaner. DO NOT use liquid cleaners (except for those that are specifically designed

for optical-grade acrylic) on the Dome as they may degrade the optical quality.

TROUBLESHOOTING

If there is no video signal, check the following:

1. Software cannot attach to MGW-IP, and no LED’s are lit:

a. Verify proper insertion of Ethernet cable at both ends of cable (if using POE). If LED’s are still

not lit, 12VDC (center pin positive) can be connected to the optional power input to verify

operation of the MGW-IP.

b. Verify proper voltage and polarity (if using direct power).

2. Software cannot attach to MGW-IP, but some LED’s are lit:

a. Red LED indicates that the unit is getting power, and should be solid red. Green LED indicates

network status and should be blinking consistently if everything is working normally.

b. If red LED is on and green LED is not flashing, check Ethernet connections on both ends.

3. Software can attach to MGW-IP, but no video is present:

a. Check small cable connection in back of camera and ensure that it is completely inserted and not

damaged.

b. Ensure that “MiniGlobe” device is selected for the subject IP address in Wren VMS under Edit

Camera.

c. If viewing through Internet Explorer

(“IE”), ensure that the ActiveX control

has been installed (see Windows and/or

IE instructions for details on permitting

the installation of ActiveX controls).

4. See also: Troubleshooting section in Wren VMS

instructions.

5. Wren Technical Support is available from 8am to

5pm CST Mon-Fri at 1-800-881-2249.

Outline Dimensions

PROPERTY OF WREN Page 4 of 4 7L237 rev-C 9/21/2007

124 WREN PARKWAY • JEFFERSON CITY, MO 65109 • TOLL FREE (800) 881-2249 • FAX (877) 893-2317

www.wrensolutions.com

SPECIFICATIONS

Input Voltage POE (802.3af compliant), or

12VDC ± 10%

Power Consumption Approx. 7W

Power Connection DC Jack, OD 5.5mm ID 2.1mm

(for use when not using POE)

Video Connections RJ45 (digital via Ethernet)

BNC (analog output)

Networking Ethernet 10baseT or 100baseT

Algorithm (video) MPEG4 (simple profile) or MJPEG

Algorithm (still) JPEG

Frame Rates Up to 15 fps at 704x480

Up to 30 fps at 352x240 or lower

Viewing System Req. Microsoft Windows 98SE or later

Internet Explorer 5.0 or later

Environment Indoor use only

0° - 50°C (32° - 122°F)

Up to 95% RH (non-condensing)

Weight 1.60 lb

All Products Are Subject to the Current Version of Wren Terms and Conditions

WARRANTY INFORMATION

Wren warrants MGW-IP housing for five (5) years, and

the camera and other electronics for one (1) year from

the purchase date, recorded as the ship date on Wren’s

invoice, against any defects in material or workmanship

as long as the product is used for the purposes for

which it was intended. Warranty claims will be

processed only when accompanied by original order

numbers which include: purchase order number, sales

order number, invoice number and serial number (if

applicable).

RETURNS

In order to return parts to the factory for repair or credit, please call the factory at

(800) 881-2249 or (573) 893-2249 to obtain a Return Authorization (RA) number.

All returns are subject to Wren’s RA Policy. Goods returned for credit should be

in their original condition—new and unused. All merchandise returned by the buyer

for credit, and accepted by Wren, may be subject to a 20% restocking charge.

Products returned within 31-90 calendar days from the purchase date will be

subject to a 20% restocking fee. Products may not be returned more than 90

calendar days from the purchase date. Custom, special order and OEM products

may not be returned.

Wren®, the Wren logo, The Power to See Your Business, Wren IP Solutions, No Tools Required and Solution Set Series are trademarks of Wren. The trademarks that are followed by ® are

registered trademarks in the U.S. All other trademarks and/or registered trademarks mentioned herein are properties of their respective owners and are used for reference purposes only.

Mountin

Hole Pattern

(

not to scale

)

Wren MiniGlobe IP-MGW Install Manual

Wren MiniGlobe IP-MGW Install Manual

Wren MiniGlobe IP-MGW Install Manual

Related papers

Other documents